Poulan ProメーカーPC1538Cの使用説明書/サービス説明書
ページ先へ移動 of 48
| OWNER'S MANUAL MODEL NO. PC1538C 15 HP 38 Inch Lawn Tractor Assembly • Operation • Maintenance • Service and Adjustments • Storage • Troubleshooting • Repair Parts For Parts and Service, contact our authorized distdbutor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 Poulan 186888 2.
SAFETY RULES _ SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS ,_ IMPORTANT: THIS CUTTING"RIACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND TI_ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
SAFETY RULES '_Safe Operation Practices for Ride-On Mowers _lb Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary.
PRODUCT SPECIFICATIONS GASOLINE CAPACITY AND TYPE: OIL TYPE (API-SF-SJ): 1,25 GALLONS UNLEADED REGULAR SAE 30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: 3 PINTS SPARK PLUG: CHAMPION RC12YC GAP: .030") GROUND SPEED (MPH): FORWARD: 1st 1,1 2nd 2.
UNASSEMBLED PARTS Steering Wheel Steering Wheel Insert i i Steering Wheel Adapter Steering Extension Shaft Steering Boot (1) Large Flat Washer (1) Locknut 1/2-20 (1) Hex Bolt 1/4-28 x 1-1/4 @ (1) Lock.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
ASSEMBLY HOW TO SET UP YOUR TRACTOR INSTALL SEAT (See Fig. 2) Adjust seat before tightening adjustment bolt. Remove adjustment bolt, lock washer and fiat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Pivot seat upward and remove from the cardboard pack- ing.
ASSEMBLY CHECKTIRE PRESSURE ,/CHECKLIST The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. R N H L I1 REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION ENGINE O.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while op- erating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
OPERATION TO OPERATE MOWER (See Fig. 6) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. Select desired height of cut.
OPERATION CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidicgas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer.
MAINTENANCE FILL tN DATES A SYOOCOMPLETE REGULAR SERVICE !'_4"_""£-q_'/_£'_F SERVICE DATES Check Brake Operation _ Check Tire Pressure Check Operator Presence and T Int.
MAINTENANCE TRACTOR Always observe safety rules when performing any main- tenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See"TO ADJUST B RAKE" in the Service and Adjustments section of this manual).
MAINTENANCE BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. Keep battery and terminals clean. Keep battery bolts tight. • Keep small vent holes open.
MAINTENANCE CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE COOLING FINS (See Fig. 12) Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from overheating.
MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS: Depress clutch/brake pedal fully and set parking brake. Place gearshift lever in neutral (N) position. Place attachment clutch in "DISENGAGED" position.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
SERVICE AND ADJUSTMENTS R.H, SUSPENSION ARM ,,,._ ;: ._ .:._ MANDREL ENGINE PULLEY PULLEY RETAINER SPRING IDLER PULLEYS MANDREL PULLEY FIG. 20 TO CHECK AND ADJUST BRAKE (See Fig. 21) Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.
SERVICE AND ADJUSTMENTS Position the gear shift lever in the neutral (N) posi- tion. Tighten adjustment bolt securely. NOTE: If additionalclearanceis needed to get toadjustment bolt, move mower deck height to the lowest position. GEARSHIFT LEVER ADJUSTMENT BOLT NEUTRAL LOCK GATE FIG.
SERVICE AND ADJUSTMENTS Lift seat pan to raised position. Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor. Install new battery with terminals in same position as old battery. First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown.
STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more, WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING POINTS PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power Excessive vibration CAUSE 1. Out of fuel. 2. Engine not =CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven Mower blades will not rotate Poor grass discharge Headlight(s) not working (if so equipped) Battery will not charge Engine "backfires" when turning engine "OFF" 1.
TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 SCHEMATIC 4k BATFERY K ____ RED AMMETER (OPTIONAL) WHITE G A1 IGNITION SWITCH IGNITION SWITCH POSITION CIRCUIT "MAKE" OFF M+G+A1.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 ELECTRICAL 22 25 48 21 26 I I I I Ii f / I I I I I I i t i [ I I I 29 27 I I I I I I 28.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-20unc X 3/4 8 176689 Box Battery 16 17613.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 CHASSIS 208 30 207 26 33 2O6 3 26 5 25 10 35 34 26 12 29 28 13 • _ . • 208 cha ssis-pl,lt_stlt_50 3O.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 CHASSIS KEY PART NO. NO. DESCRIPTION 1 174619 2 176554 3 17060612 5 155272 9 168336X010 10 72140608 11 174996 12 145660 13 17.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 DRIVE 26 i 27 32.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 2 146682 3 123666X 4 12000028 5 121520X 6 17060512 8 165619 1.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 STEERING 47 68 67 67 65 3O 67 43 I iIz'l _l I I 6 34.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 STEERING KEY PART NO. NO. DESCRIPTION 1 140044X428 2 175131 3 169840 4 169839 5 6266H 6 121748X 7 19272016 8 12000029 9 3366R.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 ENGINE 2_ 3 72 81 4 31 78 33 37 29 OPTIONAL EQUIPMENT Spark Arrester 38 14 23 I 36.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 ENGINE KEY PART NO. NO. DESCRIPTION 1 2 3 170551 17720408 4 137352 13 165291 14 148456 16 11050600 23 169837 29 137180 31 184.
REPAIR PARTS TRACTOR -- MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 SEAT 12 8 _,_ ! 11 . KEY NO. 1 2 3 4 5 6 7 8 9 10 12 13 PART NO. 127426X 140551 71110616 19131610 145006 73800600 124181X 17000616 19131614 182493 121246X 121248X DESCRIPTION Seat Bracket Seat Pivot Bolt Hex 3/8 - 16 X 1 Washer 13/32 X 1 Xl0Ga.
REPAIR PARTS TRACTOR -- MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 DECALS 8 9 7 12 1 14 6 8 15 3 17 KEY PART NO. NO. 1 185413 3 184768 4 170563 6 157140 7 158168 8 172200 9 158166 12 181552 14 181553 15 145005 16 156369 KEY PART DESCRIPTION NO.
REPAIR PARTS TRACTOR -- MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 MOWER LIFT 7 11 5 6 3 19 13 13 32 13_ 32 19 2O 15 i_ 161718 20 20 15 4O.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 MOWER LIFT KEY PART NO. NO. DESCRIPTION 1 159460 2 159471 3 105767X 4 12000002 5 19211621 6 120183X 7 109413X 8 124526X 11 13.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 MOWER DECK 2 2 86 68 28 26 42.
REPAIR PARTS TRACTOR - - MODEL NUMBER PC1538C, PRODUCT NUMBER 954 57 09-32 MOWER DECK KEY PART NO. NO. 1 170280 2 72140506 3 138017 4 169970 5 4939M 6 178024 8 850857 9 10030600 10 140296 11 134148 11.
SERVICE NOTES 44.
LIMITED WARRANTY 6. 7. The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and workmanship.
POLICY Issued January 1980 WARRANTY Revised January 1991 LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWERTRAIN COMPONENTS A. Products Warranted Peerless Gear and Machine Division of Tecumseh Products Co.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION "M ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
Poulan.
デバイスPoulan Pro PC1538Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan Pro PC1538Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro PC1538Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro PC1538Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro PC1538Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro PC1538Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro PC1538Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro PC1538Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro PC1538Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
