Poulan ProメーカーPDGT26H48Aの使用説明書/サービス説明書
ページ先へ移動 of 48
185109 Re v . 1 06.03.03 RH/TR Printed in U.S .A. 02139 OWNER'S MANUAL MODEL: PDGT26H48A LA WN TRACTOR Always W ear Eye Protection During Operation W ARNING: Read the Owner's Manual and fol- low all W arn ings and Safety In struc - tions. Fail ure to do so can result in serious injury .
2 I. GENERAL OPERA TION • Read, understand, and follow all instr uctions in the manual and on the machine bef ore star ting. • Only allow responsib le adults, who are f amiliar with the in struc tions, to operate the machine . • Clear the area of objects such as rocks , to ys, wire , etc.
3 • Be sure the area is clear of other people bef ore mow- ing. Stop machine if anyone enters the area. • Nev er carry passengers or children ev en with the b lades off . • Do not mow in re verse unless absolutely necessary . Al wa ys look do wn and behind bef ore and while back- ing.
4 CONGRA TULA TIONS on your purchase of a ne w tractor . It has been designed, engineered and manu fa c tured to give you the best possib le dependability and perf ormance.
5 UNASSEMBLED P AR TS (2) Hex Bolts 1/4-20 x 3/4 (2) Keps Nuts 1/4-20 Battery (2) Keys Slope Sheet Keys Gauge Wheels (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Adjusting Bars (4) Retainer Springs (.
6 ASSEMBL Y Y our ne w tractor has been assemb led at the f actor y with e xception of those par ts left unassemb led for shipping purposes. T o ensure safe and proper oper ation of your tr actor all par ts and hardware y ou assemble m ust be tightened securely .
7 ASSEMBL Y FIG. 4 02466 02464 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T FIG. 3 NO TE: Y ou may now roll or driv e your tr actor off the skid. F ollow the appropriate instruction below to remov e the tractor from the skid. INST ALL SEA T (See Fig.
8 ASSEMBL Y FIG. 5 FIG. 6 INST ALL MO WER AND DRIVE BEL T (See Figs. 6 and 7) Be sure tractor is on le v el surf ace and mow er suspension arms are raised with attachment lift control. Engage park- ing brak e. • Cut and remov e ties securing anti-sw a y bar and belts.
9 ASSEMBL Y ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRA C- T OR, WE WISH T O ASSURE THA T Y OU RE CEIVE THE BEST PER FORM ANCE AND SA TISF ACTION FR OM THIS QU AL ITY PROD UCT . PLEASE REVIEW THE FOLLO WING CHECKLIST : ✓ All assembly instructions hav e been completed.
10 These symbols ma y appear on your tr actor or in literature supplied with the product. Lear n and understand their mean- ing. OPERA TION DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Model.
11 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRACT OR. Compare the illustrations with y our tractor to f amiliarize y ourself with the location of v arious controls and adjustments. Sav e this man ual f or future ref erence.
12 OPERA TION FIG. 8 MO WER BLADES - • T o stop mo wer b lades ,mov e attachment clutch s witch to “DIS EN GA GED” po si tion. GROUND DRIVE - • T o stop ground drive , depress brak e pedal into full “BRAKE” position. IMPORT ANT : THE MO TION CONTROL LEVER RETURNS T O NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULL Y DEPRESSED .
13 OPERA TION T O OPERA TE MO WER (See Fig. 10) Y our tractor is equipped with an oper ator presence sens ing s witch. Any attempt by the oper ator to leav e the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut.
14 OPERA TION T O ST ART ENGINE (See Fig. 7) When star ting the engine f or the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mo v e fuel from the tank to the engine. • Be sure freewheel control is in the tr ansmission en gaged position.
15 OPERA TION FIG. 12 PURGE TRANSMISSION CA UTION: Never engage or disengage freewheel le ver while the engine is run- ning. T o ensure proper operation and perf or mance , it is rec om - mend ed that the transmission be purged bef ore operating tractor f or the fi rst time.
16 BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace .
17 MAINTENANCE TRA CT OR Alwa ys observe saf ety rules when performing any main- te nance. BRAKE OPERA TION If tractor requires more than six (6) f eet stopping distance at high speed in highest gear , then br ake m ust be adjusted. (See “T O ADJUST BRAKE” in the Service and Ad just ments section of this manual).
18 MAINTENANCE TRANSAXLE COOLING The f an and cooling fi ns of transmission should be kept clean to assure proper cooling. Do not attempt to clean f an or transmission while engine is running or while the transmission is hot. T o prev ent pos- sible damage to seals , no not use high pressure water or steam to clean transaxle.
19 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spar k arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whiche v er occurs fi rst.
20 SER VICE AND ADJUSTMENTS T O REMO VE MO WER (See Fig. 19) • Place attachment clutch in “DIS EN GA GED” position. • If equipped, tur n height adjustment knob to low est set ting. • Low er mower to its lo west position. • Disengage belt tension rod from lock br ack et.
21 Check adjustment on right side of trac tor . P osition any b lade so the tip is pointing straight f orw ard. Measure distance "B" at front and rear tip of the blade . • Bef ore making any necessar y ad just ments, check that both front plate links are equal in length.
22 T O REPLA CE MO WER BLADE (SEC OND AR Y) DRIVE BEL T (See Fig. 25) P ark the tractor on le v el surf ace. En gage parking brake . • Remov e mower (See “T O REMO VE MOWER” in this section of manual). • Remov e screws from R.H. and L.H. mandrel cov ers and re m ove c ove r s.
23 SER VICE AND ADJUSTMENTS T O ADJUST A TT A CHMENT CLUTCH (See Fig. 26) The electric clutch should provide years of service. The clutch has a built-in br ake that stops the pulle y within 5 seconds. Eventually , the inter nal brak e will wear which ma y cause the mower b lades to not engage , or , to not stop as required.
24 00663 RE TA I N ING RING WA S H ERS FIG. 29 AXLE CO VER T O REMO VE WHEEL FOR REP AIRS FRONT WHEEL (See Fig. 29) • Block up axle securely . • Remove axle co v er , retaining ring and washers to allo w wheel remov al. • Repair tire and reassemble .
25 TERMINAL GU ARD TERMINAL A CCESS DOOR FIG. 31 HEX BOL T KEPS NUT POSITIVE (RED) CABLE NEGA TIVE (BLA CK) CABLE SER VICE AND ADJUSTMENTS REPLA CING B A TTER Y (See Fig. 31) W ARNING: Do not short battery ter- mi nals by allowing a wrenc h or any other object to contact both terminals at the same time.
26 T O REPLA CE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the gri ll. • Replace b ulb in holder and push b ulb holder securely back into the hole in the bac kside of the grill.
27 SER VICE AND ADJUSTMENTS CLAMP SCREW FIG. 34 FIG. 33 SWIVEL CLAMP SCREW ST OP ENGINE T O AD JUST THRO TTLE CON TROL CABLE (See Fig. 33) The throttle control has been preset at the f actor y and ad just ment should not be necessar y . Chec k adjustment as described below bef ore loosening cable .
28 ST ORA GE Immediately prepare your tr actor f or storage at the end of the season or if the tractor will not be used f or 30 da ys or more. W ARNING: Ne ver store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
29 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se v eral minutes bef ore attempting to start. 4. Bad spar k plug.
30 PROBLEM CA USE CORRECTION Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, s witches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutc h department.
31 TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 SCHEMA TIC BATTERY FUSE RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTION.
32 30 33 24 42 43 40 26 28 25 50 29 27 27 41 16 12 12 11 10 8 2 1 27 D . C . A M P E R E S 45 81 46 89 22 79 21 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 ELECTRI.
33 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 ELECTRICAL 1 144927 Batter y 2 74760412 Bolt He x Head 1/4-20 x 3/4 8 7603J T ray , Bat ter y 10 145211 Bolt Btr F rt 1/4-20 x 7.
34 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 CHASSIS AND ENCLOSURES 31 68 43 34 47 24 39 17 86 166 2 19 20 16 17 56 21 47 17 28 91 1 36 36 50 17 17 8 156 156 156.
35 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 CHASSIS AND ENCLOSURES 1 180375 Rail, F r ame RH 2 175282 Dra wbar , Gt 5 163976X428 Dash 6 157882 Dash Asm., Low er 7 17720408 Screw , Thd Cut 1/4-20 x 1/2 8 145166 Suppor t, Batter y 14 175260X428 Hood Asm.
36 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 GROUND DRIVE 9 7 55 65 130 131 34 35 37 38 40 41 42 68 46 36 37 38 64 39 56 29 89 132 77 70 74 89 120 89 133 120 98 .
37 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 GROUND DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - T ransaxle Hydro Gear 331-3000 (Order P ar ts F rom T rans- axle Manuf acturer) 2 7070E K ey Sq.
38 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 STEERING ASSEMBL Y 47 48 46 49 50 8 6 29 28 23 31 41 22 21 20 44 1 24 14 25 34 33 32 6 27 42 27 6 19 15 14 35 18 16 .
39 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 STEERING ASSEMBL Y 1 180656 Wheel, Steering 2 178557 Axle Asm., F ront 3 6855M Fitting, Grease 4 161849 Spindle Asm, LH 5 161848 Spindle Asm., RH 6 6266H Bearing, Race Thrust Harden 7 121748X W asher 25/32 x 1-5/8 x 16 Ga.
40 KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv en in U .S . inches 1 inch = 25.4 mm 1 - - - - - - - Engine Br iggs , Model No . 446777 (Order par ts from engine manuf.) 2 149723 Muffl er Side 8 121361X Pulley V -Idler 9 177748 K eeper Asm.
41 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 SEA T ASSEMBL Y 1 171684 Seat 2 140551 Brac ket, Piv ot Seat 4 127018X Bolt, Shoulder 5/16-18 x .62 5 145006 Clip , Push-In Hinged 6 73800600 Nut, Crownloc k 3/8-16 7 124181X Spring, Seat Cprsn.
42 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 DECALS 23 1 3 9 14 4 23 10 19 6 8 17 11 KEY P ART NO . NO . DESCRIPTION KEY P ART NO .
43 KEY P ART NO . NO . DESCRIPTION 1 121006X Rod Asm., Lev er 2 180045 Shaft Asm., Lift Vgt 3 159189 Le v er Asm., Lift Rh 4 12000022 E-Ring T r uarc #5133-87 5 19292016 W asher 29/32 x 1-1/4 x 16 Ga. 6 71110624 Bolt, Fin He x 3/8-16 x 1-1/2 7 175830 Grip, Handle 8 175831X421 Button, Plunger 9 122364X Plunger , Le v er Lift 10 183894 Spring 0.
44 57 56 118 116 119 5 117 46 45 33 46 45 33 30 30 30 32 39 21 20 18 21 31 1 32 31 36 36 52 24 25 26 27 28 29 18 8 11 13 16 100 113 17 48 19 5 6 3 14 15 47 49 49 49 49 130 43 121 126 97 115 50 50 98 42 99 42 114 110 112 21 122 42 97 36 37 184 mower_dec k.
45 REP AIR P AR TS TRA CT OR - MODEL NUMBER PDGT26H48A, PRODUCT NUMBER 954 56 95-30 MO WER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv en in U .S . inches 1 inch = 25.4 mm 1 180358X421 Deck W eldment Mo wer 48 3 178915 Brac ket Asm.
46 LIMITED W ARRANTY The Manuf acturer warr ants to the original consumer purchaser that this product as manufactured is free from def ects in materi- als and work man ship.
47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Y our POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLACEMENT P ARTS: 1.
デバイスPoulan Pro PDGT26H48Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan Pro PDGT26H48Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro PDGT26H48Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro PDGT26H48Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro PDGT26H48Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro PDGT26H48Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro PDGT26H48Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro PDGT26H48Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro PDGT26H48Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
