PowermaticメーカーTS29の使用説明書/サービス説明書
ページ先へ移動 of 40
Instruction Manual & Parts List M-0460270 (800) 274-6848 ww w .wmhtoolgroup.com SPINDLE SHAPER Model TS29 This Manual is Bookmarked.
W arranty & Service WMH T ool Group warrants every product it sells. If one of our tools needs service or repair , one of our Autho- rized Repair S tations located throughout the United S tates can give you quick service.
T ABLE OF CONTENTS Safety Rules ................................................................................................................... ................... 4 - 6 Safety Decals ...............................................................
4 As with all machines, there is a cert ain amount of hazard involved with the use of this shaper . Use the machine with the respect and caution demanded where safety precautions are concerned. When normal safety precautions are overlooked or ignored, personal injury to the operator can result.
5 Short stock. Never shape stock less than 12 inches in length without special fixtures. Where practical, shape longer stock and cut to size. 12 inch rule. When shaping, never allow your hands to come closer than 12 inches to the cutters. Hand safety .
6 Health hazards. Some dust created by power sanding, sawing, grinding, drilling and other construction activities cont ains chemicals known to cause cancer , birth defects or other reproductive harm. Some ex- amples of these chemicals are: * Lead from lead-based paint.
7 SAFETY Familiarize yourself with the location and content of these safety decals on your shaper . ! FIGURE 4 W ARNING DO NOT ENGAGE SPINDLE LOCK WHILE MACHINE IS RUNNING 6293077.
8 Motor ...................................................................... TEFC 7.5HP , 3Ph, 230/460V , 60Hz S tarter ...................................... 230/460V Magnetic w/ 24V low voltage control circuit Overall dimensions ..................
9 UNP ACKING Open shipping container and all separate cartons con- taining accessories. Report any damage immediately to your distributor . Read the instruction manual thor- oughly for assembly , alignment, maintenance and safety instructions.
10 5. Secure the machine to the floor with good qual- ity lag screws through the holes in the bottom of the cabinet. 6. Exposed metal parts such as the table top have been given a protective coating at the factory . This should be removed with a soft cloth and solvent (such as mineral spirits).
11 FIGURE 12 INTERCHANGEABLE SPINDLE INST ALLA TION One of the features of this machine is that it will ac- cept interchangeable spindles with a drawbar or with- out a draw bar . Router bits can also be used on this shaper . INTERCHANGEABLE SPINDLE WITH DRA WBAR 1.
12 4. Disengage spindle lock before operating. NOTE: Whenever possible, the cutter should be posi- tioned on the spindle in such a way that the cut is being performed under the surface of the workpiece. W ARNING: Always place the "keyed" washer (C) on the spindle before threading the nut.
13 FIGURE 19 MITRE GAUGE & CLAMP Mount mitre gauge and clamp to the sliding table as follows (Figure 19): 1 . Insert post (A) of the clamp assembly down through hole (B) of the mitre gauge body (C), and thread post (A) into hole (D) of sliding table.
14 ADJUSTMENTS Control Panel Instructions The elements of the control panel are as follows: (See Figure 24). A. power indicator B. on-off switch C. forward/reverse switch D. start indicator E. emergency stop 1. Make certain the spindle lock is disengaged as explained in the section "S pindle Lock" and that the cabinet door is closed.
15 The cutting speed should always exceed 40 m/s to lessen risk of kickback but should not exceed 70 m/s to lessen the risk of tool damage. T o change the speed and adjust the proper belt ten- sion, proceed as follows: 1. Disconnect machine from power source.
16 SPINDLE TIL TING The machine should come to a complete stop before the spindle is tilted, and the insert with the oval slot should be placed into the table. Make sure the cutter does not touch the table or the fence when in tilted position. 1. Loosen the knob (C) on the front handwheel (D).
17 SLIDING T ABLE ADJUSTMENT There are six adjustable eccentric rollers (A) on the sliding table, shown in Figure 31. Wherever the table is unstable or not traveling in line, adjust the sliding table as follows: 1. Use open end wrench (B) to adjust the rollers.
18 POSITION OF COLLARS When shaping with collars, the collar must have suffi- cient bearing surface, as shown in Figure 35. Also the work must be fairly heavy relative to the cut being made. Under no circumstances should a short, light workpiece be shaped against the collars, as shown in Figure 36.
19 COPYING (MACHINING WITH A JIG) When using the same procedure on multiple workpieces, a jig or template can be made to facilitate the operation: 1. Prepare the jig (A) to accomodate your original workpiece. See Figure 40. 2. Place the jig (A) against the table ring guide shoul- der (B).
20 The bearings in the motor are sealed for life and do not require lubrication. The spindle bearing should be lubricated every 200 hours of use by using the grease gun (A) supplied. See Figure 41. T wo grease fittings, one of which (B) is shown, are supplied on the spindle housing for this purpose.
21 T rouble-Shooting for Model TS29 Shaper PROBLEM POSSIBLE CAUSE SOLUTION [with page #] Machine will not start. 1. Faulty switch. 1. Replace switch. 2. Cord damaged. 2. Have cord replaced by authorized service person. 3. Not connected to power source.
22 T rouble-Shooting for Model TS29 Shaper PROBLEM POSSIBLE CAUSE SOLUTION [with page #] Depth of cut not uniform. 1. Misalignment. 1. Adjust outfeed fence. 2. Side pressure not uniform. 2. Use hold-downs or stock feeder; keep pressure against fence or collars consistent.
23 Parts List: Fence Assembly (TS29 Shaper) No . Part No. Description Quantity 1 TS29-001 S pring Guard ....................................................................................................... 1 2 TS-1503021 Socket Head Cap Screw , M6 x 10 .
24 No . Part No. Description Quantity 57 TS29-037 Retaining Ring .................................................................................................... 1 5 8 BB-6204 Ball Bearing 6204 .....................................................
25 Fence Assembly (TS29 Shaper).
26 Parts List: Spindle Assembly (TS29 Shaper) No . Part No. Description Quantity 1 6293033 S pindle Nut, 3/4 .................................................................................................. 1 6293034 S pindle Nut, 1 .................
27 Spindle Assembly (TS29 Shaper).
28 Parts List: Cabinet Assembly (TS29 Shaper) No . Part No. Description Quantity 1 TS-1502041 S o ck e t H e a d C a p Screw , M5 x 16 ...................................................................... 9 2 TS29-075 T able Insert, 2-1/2" I.D. .
29 Cabinet Assembly (TS29 Shaper).
30 Parts List: Sliding T able Assembly (TS29 Shaper) No . Part No. Description Quantity 1 TS29-095 Main T able .......................................................................................................... 1 2 TS-1504101 S o ck e t H e a d C a p Screw , M8 x 50 .
31 Sliding T able Assembly (TS29 Shaper).
32 Parts List: Speed Indicator (TS29 Shaper) No . Part No. Description Quantity 1 TS29-129 Belt Fork ............................................................................................................ 1 2 TS29-130 Fork Slide .................
33 Speed Indicator (TS29 Shaper).
34 Parts List: Electrical Component s (TS29 Shaper) No . Part No. Description Quantity 1 TS29-139 S peed Indicator Light .......................................................................................... 5 2 TS29-140 S top Button .............
35 Electrical Component s (TS29 Shaper).
36 Parts List: Quill Assembly (TS29 Shaper) No . Part No. Description Quantity 1 TS-149105 Hex Cap Screw , M10 x 35 .................................................................................. 4 2 TS-2361 10 Lock Washer , M10 ...................
37 No . Part No. Description Quantity 55 TS29-177 H andw heel .......................................................................................................... 1 5 6 TS-1503071 Socket Head Cap Screw , M6 x 30 .................................
38 Quill Assembly (TS29 Shaper).
39 Electrical Schematic (TS29 Shaper) T o order p ar t s or reach our service de p artment, please call our toll-free number between 7 : 3 0 a.m. and 6 : 0 0 p.m. (CST), Monday through Friday . Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately .
C WMH TOOLGROUP 2 4 2 0 V a n t a g e D r i v e Elgin, IL 60123 Phone: (800) 274-6848 Website: www.wmhtoolgroup.com POWERMA TIC ALL RIGHTS RESERVED 08/02.
デバイスPowermatic TS29の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Powermatic TS29をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPowermatic TS29の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Powermatic TS29の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Powermatic TS29で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Powermatic TS29を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPowermatic TS29の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Powermatic TS29に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPowermatic TS29デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。