PrecorメーカーEFX EFX 821の使用説明書/サービス説明書
ページ先へ移動 of 48
As sembling and Maintaining the EFX® 821 Elliptical Fitnes s Cr os s tr ainer ™ Prec or Incorporat ed 20031 142nd A venue NE P .O . Bo x 7202 W oodinville, W A USA 980 72 -4002 EFX 821 P AG/ OM 300.
.
As sembling and Maintaining the EFX ‰ 821 Elliptical Fitnes s Cr oss tr ainer ™.
E dition Information ASSEMBLING AND MAINTAINING THE EFX 82 1 ELLIPTICAL FITNESS CROSSTRAINER P/N 300763-101 rev A Copyright ©2011 Precor Incorporated. All rights reserved. Specifications subject to change wi thout notice. Trademark Note Precor, AMT, and E FX are registered trademarks and Preva is a trademark of Precor Incorporated.
Chapter 1 Important Saf ety Ins tructions Read the following precautions thoroughly before you begin assembly, and save them afterward for future refere nce. Safety Precautions Always follow basic safety precautions when using this equipment to reduce the ch ance of injury, fire, or damage.
4 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Never leave the equipment unattended when it is plu gged in. Unplug the equipment from its power source wh en it is not in use, before cleaning it, and before providing authorized service.
Important Safety Instructions 5 Maintain the equipment to keep it in good working condition, as described in the Maintenance section of the assembly and maintenan ce guide. Inspect the equipment for incorrect, worn, or loose components, and then correct, replace or tighten prior to use .
6 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Educating Users Take time to educate users about the I mportant Safety Instructions found in both the User Refe rence Manual and Product Owner’s Manual .
Important Safety Instructions 7 Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this sec tion applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety s tandards.
8 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Industry Canada This Class A digital ap paratus complies with Canadian ICES-003.
Important Safety Instructions 9 The grounding plug on a treadmill or po wer supply looks like the plug shown in one of the following two figures. The power outlet must have the same configuration as the plug. Important: Do not use any power cord adapter with this product.
10 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer.
T able of C ont ents Important Safety Instructions .................................................... 3 Safety Prec autions ................................................................................ 3 Educating Users ..........................
.
Chapter 2 As sembling the EFX WARNING You will need the assistance of two other people to assemble this un it. DO NOT attempt assembly by yourself . Important : The instructions in the following proce.
14 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Begin installation of all fasteners by hand, then partially tighten them. Do not fully tighten faste ners until instructed to do so. Important : When wrench-tightening the screws, make sure the head of the fastener is paralle l to the p roduct surface.
Assembling the EFX 15 Required Tools Wire tie cutter Phillips-head screwdriver Two ⁹⁄₁₆ -inch combination wrenches (open-end and box) SAE Standard socke t set Hardware Kit (not to scale) Table 1.
16 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Fasteners Quantity Bushings 2 Link arm caps 2 Pivot arm caps 2 Pivot axle covers 2 Upright support covers (packaged separatel.
Assembling the EFX 17 Assembling the EFX Assemble the EFX in the order presented. Once you have assembled it, clean the ramp with a so ft cloth dampened in a diluted solution of mild soap and water. To begin assembl y: 1. Feed the cable through the right upright suppor t.
18 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer 2. Attach both upright supp orts to the base frame using eight buttonhead screws, eigh t split washers, and e ight washers. Finger tighten. Figure 4: Attaching the upright supports Installing the Display Console Mount 1.
Assembling the EFX 19 3. Fasten the display console m ount to each upright support by threading a buttonhead screw, washer, and split washer through opposite m ounting holes. Check that the base fasteners are loose before installi ng the display console fasteners.
20 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Installing the Bottle Holder The bottle holder attaches to the right stationary arm handrail. To install the bottle holder: 1. Position the water bottle holder as sho wn and attac h it to the right stationary handrail.
Assembling the EFX 21 Installing the Handlebars CAUTION: Handlebars can s wing and cause injury. Ha ve your assistant hold the handlebar and gently l ower it into a vertical position when the handleb ar assembly is complete. To install the moving handlebars: 1.
22 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer 3. Attach the handlebars to the link arms using two he x head screws, two bushings, and four washers. For e ase of installation, slide the corresponding foot pedal to the top of the ramp before attaching each h andlebar.
Assembling the EFX 23 Attaching the Caps an d Upright Support Cover You will need the arm caps and foot covers to complete the following tasks. To attach the caps and u pright support cov ers: 1. Align the cut-out inside the link arm c ap with the link arm mounting hole.
24 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer 4. Slide the covers down into the base mount. Secure each pair of covers using two self-tapping screws and a Phillips-head screwdriver. Figure 13: Attaching the pivot axle covers 5.
Assembling the EFX 25 Verifying that the Heart Ra te Display is Operational To verify that the heart rate display is operational: 1. Hold on to a stationary handrail and step on the foot pedals. 2. When you are comfortably si tuated, begin pedaling. A pedaling speed above 40 strides per minute must be maintained for several se conds.
.
Chapter 3 Ins talling the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and conn ector locations whenever possible.
28 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Threading the Cable Assembly Earlier in the installation, you threaded the necessary cables through the frame of the base unit an d out the passthrough opening in the console mount.
Installing the Console 29 Connecting Cables After the console has bee n seated, separate the individual cables out of the end of the cable asse mbly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to id entify the cables and connectors.
30 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Completing the Console Installation Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly.
Chapter 4 Self-Po w er ed F eatur es On self-powered equipment, the system initializes and displays the Welcome screen when a user star ts exercising. A minimum rate of motion must be maintained for the banner to appear, as shown in the following table.
32 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins.
Self-Powered Features 33 Using the Optional Power Adapter After connecting the power adap ter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional powe r adapter is in use, make sure that the power supply cord does not create a safety hazard.
34 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician.
Chapter 5 Maint enanc e To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklis t. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty.
36 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er CAUTION: Read and follow the manufacturer’s instructions, particularly dilut ion instructions, before using any clean er on Precor fitness equipmen t.
Maintenance 37 7. Verify that th e unit sits squarely on the floor. All of i ts feet should be touching the floor and the unit should no t rock or wobble when in use. If not, re-level it as described in. Monthly Maintenance DANGER USE EXTREME CAUTION when the rear c over of any EFX is removed.
38 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Storing the Chest Strap If you purchased the optional heart rate chest strap, store it in a place where it remains f ree of du st and dirt (for e xample, in a closet or drawer).
Chapter 6 C ommer cial Car dio v ascular E quipment Limit ed W arr anty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAR EFULLY BEFORE USING YOUR PRECOR INCORPORATED PROD UCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING W ARRANTY TERMS AND CONDITIONS.
40 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines deter mine the warranty for these components.
Commercial Cardiovascular Equipment Limited Warranty 41 This Limited Warranty sha ll not apply to: 1. Software version upgrades. 2. Software defects that do not materially an d negatively affe ct the normal performance of the product under norma l conditions of use.
42 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HA VE NO OBLIGATION OR LIABILITY, WHETHE.
Notes 43.
44 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer.
.
As sembling and Maintaining the EFX® 821 Prec or Incorporat ed 20031 142nd A venue NE P .O . Bo x 7202 W oodinville, W A USA 980 72 -4002 EFX 821 P AG/ OM 3007 63- 101 r ev A 13 January 2011.
デバイスPrecor EFX EFX 821の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Precor EFX EFX 821をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPrecor EFX EFX 821の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Precor EFX EFX 821の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Precor EFX EFX 821で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Precor EFX EFX 821を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPrecor EFX EFX 821の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Precor EFX EFX 821に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPrecor EFX EFX 821デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
