Primera TechnologyメーカーFX400の使用説明書/サービス説明書
ページ先へ移動 of 20
Printer and Stand Install Softwa.
2 Table of Contents 1. S o f t w a r e I n s t a l l a n d S t a n d S e t u p 3 2. Install Foil or Laminate 7 3. Design, Print and Imprint a. D e s i g n t h e L X L a b e l 1 1 b. D e s i g n t h e F o i l L a b e l 1 1 c. Design a Laminate Label 12 d.
3 Introduction: Thank you for purchasing the FX400 metallic foil and laminate thermal printer. You can use your FX400 with a Primera LX400, LX 800 or LX810 printer.
4 Choose “No, not this time” and then click next. Next, select "Install the software automatically" and follow the wizard to complete the installation. You will be prompted that the software has not passed Windows Logo Testing. You must click Continue Anyway to finish the installation.
5 2. Attach the stand pieces together using the included screws. Do not tighten the screws. The stand may need adjustment on ce the printers are in place. The LX printer stand (larger stand) should be on the left side. 3. Place the LX printer on the larger stand.
6 5. Place the FX400 onto th e smaller stand. There are also four indents on the FX400 stand that correspond to the rubber feet on the FX400. 6. Connect power and USB to the FX400 using the included power cord and converter. 7. Your printers are now ready for printing.
7 Section 2: Install Foil or Laminate Install only Primera approved media. Other media may have thermal properties that may not be compatible with the FX400. Follow these instructions to install the media. 1. Push down on the ribbon access window to release the lock.
8 3. The media will come with two cores. One will have the media supply (foil or laminate) and the other will be an empty core . Insert one of the spindles into the empty core. This will be the rewind core. 4. Insert the remaining spindle into the media supply core.
9 6. Place the media supply core on the back set of hubs. The fl ange on the spindle should be on the right side of the printer. First, insert th e left side of the core onto the spring-loaded hub. Then, place the right side of the core on the hub. 7.
10 8. Pull the loose end of the media from the su pply core over the pr int head. Feed it back toward the rewind core. Attach the loose end on the media to the rewind core using tape or the adhesive strip on the rewind core. Note: Make sure the media is flat against th e print head with no folds or wrinkles.
11 Section 3: Design, Print and Imprint A. Design the LX Label Design your LX label according to the instructions that come with you printer. Keep in mind there are variations in the placement of the foil. Foil can be printed over the top of areas that have already been printed on with the LX printe r.
12 Using Photoshop ® or Illustrator ® you can design both aspects of the label in separate layers. This way you can easily a lign the LX inkjet portion with the FX foil portion. To create your output file for use in PTFoil (Section 4D) simply hide each layer and export the file as a BMP, JPG or TIF.
13 2. Set the Printer (LX810 or LX400). 3. Choose the LX Label. 4. Set the size of the label. 5. Choose the FX400 Foil Printer Label. 6. Print the header to be fed into the foil printer by clicking the button on the screen.
14 7. Feed the header into the FX400 Printer. Note: Make sure at least one label is sticking out of the front. Failure to do this could cause feeding/alignment issues when sending the print job.
15 8. Once the label stock is fed into the prin ter, the printer needs to be calibrated. Press the button on the top of the FX400 to calibrate it. 9. Step 6 in the PTFoil application allows you the opportunity to print one test label to see if the Foil Label file is aligned prop erly.
16 Section 4: Adjusting Offsets If the foil border or graphic is not aligned properly on yo ur LX label, you can adjust the placement by following this procedure. Note: It is also possible the FX image itself is offset within the page size of the actual file.
17 3. Choose Advanced Options. Use the graphic below as a guide:.
18 Section 5: Foil/Laminate Only 1. Attach the external paper roll mount to the bottom of the printer. 2. Install the roll of label stock onto the roll mount. Note: Skip Steps 1 and 2 if you have fan-fold labels that are not on a roll. Use steps 3-6 to foil only to these labels.
19 4. Close the top cover of the printer making sure at least one label is sticking out of the front. Failure to do this could caus e feeding/alignment issu es when sending the print job.
20 Section 6: Specifications Imprint Method: Thermal transfer Imprint Resolution: 300 dpi (12 dots/mm) Print Speed: 2” (50.8mm) per second Imprint Width: .75” (19mm) to 4.125” (104mm) Data Interface: USB 1.1 or 2.0 Electrical: DC output: 24 VDC @ 3.
デバイスPrimera Technology FX400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Primera Technology FX400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPrimera Technology FX400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Primera Technology FX400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Primera Technology FX400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Primera Technology FX400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPrimera Technology FX400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Primera Technology FX400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPrimera Technology FX400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
