Primera TechnologyメーカーMaxの使用説明書/サービス説明書
ページ先へ移動 of 20
012004-510887-(01) Connectivity Guide © 2004 All rights reserved. Optical Disc Laminator XL/Pro MAX 510887.qxd 1/21/2004 7:35 PM Page i.
Notices : The information in this document is subject to change without notice. NO W ARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MA TERIAL, INCLUDING, BUT NOT LIMITED TO , THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE.
iii T able of Contents Optical Disc Laminator Guide .....................................................................................1 A. Unpacking and Inspection ...............................................................................1 B. Installing the Laminator Software Driver.
iv Inter activ e F eature in this PDF Document There are interactive features that will allow you to jump to different locations within the document. Each listing in the T able of Content s is interactive. Place the cursor on either the words or the page number .
Optical Disc Laminator Connectivity Guide 1 Optical Disc Laminator Connection Guide THANK Y OU… Thank you for purchasing the Optical Disc Laminator Connectivity Kit. This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro, XL and MA X versions of Optical Disc Duplicators.
2 Optical Disc Laminator Connectivity Guide e. Make certain the Laminator has been plugged into power and turned on. f . Select "Install Softwar e A utomatically" and click Next .
Optical Disc Laminator Connectivity Guide 3 g. Y ou may see a notice like the one shown here stating that the A ccent Disc Laminator has not passed W indows Logo T esting. Click the Install Anyway button to continue installing the printer driver for your Laminator .
4 Optical Disc Laminator Connectivity Guide The following steps describe in detail how to connect the Laminator to your DuplicatorMAX: a. Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown: b. Remove the Input Bin closest to the Laminator Stand to make room for the Laminator's disc tray .
Optical Disc Laminator Connectivity Guide 5 5) F rom the Main Application Screen click Robotics then Options . 6) Enable the Use Laminator checkbox. 7) Click the button labeled Move to (Calibrate) . This will move the Picker Mechanism to the Laminator T ray position.
6 Optical Disc Laminator Connectivity Guide b) While the LEDs are flashing, press the P ause button. The Picking Mechanism will lower to the Laminator T ray P osition. c) A djust the Laminator T ray for ward and back by loosening the adjusting screws located towards the front of the stand.
Optical Disc Laminator Connectivity Guide 7 f) T ighten the A djusting Screws on the front of the Laminator Stand to lock the stand in position. 9. Y ou have now calibrated your Laminator to the Duplicator MAX and are ready to produce discs! D. CREA TING DISCS WITH Y OUR DUPLICA T OR MAX IN PRIMO Laminating your disc jobs is very simple.
8 Optical Disc Laminator Connectivity Guide The Laminator is positioned at the front left corner of the Duplicator . The optional Duplicator XL/Pro Laminator Stand is needed for both of these configurations.
Optical Disc Laminator Connectivity Guide 9 4. Connect the Laminator Stand to the back of the Laminator as shown: 5. Place the Laminator on the Laminator Stand as shown: There are two sets of holes on the underside of your Laminator . Set the Laminator on the stand locating the smaller set of holes on the metal locating pegs on the Laminator Stand.
10 Optical Disc Laminator Connectivity Guide 6. Connect the A uxiliar y Control Cable and P ower Cable the Laminator as shown: 7. Align the Laminator's tray position to the picker . This is done as follows: a. Make certain the Laminator has power and is turned on.
Optical Disc Laminator Connectivity Guide 11 8. The Laminator is now aligned properly . Once the Laminator's Heat Roller has achieved proper operating temperature (indicated by a solidly lit Ready LED on the Laminator's Control P anel), you are ready to laminate discs.
12 Optical Disc Laminator Connectivity Guide 4. Place the Laminator on the stand. The Laminator will need to be placed on the stand with the Laminator's rubber feet resting in the four holes located on the top of the Stand as shown: 5. Using the provided USB Cable, connect the Laminator to your PC as shown: 6.
Optical Disc Laminator Connectivity Guide 13 c. If the Laminator T ray is not in the OUT position, press the Laminate button to eject the Laminator Disc T ray . d. F rom the Main Application Screen click Robotics then Options. e. Enable the Use Laminator checkbox.
14 Optical Disc Laminator Connectivity Guide 8. F rom the Main Application Screen click Robotics then Options . Select Lamination as shown: 9. Set up your print and record job as you normally would per the Duplicator XL/Pro User's Manual. 10. Click the red circle Record button to start your job! 510887.
Optical Disc Laminator Connectivity Guide 15 F . TR OUBLESHOO TING Problem Resolution W ill not Laminate • Check P ower to the Laminator • Make sure that the Ready LED is on and steady indicating .
Printed in the United States of America P/N 510887 510887.qxd 1/21/2004 7:35 PM Page 16.
デバイスPrimera Technology Maxの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Primera Technology Maxをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPrimera Technology Maxの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Primera Technology Maxの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Primera Technology Maxで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Primera Technology Maxを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPrimera Technology Maxの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Primera Technology Maxに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPrimera Technology Maxデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。