ProfileメーカーBA400の使用説明書/サービス説明書
ページ先へ移動 of 19
BA400 BA440 MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Man ual.
I NTRODUCTION Congratulations on your purchase of a Baja state-of-the-art power amplifier. Your selection of a Baja car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Baja amplifier in a new system, you are certain to notice immediate performance benefits.
S AFETY PRECAUTIONS Fuse amplifier's power wire at the battery . Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery.
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current.
Bass Boost For added low frequency performance the amplifiers are equipped with a variable 0~12 dB bass boost @ 45Hz. (BA 400 only) Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output.
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation.
Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 10 to 12 gauge power wire for your connections depending on the amplifier and length of the wire.
7 Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer.
8 High Level inputs have been included to connect the amplifier to a radio without low-level outputs (i.e. factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections.
FOUR CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) 9.
Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-).
TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRIDGED SPEAKER CONNECTIONS S PEAKER CONNECTIONS (BRIDGED) The Baja amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel.
CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier.
. (Please note: If you intend to us e the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the "Flat" setting in order to receive full range output) The Baja amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover type (i.
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself.
S PECIFICATIONS BA400 BA440 Output Power @ 4 Ohm 2 x 200W 4 x 100W RMS Power @ 4 Ohm 2 x 100W 4 x 50W RMS Power @ 2 Ohm 2 x 150W 4 x 75W Bridged RMS @ 4 Ohm 1 x 300W 2 x 150W THD @ RMS Power < 0.
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit.
PROFILE CONSUMER ELECTRONICS, INC. 1 5060 SHOEMAKER AVE S ANTA FE SPRINGS , CA 90 670 TEL: 562-404-9393 FAX: 562-404-9433 WWW.PROFILEUSA.COM By.
デバイスProfile BA400の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Profile BA400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはProfile BA400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Profile BA400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Profile BA400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Profile BA400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はProfile BA400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Profile BA400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちProfile BA400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。