ProFormメーカーPFSY59001の使用説明書/サービス説明書
ページ先へ移動 of 32
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUST OMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76.0 in. Width: 86.5 in. Length: 91.5 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arms Leg Press Seat .
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y .” See the inset drawing. Insert two 1 1/2” x 2 1/2” Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4). Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the indicated ends of the Butterfly Base (4) and the Press Base (6).
4. Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 3/4” Bolts (102), two 3/8” W ashers (48), and two 3/8” Nylon Locknuts (50). Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 3/4” Bolts (102), two 3/8” W ashers (48) and two 3/8” Nylon Locknuts (50).
8 89 48 48 48 89 51 6 50 48 21 Slot 15 8. See the inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the W eight Bumpers (51) and into the holes in the Press Base (6).
9 48 62 50 48 33 9 11 . Secure the Press T op Frame (9) to the Butterfly T op Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” W ashers (48), and two 3/8” Nylon Locknuts (50).
10 14 48 48 10 84 101 10 101 48 48 53 53 14. Insert a 2” Round Inner Cap (101) into the end of a Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8” x 1” Bolts (84) and two 3/8” W ashers (48). Repeat this step with the other Butterfly Arm (10).
20. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Locate the Butterfly Cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the Butterfly Cable to the Right Pivot Arm (85) with a 5/16” x 2 1/4” Shoulder Bolt (79) and a 5/16” Nylon Jamnut (105).
12 22. Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23). W rap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
13 26. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Insert the Ab Cable down through the Press T op Frame (9). Slide a 3/8” W asher (48) and a 5/8” x 3/4” Bushing (66) onto a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press T op Frame (9) and the 3 1/2” Pulley (24).
14 30. Locate the Weight Cable (72). Note that one end of the Weight Cable has a bolt on it, and the other end has a ball on it. Lay the Weight Cable (72) inside the bracket on the Butterfly Base (4) in the manner shown. Attach a 3 1/2” Pulley (24) to the bracket with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
15 35 36 37 34. Wrap the W eight Cable (72) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) to the Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60), a 3/8” W asher (48), and a 3/8” Nylon Jamnut (63). Be sure that the Cable T rap is turned to hold the Cable in place.
16 38. Wrap the W eight Cable (72) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) between the lowest holes in the Adjustable Pulley Plates (23) hanging from the Ab Cable (47) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
17 42. Locate the Leg Press Cable (75) . Attach the Leg Press Cable to the indicated side of the Press Upright (2) with a 3/8” x 3 3/4” Bolt (102) and a 3/8” Nylon Locknut (50). Do not tighten the Nylon Locknut yet. W rap the Leg Press Cable (75) around a 3 1/2” Pulley (24) in the direction shown.
18 46. Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55). W rap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the Pulley and a Cable T rap (25) to the 3/8” x 5 1/2” Bolt (55) on the indicated side of the Press Base (6) with the 3/8” Nylon Locknut (50).
19 50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49). Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).
20 54 55 56 91 46 3 39 54. Lubricate a 1/2” x 4” Bolt (68). Attach the Foot Press Plate (29) to the Press Leg Lever (90) with the Bolt and a 1/2” Nylon Jamnut (36). 55. Press two 3/4” Round Inner Caps (43) into each of the two Pad T ubes (42).
21 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
22 AT T ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (81) to the Ab Cable (47) at the ab pulley station with a Cable Clip (69). ADJUSTING THE BACKREST To adjust a Backrest (12), .
23 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 10 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
25 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly .
26 We ight Cable (72) 2 3 1—Low Pulley 4 8 11 12—Weight Stack 7 6 5 Cable ID 72 47 75 73 9 10.
5/16" Nylon Jamnut (105) Cable Clip (69) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 4 1/2" Pulley (82) (Not shown to scale.
5/16" x 2 1/4" Shoulder Bolt (79) 3/8" x 1" Bolt (84) 3/8" x 1 3/4" Bolt (57) 3/8" x 6" Bolt (59) 1/2" x 4" Bolt (68) 3/8" x 4 3/4" Bolt (60.
2" Square Inner Cap (28) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2” Inner Cap (83) 2 1/2" Square Inner Cap (76) 3” Round Inner Cap (78) 2” Round Inner Cap (78).
P ART LIST—Model No. PFSY59001 R0402A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
92 92 49 39 49 23 25 24 25 24 23 50 54 23 25 24 25 24 23 50 44 35 49 86 65 77 101 65 86 77 64 25 24 60 96 68 36 25 24 50 8 68 29 36 68 36 50 25 24 25 24 59 90 78 102 48 50 80 40 20 50 83 6 60 24 25 50.
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
デバイスProForm PFSY59001の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ProForm PFSY59001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはProForm PFSY59001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ProForm PFSY59001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ProForm PFSY59001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ProForm PFSY59001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はProForm PFSY59001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ProForm PFSY59001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちProForm PFSY59001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
