Proximメーカー5012-SURの使用説明書/サービス説明書
ページ先へ移動 of 24
Quick Install Guide T sunami MP .1 1 Model 5012-SUR V ersion 3.0.1 Part Number: 73226 (CD version) 73227 (Print version).
Page 2 Copyright © 2006 Proxim Wireless NOTICES Copyright Copyright ©2006 Proxim Wireless Corpor ation, San Jose, CA. All rights reserved. Covered b y one or more of the following U.S. patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753.
All rights reserved Page 3 CONTENTS Introduction ................................................................... 4 K ey Features ........................................................................................ 4 Package Contents ..........
Page 4 Copyright © 2006 Proxim Wireless INTRODUCTION The T sunami MP .11 Model 5012-SUR is a exible wireless outdoor client that let you design solutions for point-to-point links and point -to-multipoint networks. The 5012-SUR is part of the T sunami MP .
All rights reserved Page 5 P ACKAGE CONTENTS Each T sunami 5012-SUR shipment includes the items listed in the following table. V erify that y ou have received all parts of the shipment.
Page 6 Copyright © 2006 Proxim Wireless HARDW ARE AND SOFTW ARE INST ALLA TION Notes: Be sure to read the Release Notes le on the installation CD as it contains software version and driver information that ma y not have been available when this document was produced.
All rights reserved Page 7 Step 1: Choose a location T o make optimal use of the unit, y ou must nd a suitable location for the hardware. The range of the unit largely depends upon the position of the integrated antenna. Pro xim recommends you do a site survey , observing the following requirements, before mounting the hardware.
Page 8 Copyright © 2006 Proxim Wireless Step 2: Attach cables Note: Depending on your application and location, you ma y nd it easier to mount the unit before you attach cables to it. If this is the case, remov e the cable cover (as explained in step 1 below), and then complete Step 3: Mount Unit to Pole .
All rights reserved Page 9 a switch, hub, or patch panel. Use a cross-over Ethernet cable or adapter if y ou are connecting the unit to a single computer or most router ports.
Page 10 Copyright © 2006 Proxim Wireless Step 3: Mount Unit to Pole Mount the 5012-SUR to a pole as follows: Using a screwdriver , turn the screw on the band clamp counter-clockwise until the clamp opens. Place the back of the 5012-SUR against the pole such that the pole ts into the curved portion of the unit.
All rights reserved Page 1 1 Repeat procedure to attach other band clamp through bottom opening in the 5012-SUR unit. Note: Do not fully tighten band clamps; you must rst ensure a functional link to the BSU (Step 4: View LEDs/Adjust Mounting).
Page 12 Copyright © 2006 Proxim Wireless Step 4: View LEDs/Adjust Mounting LEDs are located in the cable compartment. When the unit is powered on, the 5012-SUR performs startup diagnostics. When startup is completed, the LEDs show the operational state of the 5012- SUR.
All rights reserved Page 13 Step 5: Close Cable Compartment Ensure that the Ethernet cable is properly routed and exiting the unit through the notch at the bottom of the cable compartment.
Page 14 Copyright © 2006 Proxim Wireless The assembly with the cable cover attached is shown below ..
All rights reserved Page 15 Step 6: Tighten Band Clamps Using a 5/16” nutdriver or a screwdriver , fully tighten both band clamps (maximum torque 50 kg-cm/3.6 lbf-ft). Secure Ethernet cable to the pole with cable ties. Provide some slack between the unit and the rst cable tie, which should be within 12 inches of the unit.
Page 16 Copyright © 2006 Proxim Wireless Step 7: Install Documentation and Software Place the CD in a CD-ROM drive. The installer normally starts automatically . (If the installation program does not start automatically , click setup.exe on the installation CD.
All rights reserved Page 17 INITIALIZA TION Connecting to the unit requires either: A direct physical connection with an Ethernet cable or with a serial RS-232 cable A network connection Connecting with the Ethernet cable allows you to use of the W eb Interface and SNMP in addition to the CLI.
Page 18 Copyright © 2006 Proxim Wireless Select the unit for which you want to set the IP address and click Change . The Change dialog window is displayed. T o set the IP address manually , ensure that Static is selected as the IP Address Type and ll in the IP Address and Subnet Mask suitable for the LAN subnet to which the unit is connected.
All rights reserved Page 19 Accessing the Web Browser T o access the unit with a W eb browser: Start your W eb browser and enter the IP address of the unit in the Address box. The W eb address should appear as http://<ip address> (for example, http://10.
Page 20 Copyright © 2006 Proxim Wireless Accessing the Command Line Interface Ethernet Port T o use the CLI through the Ethernet port, you must have a telnet progr am, the CLI password, and the unit’s IP address. T o access the unit through Ethernet on a Windows PC: Open a DOS command window: from the Windows Start menu, select Run ; enter cmd.
All rights reserved Page 21 DEF AUL T SETTINGS Setting Default Mode of Operation Bridge Routing Disabled IP Address Assignment Static IP Address 10.0.0.1 Subnet Mask 255.255.255.0 Default Router IP Address 10.0.0.1 Default T TL 64 RIPv2 (if in routing Mode) Enabled Base Station System Name <blank> Network Name OR_WORP Frequency Channel Chnl.
Page 22 Copyright © 2006 Proxim Wireless Setting Default Multi-Frame Bursting Enabled Storm Threshold Broadcast/Multicast Unlimited Broadcast Protocol Filtering All Protocols Allowed Dynamic Data Rat.
All rights reserved Page 23 TECHNICAL SERVICES AND SUPPORT If you are having trouble utilizing your Pro xim product, please review the Tsunami MP.11 5012-SUR Installation and Management Guide and the additional documentation provided with your product.
www .proxim.com 2115 O’Nel Drive San Jose, CA (408) 731-2700.
デバイスProxim 5012-SURの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Proxim 5012-SURをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはProxim 5012-SURの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Proxim 5012-SURの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Proxim 5012-SURで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Proxim 5012-SURを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はProxim 5012-SURの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Proxim 5012-SURに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちProxim 5012-SURデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。