PSCメーカー7000の使用説明書/サービス説明書
ページ先へ移動 of 212
PowerScan ® 7000 Linear Imager Product Reference Guide.
PSC Inc 959 T erry Street Eugene, Oregon 97402 T elephone: (541) 683-5700 F ax: (541) 345-7140 An Unpublished W ork - All r ights reserved. No par t of the contents of this documenta- tion or the procedures described therein may be reproduced or transmitted in an y fo r m or by any means without prior written per mission of PSC Inc.
Product Reference Guide i Table of Contents About This Manual ............................................................................ 1-1 Manual Conventions .................................................................... 1-2 Connecting the Scanner .
ii PowerScan ® 7000 Wand Idle State .................................................................. 3-34 Signal Speed ....................................................................... 3-36 Transmit Leading Noise .............................
Product Reference Guide iii Code 39 ........................................................................................ 5-30 Disable/Enable Code 39 ............................................................. 5-30 Check Character Calculation ...
iv PowerScan ® 7000 Code 93 Length 1, Length 2 Pr ogramming Instructions .................. 5-69 Code 93 Stitching ...................................................................... 5-70 Minimum Reads .............................................
Product Reference Guide 1-1 Chapter 1 Getting Started The P o werScan ® 7000 Linear I mager marks a new performance level for handheld scanners. I t delivers aggressive read rates and depths of field on 1D and stacked codes.
Getting Started 1-2 PowerScan ® 7000 Linear Imager Manual Conventions The symbols listed below ar e used in this manual to notify the reader of key issues or procedures that must be observed when using the scanner: Connecting the Scanner U se the appropriate instructions below to connect the scanner to the ter- minal, PC or other host device.
Connecting the Scanner Product Reference Guide 1-3 Figure 1 . RS-232 Serial Connection USB Connection — Connect the scanner to a USB port on the termi- nal/PC using the correct USB cable fo r the interface type you order ed. Ref ere nc e Figure 2 . Figure 2.
Getting Started 1-4 PowerScan ® 7000 Linear Imager Wand Emulation Connection — Connect the scanner to the appro- priated port on the terminal/PC usin g the correct cable for the interface typ e you orde red . Ref ere nce Figure 2 . IBM Connection — Connect the scanner to the IBM port on the ter- minal/PC using the correct IBM cable.
Product Reference Guide 2-1 Chapter 2 General Features Double Read Timeout The Double Read Timeout f eature sets a time limit that determines how much time must pass bef ore reading the same label again (e.g. two identical items in succes- sion). ST ART DURA TION BARCODE 0.
General Features 2-2 PowerScan ® 7000 Linear Imager Double Read Timeout — continued ST ART DURA TION BARCODE 0.5 Second 0.6 Second 0.7 Second 0.8 Second 0.
Powerdown Timeout Product Reference Guide 2-3 Powerdown Timeout The P owerdo wn Timeout feature sets the time f or automatically switching the unit off when the scanner is not in use.
General Features 2-4 PowerScan ® 7000 Linear Imager Powerdown Timeout — continued ST ART DURA TION BARCODE 3 Minutes 4 Minutes END.
LED and Beeper Indicators Product Reference Guide 2-5 LED and Beeper Indicators Power On Alert Disables or enables the indication (from the Beeper) that the scanner is receiving pow er .
General Features 2-6 PowerScan ® 7000 Linear Imager Good Read: When to Indicate This feature specifies when the scanner will pro vide indication (beep and/or flash its green LED) upon successfully reading a bar code.
LED and Beeper Indicators Product Reference Guide 2-7 Good Read Beep Control This feature enables/disables the scanner ’ s ability to beep upon a success- ful decode of a bar code.
General Features 2-8 PowerScan ® 7000 Linear Imager Good Read Beep Frequency Adjusts the good read beep to sound at a selectable lo w , medium or high frequency , selectable from the list below .
LED and Beeper Indicators Product Reference Guide 2-9 Good Read Beep Length S pecifies the duration of a good read beep. ST ART LENGTH BARCODE 60msec 80msec 100msec 120msec 140msec 160msec.
General Features 2-10 PowerScan ® 7000 Linear Imager Good Read Beep Length — continued ST ART LENGTH BARCODE 180msec 200msec END.
LED and Beeper Indicators Product Reference Guide 2-11 Good Read Beep Volume Selects the beeper volume (loudness) upon a good r ead beep. There are three selectable volume levels.
General Features 2-12 PowerScan ® 7000 Linear Imager Scanning Features Scan Mode Selects the scan operating mode for the scanner . Selections are: • Single — When the trigger is pull ed, scanning.
Scanning Features Product Reference Guide 2-13 Scan Mode — continued ST ART MODE BARCODE Single T rigger less Stand Stand w/Illum END.
General Features 2-14 PowerScan ® 7000 Linear Imager Active Scanning Time This setting determines the amount of time the scanner continues to scan in triggerless or stand mode (see Scan Mode ) once scanning has been activated.
Scanning Features Product Reference Guide 2-15 Active Scanning Time — continued ST ART DURA TION BARCODE 2 Minutes 3 Minutes 4 Minutes END.
General Features 2-16 PowerScan ® 7000 Linear Imager Laser Pointer Control When the trigger is pressed and Scan Mode is set to Single , the laser pointer will be activated for the time period configured by this featur e. Immediately follo wing this, the scan ner will star t scanning.
Scanning Features Product Reference Guide 2-17 Laser Pointer Control — continued ST ART DURA TION BARCODE 0.5 Seconds 0.6 Seconds 0.8 Seconds 1 Second 1.
General Features 2-18 PowerScan ® 7000 Linear Imager Laser Pointer Control — continued ST ART DURA TION BARCODE 2 Seconds 2.5 Seconds END.
Product Reference Guide 3-1 Chapter 3 Interface Related Features At the time of this writing, the Scan ner supports the interfaces listed in Ta b l e 3 - 1 . Select the desired interface type from the table, then r eference the page number given for the customizable features section associated with each interface.
Interface Related Features 3-2 PowerScan ® 7000 Linear Imager Table 3-1. Interfaces Supported RS-232 P age K eyboard W edge P age RS-232 Standard 3-10 K eyboard W edge H a RS-232 Wincor-Nixdorf 3-10 .
Product Reference Guide 3-3 Table 3-2. Keyboard Wedge Interface Reference I/F T ype PCs Supported A PC/XT w/Alternate Ke y Encoding B A T , PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alte.
Interface Related Features 3-4 PowerScan ® 7000 Linear Imager Interface Selection ST ART INTERF ACE BARCODE RS-232 Standard RS-232 Wincor-Nixdorf IBM 4683 Po r t 5 B IBM 4683 Po r t 9 B IBM 4683 Po r.
Interface Selection Product Reference Guide 3-5 Interface Selection — cont. ST ART INTERF ACE BARCODE K eyboard Wedge A K eyboard Wedge B K eyboard Wedge C K eyboard Wedge D K eyboard Wedge E K eybo.
Interface Related Features 3-6 PowerScan ® 7000 Linear Imager Interface Selection — cont. ST ART INTERF ACE BARCODE K eyboard Wedge H K eyboard Wedge I K eyboard W edge J K eyboard Wedge K K eyboar.
Interface Selection Product Reference Guide 3-7 Interface Selection — cont. ST ART INTERF ACE BARCODE K eyboard W edge O K eyboard Wedge P K eyboard W edge Q K eyboard Wedge R K eyboard Wedge S K ey.
Interface Related Features 3-8 PowerScan ® 7000 Linear Imager Interface Selection — cont. Interface Features ST ART INTERF ACE BARCODE K eyboard Wedge U K eyboard Wedge V K eyboard Wedge W K eyboar.
Interface Features Product Reference Guide 3-9 Global Interface Features ST ART ST A TE BARCODE Obey Host Commands Ignore Host Commands Host T ransmission Buffers = 1 Host T ransmission Buffers = 2 EN.
Interface Related Features 3-10 PowerScan ® 7000 Linear Imager RS-232 Interface Features ST ART BA UD RA TE BARCODE 1200 Baud 2400 Baud 4800 Baud 9600 Baud 19200 Baud 38400 Baud.
Interface Features Product Reference Guide 3-11 RS-232 Interface Features — cont. ST ART BA UD RA TE BARCODE 57600 Baud 115200 Baud END.
Interface Related Features 3-12 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. ST ART ST A TE BARCODE 7 Data Bits 8 Data Bits 1 Stop Bit 2 Stop Bits Parity = None.
Interface Features Product Reference Guide 3-13 RS-232 Interface Features — cont. ST ART ST A TE BARCODE P arity = Even P arity = Odd END.
Interface Related Features 3-14 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. Hardware Flow Control Di sa b l e Ha rdw a re C on t ro l — The scanner transmits to the host regard less of any activity on the CTS line. Enable CT S Flow Control — The CTS signal controls transmission of data to the host.
Interface Features Product Reference Guide 3-15 RS-232 Interface Features — cont. ST ART ST A TE BARCODE Disable Hard ware Control Enable CTS Flow Control Enable CTS Scan Control Inter-Char Delay = .
Interface Related Features 3-16 PowerScan ® 7000 Linear Imager Interchar Delay = 30 msec Interchar Delay = 40 msec Interchar Delay = 50 msec Interchar Delay = 60 msec Interchar Delay = 70 msec Interchar Delay = 80 msec RS-232 Interface Features — cont.
Interface Features Product Reference Guide 3-17 Interchar Delay = 90 msec Disable Software Flow Control Enable Software Flow Control END RS-232 Interface Features — cont.
Interface Related Features 3-18 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. Host Echo When enabled, this feature passes all data through the scanner to the host as it comes in. This feature is used for applications where “ daisy chaining” of RS-232 devices onto the same cable is necessary .
Interface Features Product Reference Guide 3-19 RS-232 Interface Features — cont. ST ART ST A TE BARCODE Disable Host Echo Enable Host Echo Host Echo Quiet Interval = 0msec Host Echo Quiet Interval .
Interface Related Features 3-20 PowerScan ® 7000 Linear Imager Host Echo Quiet Interval = 40msec Host Echo Quiet Interval = 50msec Host Echo Quiet Interval = 60msec Host Echo Quiet Interval = 70msec Host Echo Quiet Interval =80msec Host Echo Quiet Interval = 90msec Host Echo Quiet Interval = 100msec RS-232 Interface Features — cont.
Interface Features Product Reference Guide 3-21 Beep on ASCII BEL Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL (07 hex). Beep on Not on File Select for the host to beep (or not) when a not-on-file (host command) condition is detected by the host.
Interface Related Features 3-22 PowerScan ® 7000 Linear Imager ACK NAK Options This enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol. When configur ed, the scanner and/or host sends an “ ACK” when it r eceives data properly , and sends “NAK” when the data is in error .
Interface Features Product Reference Guide 3-23 ACK NAK Options — cont. ST ART ST A TE BARCODE Disable A C K NAK Enable A CK NAK for T ransmission Enable A CK NAK for host- command ackno wledge Enab.
Interface Related Features 3-24 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. ACK Character ST ART MODE BARCODE Sets the ACK char acter from the set of ASCII charac- ters or any decimal v alue from 000 to 255. Pad entries of less than three digits with zeros, as in “005”.
Interface Features Product Reference Guide 3-25 RS-232 Interface Features — cont. NAK Character ST ART MODE BARCODE Sets the NAK character from the set of ASCII charac- ters or any decimal v alue from 000 to 255. Pad entries of less than three digits with zeros, as in “005”.
Interface Related Features 3-26 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. Retry on ACK NAK Timeout Enables/disables retry after the configurable ACK NAK T imeout V alue (set in the following feature) has expir ed.
Interface Features Product Reference Guide 3-27 RS-232 Interface Features — cont. ACK NAK Timeout Value ST ART MODE BARCODE This item specifies the time the scanner will wait f or an ACK char acter from the host following a label transmission.
Interface Related Features 3-28 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. ACK NAK Retry Count ST ART MODE BARCODE This feature sets the n umber of times for the scanner to retr y a label transmission under a retry condition.
Interface Features Product Reference Guide 3-29 RS-232 Interface Features — cont. ACK NAK Error Handling This item specifies the method the scanner will use to handle errors detected while waiting to receive the A CK character from the host. Errors include unr ecognized host commands and communication errors such as parity or framing errors.
Interface Related Features 3-30 PowerScan ® 7000 Linear Imager RS-232 Interface Features — cont. Transmission Failure Indication Enables/disables bad-label indication upon transmission failure.
Interface Features Product Reference Guide 3-31 IBM-USB Interface Features IBM-USB Device usage The IBM-USB protocol allows for the sc anner to be identified as one of two different types of bar code scanners.
Interface Related Features 3-32 PowerScan ® 7000 Linear Imager IBM IBM Transmit Labels in Code 39 Format This feature enables/disables scanner's ability to set a symbol- ogy identifier for a specified label to Code 39 before transmit- ting that label data to an IBM host.
Interface Features Product Reference Guide 3-33 Wand Emulation Supported Symbologies The W and Emulation interface will transmit bar code data as a wand device would.
Interface Related Features 3-34 PowerScan ® 7000 Linear Imager Wand Emulation — cont. Bar/Space Polarity Low/H igh — Black will be transmitted as a low voltage lev el (0 to +0.7V) and space as high level (+2.4 to +5.25V). High/Lo w — Black will be transmitted as a high voltage level (+2.
Interface Features Product Reference Guide 3-35 Wand Emulation — cont. ST ART ST A TE BARCODE W and Idle State = Low W and Idle State = High END.
Interface Related Features 3-36 PowerScan ® 7000 Linear Imager Wand Emulation — cont. Signal Speed The speed of the transmission can be set. This selects the width of the minimum narrow bar .
Interface Features Product Reference Guide 3-37 Wand Emulation — cont. Transmit Leading Noise The transmission of noise pulses before the bar code may be enabled or disabled.
Interface Related Features 3-38 PowerScan ® 7000 Linear Imager Symbology Conversion W and Emulation can convert all bar codes to a single symbology . Choices are: No C o n v e r s i o n Convert to Co.
Interface Features Product Reference Guide 3-39 Symbology Conversion — cont. ST ART ST A TE BARCODE Conv er t to C39 Conv er t to C128 END.
Interface Related Features 3-40 PowerScan ® 7000 Linear Imager Keyboard Wedge/USB Keyboard As a keyboard interface, the scanner supports most popular PCs and IBM terminals. The installation of th e wedge is a fairly simple process that doesn ’ t require any changes of softwar e or hardware.
Interface Features Product Reference Guide 3-41 Keyboard Wedge/USB Keyboard — cont. ST ART ST A TE BARCODE F rance Germany Italy Norwa y P or tugal Spain Sweden.
Interface Related Features 3-42 PowerScan ® 7000 Linear Imager Keyboard Wedge/USB Keyboard — cont. ST ART ST A TE BARCODE Switzerland Japan 106 K ey Hungary Czech Slov akia Romania.
Interface Features Product Reference Guide 3-43 Keyboard Wedge/USB Keyboard — cont. ST ART ST A TE BARCODE Croatia P oland END.
Interface Related Features 3-44 PowerScan ® 7000 Linear Imager Keyboard Wedge/USB Keyboard — cont. Caps Lock State S pecifies which format the scanner sends character data.
Interface Features Product Reference Guide 3-45 Keyboard Wedge/USB Keyboard — cont. Keyboard Simulation All PCs check the keyboard status during the po wer-on Selftest. I t is rec- ommended that you enable this function if you are working without a keyboard installation.
Interface Related Features 3-46 PowerScan ® 7000 Linear Imager Keyboard Wedge/USB Keyboard — cont. ST AR T ST A TE BARCODE Disable Keyboar d Simulation Enable Keyboar d Simulation Disable Control C.
Interface Features Product Reference Guide 3-47 Keyboard Wedge/USB Keyboard — cont. Wedge Quiet Interval Quiet Interval is the amount of time to look for keyboard activity before the scanner breaks the keyboar d connection in order to transmit data to the host.
Interface Related Features 3-48 PowerScan ® 7000 Linear Imager Keyboard Wedge/USB Keyboard — cont. Intercharacter Delay NO TE This feature does not apply to the USB K eyboard interface. ST ART MODE BARCODE One-half of the dela y specified below is inser ted between scancodes within each character .
Product Reference Guide 4-1 Chapter 4 Data Editing Data Editing Overview When a bar code is scanned, addition al information can be sent to the host computer along with the bar code data. This combination of bar code data and supplementary user-defined data is called a “ message string.
Data Editing 4-2 PowerScan ® 7000 Linear Imager Please Keep In Mind... • M odifying a message string is not a mandator y requirement. Data editing is sophisticated feature allo wing highly customizable out- put for advanced users. F actor y default settings for data editing is typically set to NONE.
Global Prefix/Suffix Product Reference Guide 4-3 Global Prefix/Suffix — continued Example: Setting a Prefix In this example, we ’ll set a prefix for all symbologies. 1. Determine which ASCII character(s) are to be added to scanned bar code data. In this example, we ’ ll add a dollar sign (‘$’) as a pre- fix.
Data Editing 4-4 PowerScan ® 7000 Linear Imager Global Prefix/Suffix — continued ST ART MODE BARCODE Sets up to 20 characters each from the set of ASCII characters or any he x value from 0 to FF .
AIM ID Product Reference Guide 4-5 AIM ID AIM label identifiers (as opposed to custom characters you select your- self as with label identifiers) can be included with scanned bar code data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed b y .
Data Editing 4-6 PowerScan ® 7000 Linear Imager AIM ID — continued ST ART ST A TE BARCODE Disable AIM ID Enable AIM ID END.
Label ID Product Reference Guide 4-7 Label ID A Label ID is a customizable code of up to two ASCII characters (00- FF), used to identify a bar code (s ymbology) type. I t can be appended previous to or following the transmitted bar code data depending upon how this option is enabled.
Data Editing 4-8 PowerScan ® 7000 Linear Imager Label ID — continued ST ART OPTION BARCODE Label ID T ransmission: Disable Label ID P osition: Before Bar Code Data Label ID P osition: After Bar Cod.
Label ID Product Reference Guide 4-9 Label ID — continued ST ART OPTION BARCODE Set UPC-A w/C128 Addon Label ID Character(s) DEF AUL T SETTING FOR THIS FEA TURE: A (41 hex) Set UPC-E Label ID Charac.
Data Editing 4-10 PowerScan ® 7000 Linear Imager Label ID — continued ST ART OPTION BARCODE Set EAN-8 w/P5 Addon Label ID Character(s) DEF AUL T SETTING FOR THIS FEA TURE: FF (4646 hex) Set EAN-8 w.
Label ID Product Reference Guide 4-11 Label ID — continued ST ART OPTION BARCODE Set GTIN Label ID Character(s) DEF A UL T SETTING FOR THIS FEA TURE: G (47 hex) Set GTIN w/P2 addon Label ID Characte.
Data Editing 4-12 PowerScan ® 7000 Linear Imager Label ID — continued ST ART OPTION BARCODE Set RSS Expanded Label ID Character(s) DEF AUL T SETTING FOR THIS FEA TURE: RX (5258 hex) Set Code 39 Lab.
Label ID Product Reference Guide 4-13 Label ID — continued ST ART OPTION BARCODE Set Codabar Label ID Character(s) DEF AUL T SETTING FOR THIS FEA TURE: % (25 hex) Set Code 93 Label ID Character(s) D.
Data Editing 4-14 PowerScan ® 7000 Linear Imager Case Conversion This feature can convert scanned bar code data to either all lower case or all upper case characters. NO TE Case con version affects ONL Y scanned bar code data, and does not affect Label ID , Prefix, Suffix, or other appended data.
Label ID Product Reference Guide 4-15 Character Conversion Character conversion is an eight by te configuration item. The eight bytes are 4 character pairs r epresented in hexadecimal ASCII values. The first character in the pair is the character that will be converted.
Data Editing 4-16 PowerScan ® 7000 Linear Imager Character Conversion — continued ST ART MODE BARCODE Character Conv ersion DEF A UL T SETTING FOR THIS FEA TURE: FFFFFFFFFFFFFFFF hex (no con versio.
Product Reference Guide 5-1 Chapter 5 Symbologies The scanner supports the following symbologies (bar code types). Options for each symbology are included in this chapter . Factory Defaults — are indicated in bold text and are highlighted with yellow thr oughout this section.
Symbologies 5-2 PowerScan ® 7000 Linear Imager UPC-A The following options apply to the UPC-A symbology . Disable/Enable UPC-A When disabled, the scanner will not read UPC-A bar codes. Check Digit Transmission Enable this option to transmit the check digit along with UPC-A bar code data.
UPC-A Product Reference Guide 5-3 UPC-A — continued ST ART ST A TE BARCODE Disable UPC-A Enable UPC-A Don’t Send Check Digit Send Check Digit Don’t Expand to EAN-13 Expand to EAN-13.
Symbologies 5-4 PowerScan ® 7000 Linear Imager UPC-A — continued ST ART ST A TE BARCODE Disable Sys- tem Number T ransmission Enable System Number T rans- mission END.
UPC-A Product Reference Guide 5-5 UPC-A — continued UPC-A Minimum Reads This feature specifies the minimum number of consecutive times a UPC- A label must be decoded before it is accepted as good read.
Symbologies 5-6 PowerScan ® 7000 Linear Imager UPC-A — continued In-store Minimum Reads This feature specifies the minimum number of consecutive times an in- store printed label must be decoded be fore it is accepted as good r ead.
UPC-A Product Reference Guide 5-7 UPC-A — continued ST ART ST A TE BARCODE This item is used to set the timer value when optional add-ons are enabled. The selectab le range is from 10 to 300 mSec in 10 mSec increments and is entered in hex (01-0x1E b y 01).
Symbologies 5-8 PowerScan ® 7000 Linear Imager UPC-E The following options apply to the UPC-E symbology . Disable/Enable UPC-E When disabled, the scanner will not read UPC-E bar codes. Check Digit Transmission Enable this option to transmit the check digit along with UPC-E bar code data.
UPC-E Product Reference Guide 5-9 UPC-E — continued ST ART ST A TE BARCODE Disable UPC-E Enable UPC-E Don’t Send Check Digit Send Check Digit Exclude Sys- tem Number Include System Number.
Symbologies 5-10 PowerScan ® 7000 Linear Imager Don’t Expand UPC-E to UPC-A Expand UPC-E to UPC-A Don’t Expand UPC-E to EAN-13 Expand UPC-E to EAN-13 END UPC-E — continued ST ART ST A TE BARCOD.
UPC-E Product Reference Guide 5-11 UPC-E — continued Minimum Reads This feature specifies the minimum number of consecutive times a UPC- E label must be decoded before it is accepted as good read.
Symbologies 5-12 PowerScan ® 7000 Linear Imager GTIN The following options apply to the GTIN label data format. Disable/Enable GTIN When this feature is enabled, the scanner will translate UPC/EAN labels to the 14 digit GTIN format.
EAN-13 Product Reference Guide 5-13 EAN-13 The following options apply to the EAN-13 symbology . Disable/Enable EAN-13 When disabled, the scanner will not read EAN-13 bar codes. Check Digit Transmission Enable this option to transmit the check digit along with EAN-13 bar code data.
Symbologies 5-14 PowerScan ® 7000 Linear Imager EAN-13 — continued ST ART ST A TE BARCODE Disable EAN-13 Enable EAN-13 Don’t Send Check Digit Send Check Digit Don’t T ransmit EAN-13 Flag 1 Char.
EAN-13 Product Reference Guide 5-15 Disable ISBN Enable ISBN END EAN-13 — continued ST ART ST A TE BARCODE.
Symbologies 5-16 PowerScan ® 7000 Linear Imager EAN-13 — continued Minimum Reads This feature specifies the minimum number of consecutive times an EAN-13 label must be decoded before it is accepted as good read.
EAN-8 Product Reference Guide 5-17 EAN-8 The following options apply to the EAN-8 symbology . Disable/Enable EAN-8 When disabled, the scanner will not read EAN-8 bar codes. Check Digit Transmission Enable this option to transmit th e check Digit along with EAN-8 bar code data.
Symbologies 5-18 PowerScan ® 7000 Linear Imager EAN-8 — continued Expand EAN-8 to EAN-13 — Expands EAN-8 data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
EAN-8 Product Reference Guide 5-19 EAN-8 — continued Minimum Reads This feature specifies the minimum number of consecutive times an EAN-8 label must be decoded before it is accepted as good read.
Symbologies 5-20 PowerScan ® 7000 Linear Imager Add-ons Add-ons (or supplemental characters ) are commonly added to the end of UPC/EAN bar codes. The scanner wi ll read the add-ons if they are enabled and in the field of view . Three add-on types are supported: 2- digit, 5-digit and Code 128 add-ons.
Add-ons Product Reference Guide 5-21 Add-ons — continued ST ART ST A TE BARCODE Disable Optional 2- Digit Add-ons Enable Optional 2-Digit Add-ons Disable Optional 5- Digit Add-ons Enable Optional 5-.
Symbologies 5-22 PowerScan ® 7000 Linear Imager RSS-14 The following options apply to the RSS-14 symbology . Disable/Enable RSS-14 When this feature is disabled, the scanner will not read RSS-14 bar codes. UCC/EAN 128 Emulation When enabled, RSS-14 bar codes will be translated to the UCC/EAN 128 label data format.
RSS-14 Product Reference Guide 5-23 RSS-14 — continued ST ART ST A TE BARCODE Disable RSS-14 Enable RSS-14 Disable UCC/EAN 128 Emulation Enable UCC/EAN 128 Emulation END.
Symbologies 5-24 PowerScan ® 7000 Linear Imager RSS-14 — continued Minimum Reads This feature specifies the minimum number of consecutive times an RSS-14 label must be decoded before it is accepted as good read.
RSS Expanded Product Reference Guide 5-25 RSS Expanded The following options apply to the RSS Expanded symbology . Disable/Enable RSS Expanded When this feature is disabled, the scanner will not read RSS E xpanded bar codes. UCC/EAN 128 Emulation When enabled, RSS Expanded bar codes will be translated to the UCC/ EAN 128 label data format.
Symbologies 5-26 PowerScan ® 7000 Linear Imager RSS Expanded — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
RSS Expanded Product Reference Guide 5-27 RSS Expanded — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Symbologies 5-28 PowerScan ® 7000 Linear Imager RSS Expanded — continued RSS Expanded Length 1, Length 2 Pro- gramming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
RSS Expanded Product Reference Guide 5-29 RSS Expanded — continued Minimum Reads This feature specifies the minimum number of consecutive times an RSS Expanded label must be decoded before it is accepted as good r ead.
Symbologies 5-30 PowerScan ® 7000 Linear Imager Code 39 The following options apply to the Code 39 symbology . Disable/Enable Code 39 When this feature is disabled, the scanner will not read Code 39 bar codes. Check Character Calculation When enabled, the scanner will ca lculate the check character of the labels.
Code 39 Product Reference Guide 5-31 Code 39 — continued ST ART ST A TE BARCODE Disable Code 39 Enable Code 39 Disable Check Char Calculation Enable Check Char Calculation Disable Check Char T ransm.
Symbologies 5-32 PowerScan ® 7000 Linear Imager Code 39 — continued ST ART ST A TE BARCODE Don’t T ransmit Start/Stop Characters T ransmit Star t/Stop Characters Disable Code 39 Full ASCII Enable.
Code 39 Product Reference Guide 5-33 Code 39 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Symbologies 5-34 PowerScan ® 7000 Linear Imager Code 39 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Code 39 Product Reference Guide 5-35 Code 39 Length 1, Length 2 Programming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Symbologies 5-36 PowerScan ® 7000 Linear Imager Code 39 — continued Quiet Zones This feature enables/disables the requir ement that quiet zones must be present for Code 39 bar codes.
Code 39 Product Reference Guide 5-37 Code 39 — continued Code 39 Stitching Enables/disables stitching for Code 39 labels. When parts of a Code 39 bar code are presented to the scanner with this feat.
Symbologies 5-38 PowerScan ® 7000 Linear Imager Code 39 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Code 39 label must be decoded before it is accepted as good read.
Pharmacode 39 Product Reference Guide 5-39 Pharmacode 39 The following options apply to the Pharmacode 39 symbology . Disable/Enable Pharmacode 39 When this feature is disabled, the scanner will not read P harmacode 39 bar codes.
Symbologies 5-40 PowerScan ® 7000 Linear Imager Pharmacode 39 — continued Start/Stop Characters Enables or disables transmission of Pharmacode 39 start/stop characters. Check Character Transmit Enable this option to transmit the check character with scanned bar code data.
Code 128 Product Reference Guide 5-41 Code 128 The following options apply to the Code 128 symbology . Disable/Enable Code 128 When this feature is disabled, the scanner will not read Code 128 bar codes.
Symbologies 5-42 PowerScan ® 7000 Linear Imager Code 128 — continued Transmit Function Characters Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
Code 128 Product Reference Guide 5-43 Code 128 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Symbologies 5-44 PowerScan ® 7000 Linear Imager Code 128 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Code 128 Product Reference Guide 5-45 Code 128 — continued Code 128 Length 1, Length 2 Programming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Symbologies 5-46 PowerScan ® 7000 Linear Imager Code 128 — continued Code 128 Stitching Enables/disables stitching for Code 128 labels. When parts of a Code 128 bar code are presented to the scanne.
Code 128 Product Reference Guide 5-47 Code 128 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Code 128 label must be decoded before it is accepted as good read.
Symbologies 5-48 PowerScan ® 7000 Linear Imager Interleaved 2 of 5 The following options apply to the I nte rleaved 2 of 5 (I 2 of 5) symbol- ogy . Disable/Enable Interleaved 2 of 5 When this feature is disabled, the scanner will not read I nterleaved 2 of 5 bar codes.
Interleaved 2 of 5 Product Reference Guide 5-49 Interleaved 2 of 5 — continued ST ART ST A TE BARCODE Disable Interleaved 2 of 5 Enable Interleaved 2 of 5 Disable Check Digit Calculation Enable Chec.
Symbologies 5-50 PowerScan ® 7000 Linear Imager Interleaved 2 of 5 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Interleaved 2 of 5 Product Reference Guide 5-51 Interleaved 2 of 5 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Symbologies 5-52 PowerScan ® 7000 Linear Imager Interleaved 2 of 5 — continued Interleaved 2 of 5 Length 1, Length 2 Pro- gramming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation .
Interleaved 2 of 5 Product Reference Guide 5-53 Interleaved 2 of 5 Stitching Enables/disables stitching for Interleav ed 2 of 5 labels. When parts of an Interleaved 2 of 5 bar code ar e presented to t.
Symbologies 5-54 PowerScan ® 7000 Linear Imager Interleaved 2 of 5 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Interleaved 2 of 5 label must be deco ded before it is accepted as good read .
Codabar Product Reference Guide 5-55 Codabar The following options apply to the Codabar symbology . Disable/Enable Codabar When this feature is disabled, the scanner will not read Codabar bar codes. Check Character Verification When enabled, the scanner will verify the check character of the labels.
Symbologies 5-56 PowerScan ® 7000 Linear Imager Codabar — continued ST ART ST A TE BARCODE Disable Codabar Enable Codabar Disable Check Char V erification Enable Check Char V erification Disable Ch.
Codabar Product Reference Guide 5-57 Codabar — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Symbologies 5-58 PowerScan ® 7000 Linear Imager Codabar — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Codabar Product Reference Guide 5-59 Codabar — continued Codabar Length 1, Length 2 Programming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Symbologies 5-60 PowerScan ® 7000 Linear Imager Codabar — continued Quiet Zones This feature enable/disables the requir ement that quiet zones must be present for Codabar bar codes.
Codabar Product Reference Guide 5-61 Codabar — continued Start/Stop Character Type Codabar has four pairs of St art/Stop patterns. Select one pair to match your application. Start/Stop Character Transmission The transmission of start and end characters of Codabar is selected below .
Symbologies 5-62 PowerScan ® 7000 Linear Imager Codabar — continued ST ART ST A TE BARCODE Star t/Stop T ype: ABCD/ TN*E Star t/Stop T ype: ABCD/ ABCD Star t/Stop T ype: abcd/tn*e Start/Stop T ype:.
Codabar Product Reference Guide 5-63 Codabar — continued ST ART ST A TE BARCODE Disable Start/Stop Char Match Enable Star t/Stop Char Match END.
Symbologies 5-64 PowerScan ® 7000 Linear Imager Codabar — continued Codabar Stitching Enables/disables stitching for Codabar labels. When parts of a Codabar label are presented to the scanner with .
Codabar — continued Product Reference Guide 5-65 Codabar — continued Minimum Reads This feature specifies the minimum number of consecutive times an Codabar label must be decoded before it is accepted as good read.
Symbologies 5-66 PowerScan ® 7000 Linear Imager Code 93 The following options apply to the Code 93 symbology . Disable/Enable Code 93 When this feature is disabled, the scanner will not read Code 93 bar codes.
Code 93 Product Reference Guide 5-67 Code 93 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Symbologies 5-68 PowerScan ® 7000 Linear Imager Code 93 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Code 93 Product Reference Guide 5-69 Code 93 — continued Code 93 Length 1, Length 2 Programming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Symbologies 5-70 PowerScan ® 7000 Linear Imager Code 93 — continued Code 93 Stitching Enables/disables stitching for Code 93 bar codes. When parts of a Code 93 label are presented to the scanner wi.
Code 93 Product Reference Guide 5-71 Code 93 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Code 93 label must be decoded before it is accepted as good read.
Symbologies 5-72 PowerScan ® 7000 Linear Imager MSI/Plessey The following options apply to the MSI/Plessey symbology . Disable/Enable MSI/Plessey When this feature is disabled, the scanner will not read MSI/P lessey bar codes. Check Digit Verification This feature specifies whether one or two check digits are to be calcu- lated and verified.
MSI/Plessey Product Reference Guide 5-73 MSI/Plessey — continued ST ART ST A TE BARCODE Disable MSI/Plessey Enable MSI/Plessey Disable Check Digit V erification Enable Check Digit V erification 1-Di.
Symbologies 5-74 PowerScan ® 7000 Linear Imager Disable Check Digit T ransmission Enable Check Digit T ransmission END MSI/Plessey — continued ST ART ST A TE BARCODE.
MSI/Plessey Product Reference Guide 5-75 MSI/Plessey — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Symbologies 5-76 PowerScan ® 7000 Linear Imager MSI/Plessey — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
MSI/Plessey Product Reference Guide 5-77 MSI/Plessey — continued MSI/Plessey Length 1, Length 2 Program- ming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Symbologies 5-78 PowerScan ® 7000 Linear Imager MSI/Plessey — continued MSI/Plessey Stitching Enables/disables stitching for MSI/Plessey bar codes. When parts of an MSI/Plessey label are pr esented.
MSI/Plessey Product Reference Guide 5-79 MSI/Plessey — continued Minimum Reads This feature specifies the minimum number of consecutive times an MSI/Plessey label must be decoded before it is accepted as good r ead.
Symbologies 5-80 PowerScan ® 7000 Linear Imager Standard 2 of 5 The following options apply to the S tandard 2 of 5 symbology . Disable/Enable Standard 2 of 5 When this feature is disabled, the sc anner will not read S tandard 2 of 5 bar codes. Check Digit Verification When enabled, the scanner will veri fy the check digit of the labels.
Standard 2 of 5 Product Reference Guide 5-81 Standard 2 of 5 — continued ST ART ST A TE BARCODE Disable Std 2 of 5 Enable Std 2 of 5 Disable Check Digit V erification Enable Check Digit V erificatio.
Symbologies 5-82 PowerScan ® 7000 Linear Imager Standard 2 of 5 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Standard 2 of 5 Product Reference Guide 5-83 Standard 2 of 5 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Symbologies 5-84 PowerScan ® 7000 Linear Imager Standard 2 of 5 — continued Standard 2 of 5 Length 1, Length 2 Pro- gramming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
Standard 2 of 5 Product Reference Guide 5-85 Standard 2 of 5 — continued Standard 2 of 5 Stitching Enables/disables stitching for S tandard 2 of 5 bar codes.
Symbologies 5-86 PowerScan ® 7000 Linear Imager Standard 2 of 5 — continued Minimum Reads This feature specifies the minimum number of consecutive times a S tan- dard 2 of 5 label must be decoded befor e it is accepted as good read.
PDF 417 Product Reference Guide 5-87 PDF 417 The following options apply to the PDF 417 symbology . Disable/Enable PDF 417 When this feature is disabled, the scanner will not read PDF 417 bar codes.
Symbologies 5-88 PowerScan ® 7000 Linear Imager PDF 417 — continued Length Control Fixed Length Decoding — When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
PDF 417 Product Reference Guide 5-89 PDF 417 — continued ST ART MODE BARCODE Va r i a b l e Length Decoding Fixed Length Decoding END.
Symbologies 5-90 PowerScan ® 7000 Linear Imager PDF 417 — continued PDF 417 Length 1, Length 2 Programming Instructions 1. Scan the ST AR T bar code. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Appendix C, Alpha-Numeric P ad and scan the two digits rep- resenting the length in decimal notation.
PDF 417 Product Reference Guide 5-91 PDF 417 — continued Minimum Reads This feature specifies the minimum number of consecutive times a PDF 417 label must be decoded before it is accepted as good read.
Symbologies 5-92 PowerScan ® 7000 Linear Imager NOTES.
Product Reference Guide A-1 Appendix A Product Specifications Optical and Read Performance Parameters Parameter Specification Scanning Width 2” wide at 1” from scanner 6” wide at 7” from scanner Minimum Resolution 4mil minimum element size (at some distance, no implied DOF) Depth of Field (75% read rate; 90% PCS; Code 39 with 2.
A-2 PowerScan ® 7000 Linear Imager Physical Properties Electrical Parameters Parameter Specification Dimensions (T ypical): Height 7.5”/190 mm Length 4.
Environmental Parameters Product Reference Guide A-3 Environmental Parameters Other Parameters Parameter Specification Mechanical Shock 50 drops from 6.
A-4 PowerScan ® 7000 Linear Imager NOTES.
Product Reference Guide B-1 Appendix B Cable Pinouts Standard Cable Pinouts (Primary Interface Cables) RS-232 IBM Port 5B/9B/17 1 2C T S 3 4R T S 5 RXD 6T X D 7 8V C C I N 9G N D 10 Cable Select 1 2 3.
Cable Pinouts B-2 PowerScan ® 7000 Linear Imager IBM USB USB & USB Keyboard Wand Emulation 1 2 3 4D - 5 6D + 7 8V I N 9G N D 10 1 2 3 4D - 5 6D + 7 8 VBUS_VIN 9G N D 10 1 2 3 W AND~ 4 5 6 7 8 VCC.
Standard Cable Pinouts (Primary Interface Cables) Product Reference Guide B-3 Keyboard Wedge 1 2 KB_D A T A 3 A T_CLK 4 KB_CLK 5 6 A T_D A T A 7 8V C C _ I N 9G N D 10 Pin 1 10 Position RJ (Scanner En.
Cable Pinouts B-4 PowerScan ® 7000 Linear Imager NOTES.
Product Reference Guide C-1 Appendix C Alpha-Numeric Pad A B C D E F.
C-2 PowerScan ® 7000 Linear Imager Alpha-Numeric Pad 1 2 3 0 9 8 7 6 5 4.
Product Reference Guide D-1 Appendix D Default Settings Defaults by Symbology The following is a partial list of ke y settings for each symbology type.
D-2 PowerScan ® 7000 Linear Imager Interface Default Exceptions The factory default settings indicated in the programming sections (by bold text and yellow highlighting) reflect factory configuration for the RS-232 standard interface. The following tables list default ex ceptions by interface for the remaining available interfaces.
Interface Default Exceptions Product Reference Guide D-3 RS-232 Wincor/Nixdorf Parameter Default Setting Interface T ype RS-232-WN Number of Host T ransmit Buff ers One Buff er RS-232 P arity Odd RS-2.
D-4 PowerScan ® 7000 Linear Imager Keyboards Keyboard interfaces include USB Keyboard and Keyboar d W edge A-Y. Parameter Default Setting K eyboard W edge Interface T ype USB K eyboard Label ID T ran.
Product Reference Guide E-1 Appendix E Keyboard Function Key Mappings Keyboard Model Cross Reference Ta b l e E - 2 summarizes the keyboard models, their defined protocol, scancode set, and some unique features. The remaining tables in this chapter pro vide the function key maps associated with each of the scan- code sets.
E-2 PowerScan ® 7000 Linear Imager Table E-1. Keyboard Model Cross Reference Model T ype I/F ID T rans- mission Protocol Scancode Set Func. Key Map Support Use Country Mode PC/XT Foreign AL T Mode W .
Keyboard Model Cross Reference Product Reference Guide E-3 Table E-2. Scanset 1 Function Key Map ASCII (hex) ASCII code K ey Scancode 00 NUL AL T right Make E0h 38h 01 SOH AL T right Break E0h B8h 02 .
E-4 PowerScan ® 7000 Linear Imager Table E-3. Scanset 2 Function Key Map ASCII (hex) ASCII code K ey Scancode 00 NUL AL T right Make E0h 11h 01 SOH AL T right Break E0h F0h 11h 02 STX AL T left Make .
Keyboard Model Cross Reference Product Reference Guide E-5 Table E-4 . Scanset 3, 102-Key Function Key Map ASCII (hex) ASCII code Key Scancode 00 NUL AL T r ight Make 39h 01 SOH AL T right Break F0h 3.
E-6 PowerScan ® 7000 Linear Imager Table E-5. Scanset 3 122-Key Function Key Map ASCII (hex) ASCII code Key Scancode 00 NUL AL T Right Make 39h 01 SOH AL T Right Break F0h 39h 02 STX AL T left Make 1.
Keyboard Model Cross Reference Product Reference Guide E-7 Table E-6. Japanese DOS Function Key Map ASCII value ASCII code Key Scancode 00h NUL AL T right Make 31h 01h SOH AL T right Break B1h 02h STX.
E-8 PowerScan ® 7000 Linear Imager Table E-7. NEC 9801-Key Function Key Map ASCII value ASCII code Key Scancode 00h NUL unused n/a 01h SOH CR 1Ch 02h STX CAPS LOCK ON (make) 71h 03h ETX CAPS LOCK OFF.
Product Reference Guide F-1 Appendix F Host Commands Accepting RS-232 Commands The scanner responds to the following RS-232 commands: If one of the abo ve commands is received, the scanner will perform the steps indicated for the command. Host commands for other interfaces is also available.
F-2 PowerScan ® 7000 Linear Imager NOTES.
Product Reference Guide G-1 Appendix G Sample Symbols 0 123456 7890 1234567890 Code 128 9 780330 290951 BC321 123456-9$ 123456 UPC-A Code 128 Code 39 Code 93 Interleaved 2 of 5 EAN-13 Code 2 of 5 A135.
G-2 PowerScan ® 7000 Linear Imager Sample Symbols (01)00123456789012 Car Registration PDF417 RSS-14 0100123456789050 RSS Expanded.
ASCII Char t ASCII Char . He x No. ASCII Char . Hex No . ASCII Char . Hex No . ASCII Char . He x No . NUL SOH STX ETX EO T ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SU.
Asia P acific PSC Hong K ong Hong K ong T elephone: [852]-2-584-6210 F ax: [852]-2-521-0291 Au s t r a l i a PSC Asia P acific Pty Ltd. Nor th Ryde, A ustralia T elephone: [61] 0 (2) 9878 8999 F ax: [61] 0 (2) 9878 8688 France PSC S.A.R.L. LES ULIS Cedex, F rance T elephone: [33].
デバイスPSC 7000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
PSC 7000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPSC 7000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。PSC 7000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。PSC 7000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
PSC 7000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPSC 7000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、PSC 7000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPSC 7000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
