QSC AudioメーカーPB2082-Iの使用説明書/サービス説明書
ページ先へ移動 of 20
TD-000218-00 revB ILA Series Loudspeaker Sy stem User Manual WL2082-i full-range line array lou dspeaker WL115-sw subwoofer line array loudsp eaker FB2082-i array frame EB2082-i extensi on bar PB2082-i pull back bar GS115-sw ground stack kit *TD-000218-00* 1675 MacArthur Blv d.
2 IMPORT ANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer .
3 Introduction The Installation Line Array (ILA) is a high performance line array system designed for the needs of Houses of W orship, Performi ng Arts facilities and a multitude of other venue ty pes.
4 Introduction (continued) WL115-sw The WL115-sw subwoofer extends the system’ s low-frequency capability to 35 Hz. with a compact fourth-order bandpass enclosure. Its ceramic magnet, 4” voice coil, 15” transducer provides 650 watt continuous power handling capability .
5 Figure 3: FB2082-i Array Frame 1- Shackle holes (accept 3/4” (20 mm) screw pin anchor sh ackle) 2- Center support bar 3- Rigging plates 4- Rigging plate retai ning bolts 5-Rigging plate attac hmen.
6 Rigging the Installation Line Array Rules for Suspension •Correct use of all suspension hardware and components is imperative in sound system rigging and deployment. •Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits.
7 Rigging the Installatio n Line Array (continued) 1- Working L oad Limits are per f astener loaded in doub le shear . Data is for informatio nal purposes only . Attaching WL2082-i to Array Frame Before beginning any installation, have your syst em designer configure the array with proper splay angles using QSC’ s EASE Focus (Array Calcul ator).
8 Rigging the Installation Line Array (continued) Pull-Back Bar If using the pull-back bar , attach to the bottom enclosure at the bot- tom-most splay angle adjustment holes at the rear of the rigging plate by inserting the cap-head shoulder bolt through the mated piec es and threading the lock nut (nylock) on the inside edge of the plates.
9 Rigging the Installation Line Array (continued) 3- Lower the array frame onto the enclosure, carefully aligning the rigging straps, and attach the top enclosure to the array frame by installing the ball-lock pins or M8 bolts. Before lifting, ensure the audio connection to the enclosures are correct and functioning.
10 Rigging the Installation Line Array (continued) Attaching WL115-sw behind WL2082-i array using EB2082-i It is sometimes necessary to suspend the subwoofers behind the main array . Extrem e splay angles may result in physical interference with rear -flown subwoofers .
11 WL2082-i Controls and Connections MODE Selection Switch BI AMP: When set to BI AMP , an internal shading net- work removes the mid-frequencies from one of the low- frequency drivers. The BI AMP HORIZONT AL SHADING switch will select which transducer is shaded.
12 WL115-sw Connections Input Connections The WL115-sw input connectors are a pair of Neutrik NL8's wired in parallel. See T able 3 or the WL115-sw Input Plate for connector pinout. Note pin numbers 2+, 2-, 3+, 3-, 4+, and 4- are wired straight throug h from one connector to the other .
13 WL2082-i Specifications Frequency Response: 80 - 20,000 Hz (+/- 3 dB) Frequency Range: 68 - 22,000 Hz (-10 dB) Maximum SPL (continuous/peak): HF: 126/132 dB LF: 122/128 dB Nominal Coverage (-6 dB included): Horizontal: 140 degrees (500 Hz to 3.
14 WL115-sw Specifications Frequency Response: 37 - 107 Hz (+/- 3 dB) Frequency Range: 35 - 112 Hz (-10 dB) Maximum SPL (continuous/peak): 124 dB/130 dB T ransducer: 650W , 8 Ohm 15 inch woofer , 4 inch voice coil, ceramic magnet assembly Recommended Crossover Frequency: 35 - 85 Hz Input Sensitivity: 96 dB Weight: Net: 111 lb (50.
15 EB2082-i Specifications Material: Aluminum 6061-T6 Finish: Black powder coat (White optional) Working Load Limit Informatio n: FB2082-i Specifications Material: Aluminum 6061-T6 Finish: Black powde.
16 PB2082-i Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Working Load Limit Information: GS115-sw Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Weight 5 lb (2.
17.
18.
19.
QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2006 “QSC” and the QSC logo are registered with the U.S. Patent and T rademar k Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc.
デバイスQSC Audio PB2082-Iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
QSC Audio PB2082-Iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはQSC Audio PB2082-Iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。QSC Audio PB2082-Iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。QSC Audio PB2082-Iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
QSC Audio PB2082-Iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はQSC Audio PB2082-Iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、QSC Audio PB2082-Iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちQSC Audio PB2082-Iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
