QSC AudioメーカーPLX 3102の使用説明書/サービス説明書
ページ先へ移動 of 16
PLX Series Professional Audio Amplifiers User Manual 4-ohm minimum imped ance models with Sp eakon ® output termina ls: PLX 1104 PLX 1804 2-ohm minimum imped ance models with Sp eakon and bindin g po st terminals: PLX 1802 PLX 2502 PLX 3102 PLX 3602 *TD-000214-00* TD-000214-001Rev .
2 Important Safety Precautions & Explanation of Symbols 1- Read these instructions. 2- Keep these instructions. 3- Heed all warn ings. 4- Follow all instr ucti ons. 5- WARNING: T o prevent fire or electric shock, do not expose this equ ipment to rain or moistu re.
3 Introduction Thank you for purchasing this QSC power amplifier . Please read t he following directions to obtain the best results. This manual covers all models of the PLX series.
4 Rack Mounting Use four screws and washers to mount the amplifier to the equipment rack rails. T o use the amplifier outside a rack, attach the self-adhesive rubber feet to the bottom. For portable, mobile, or other applications where the rack assembly may be moved, we strongly recommend support- ing the rear of the amplifier .
5 Cooling Air flows from the rack, into the back of the amplifier , and out the front. This keeps the rack cool. The fan automatically runs faster when the amp is working hard. Do not block the front or rear air vent s! AC Mains Connection Connect AC power to the IEC socket on the back of the amplifier .
6 Input Configuration Switch (PLX 1802/2502/3102/3602 models only) Select the input configuration by sliding the switch to the position which corresponds with the desired input configuration.
7 Inputs Each channel has a balanced XLR (female) and 1/4-inch TRS input. The XLR and TRS connectors for each channel are wired in parallel and can be used for “ daisy chain- ing” an input signal to additional amplifiers. The input impedance is 20k ohm balanced or 10k ohm unbalanced.
8 Outputs The PLX 1104 and PLX 1804 models are equipped with Speakon output connectors for each channel. PLX 1802, PLX 2502, PLX 3102, and PLX 3602 models are equipped with Speakon and binding post output connectors. Wiring connections are shown on the back of the chassis.
9 LED Indicators The LED indicators can be used to monitor system operation and identify common problems. POWER (PWR): BLUE Normal indication: •AC switch ON: LED will illuminate. If no indication: •Check AC power cord and AC outlet. •Confirm that AC switch is in ON position.
10 Gain Controls T urn the GAIN controls clockwise to increase gain and counter clockwise to decre ase gain. The GAIN controls are marked in dB of attenuation. There are 21 detents for repeatable adjustments. The upper 14 steps are about 1 dB each, and settings should normally be made within this range.
11 Protection Sy stems Both amplifier platforms are fully protected against adverse conditions, but their behavior and user adjustments are different. PLX 1802/2502/3102/3602 models: •Clip Limiting may be switched on the rear panel to prevent seve re overdrive.
12 Specifications PL X 1104, PLX 1804 PLX 1104 PLX 1804 OUTPUT POWER (Watts) (1) 20 - 20k Hz, 0.05% THD, 8 ohms/Ch. 310 550 1k Hz, 0.1% THD (EIA), 8 ohms/Ch. 325 600 20 - 20k Hz, 0.05% THD, 4 ohms/Ch. 500 800 1k Hz, 0.1% THD (EIA), 4 ohms/Ch. 550 900 DISTORTION, SMPTE-IM 0.
13 Specifications PLX 1802, PL X 2502, PLX 3102, PLX 3602 PLX 1802 PLX 2502 PLX 3102 PLX 3602 OUTPUT POWER (W atts) (1 ) 20 - 20k Hz, 0.05% THD, 8 ohms/Ch. 320 425 550 725 1k Hz, 0.1% THD (EIA), 8 ohms/Ch. 330 450 600 775 20 - 20k Hz, 0.05% THD, 4 ohms/Ch.
14 Appendix A: Speakon Wiring Reference Amplifier co nnection T o loudspeaker T wo-wire, si ngle-channel conn ection Four -wire, two-channel connect ion Bridge mode connect ion NOTE! Ensure proper pol.
.
QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2006 “QSC” and the QSC logo are registered wi th the U.S. Patent and T rademark Office.
デバイスQSC Audio PLX 3102の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
QSC Audio PLX 3102をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはQSC Audio PLX 3102の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。QSC Audio PLX 3102の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。QSC Audio PLX 3102で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
QSC Audio PLX 3102を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はQSC Audio PLX 3102の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、QSC Audio PLX 3102に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちQSC Audio PLX 3102デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。