QSC AudioメーカーSC28の使用説明書/サービス説明書
ページ先へ移動 of 16
SC281675 MacArthur Blvd., Cost a Mesa, CA, 92626 USA Main Number (714) 75 4-6175 or toll free (USA only) (800) 854-407 9 Customer Service(714) 957-71 50 or toll free (USA only) (800) 772-2834 Loudspeaker Signal Processing Products User Manual SC28 T wo-Input, Eight-Output Sy stem Controller for QSC Loudspeakers *TD-000238-00* TD-000238-00 rev.
2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol wit hin an equilateral tri angle is intended to al ert the user to the presence of uninsula ted “dangerous” voltage within the product’ s enclosure that may be of sufficient magnitude to constit ute a risk of electri c shock to humans.
3 Introduction Congratulations and thank you for your purc hase of this professional, loudspeaker signal processing product. T o get the most fr om your investment, we recommend you review all the information provided in this Use r Manual.
4 Unpacking There are no special unpacking precautions. However , it is recommended you keep the original packing material for reuse in the rare event that service be required.
5 Audio Inputs On the rear panel, there are two female XLR line-level inputs marked INPUTS below the connectors and designated A and B above the connectors . Connect the line-level analog audio inputs to these connectors. Input sensitivity can be selected from the Setup Menu ; selections are 1.
6 Use General Information Use of the SC28 involves adherence to the following to achieve proper operation: 1- Input sensitivity for the SC28 must be set to correspond with expected audio source levels .
7 LED Indicators LED metering of both input and output are provided. Input metering is indicated as relative to 0 dBfs (digital clipping of the input signal) and output metering is indi- cated in actual output voltage levels in dBu. Meters are peak-reading and updated every 50 milliseconds.
8 LCD Navigation Map- Setup PL 3 : 32 dB gain PL 3 : 32 dB gain PL 3 : 32 dB gain WL/GP-218 sw WL/GP-212 sw WL-1 15 sw WL 10 3way REV WL 10 3way WL 10 2way WL 8 3way < LF > WL 8 3way > LF <.
9 LCD Navigation Map- Equalization.
10 LCD Navigation Map- Gain.
11 LCD Navigation Map- Utility.
12 Signal Flow.
13 Dimensions.
14 Preliminary Specification Dynamic Range (AES-17, -60 d B Method, all sensitiviti es) unweighted >104 dB A weighted >107 dB Distortion (AES-17, 20 Hz- 20 kHz, all sensitivities) +4 dBu <0.
15 Preliminary Specification USB Port USB type “B” USB Cable 1.5 meters long, USB 1.1 compliant AC Power Requirements 100-240 V AC, 50-60 Hz, no user adjustment required AC Power Connection IEC-type inlet AC Power Cord 2 meters long, #18A WG Specifications are subj ect to change w ithout notice.
W arranty (USA only; other countries, see your dealer or dist ributor) Disclaimer QSC Audio Products, LLC is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and/or use of this loudspeaker product.
デバイスQSC Audio SC28の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
QSC Audio SC28をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはQSC Audio SC28の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。QSC Audio SC28の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。QSC Audio SC28で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
QSC Audio SC28を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はQSC Audio SC28の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、QSC Audio SC28に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちQSC Audio SC28デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。