RangemasterメーカーVESCM52BLの使用説明書/サービス説明書
ページ先へ移動 of 24
VESPER Instructions Manual www.rangemaster.co.uk.
2 2 INDEX RECOMMENDATIONS A ND SUGGEST IONS ..................................................................................................................... 3 CHARACTER ISTICS ......................................................................
EN 3 3 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Us e apply to several versions of this appliance. Accordingly, y ou may find descriptions of indivi dual features that do not apply to you r specific appliance. INSTALLATION • The manufa cturer will not be held liable f or any damages resulting from incorre ct or improper installation.
EN 4 4 CHARACTERISTICS Components Ref. Q.ty Product Components 1 1 Hood Canopy complete with: Controls, Light, Filters, Motor. 2 1 Hood support Plate (with lamp holder) 3 1 Power supply cable lock 4 1 Cable raceway 5 1 Glass or Panels the other material 14 1 Pawl Ref.
EN 5 5.
EN 6 6 Dimensions.
EN 7 7 INSTALLATION This hood is designed to be mou nted on the ceil ing/on a shelf, above a free-standing H ob (min. 650 mm), in: • Ducting version : Evacuation to the outside.
EN 8 8 Ceiling/Shelf drilling and Plate Fixing CEILING/SHELF DRILLING • Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling /Shelf.
EN 9 9 FIXING THE PLATE • Lift up the fixing plate, t aking care to ensure that the l imit pawl is positioned frontally. • Fit the slots onto the two screws previously inserted in the ceiling, and turn until the y are at the centre of the adjustment slot.
EN 1 10 CONNECTING HOOD-PLATE CABLES N.B. Before continuing with installation it is necessary to move the hoo d to a height of at least 650 mm from the cooker hob, using a support or the assistance of an- other pers on.
EN 1 11 • Attention to the direction of the plate fixed to the ceiling (th e limit pawl on the plate fastened to the ce iling has a corresponding hole on the plate cover and on the hood canopy). • Insert the cables into the safety knobs ( c ) with the thread a t the top.
EN 1 12 • Pass the cables through the slots in the thr eaded pawls ( a ) and screw the cable locking scre ws ( b ) to the pawls them- selves. • When the operation has been completed the result must be as shown in the figure for all 4 ca- bles.
EN 1 13 • At this point it is possible to connect up the hood, and the lamp if there is one, to the power supply using the resp ective power cables. • Close the plate cover using the 3 screws removed previously and the wrench provided • At this point the Hood is sus- pended.
EN 1 14 Connections AIR OUTLET - DUCTING VERSION To install the hood in the ducting version , please refer to the instructions provided in th e ducting kit specific to the hood. AIR OUTLET – RECIRCULATION VERSION • Open the lighting unit by pulling on the notch prov ided.
EN 1 15 LEVELLING THE HOOD • The hood mobile unit must be levelled to allow the movement to operate properly. • The hood is levelled by adjusting the safety pawls. • Rest a spirit level on the hood. • When the safety knobs are pressed upwards, movement of the hood is “unlocked”.
EN 1 16 FIXING THE POWER SUPPLY CABLE • Wind the power cable around its axis so that it forms a spiral from the mobile b ody to the plate in the ceiling. • It is importan t to do this to prevent th e wire come out from the hood body during the closing of th e hood • Take the cable clamp 3 provided.
EN 1 17 FITTING THE GLASS (OR OTHER MATERIAL) • Take the lamps and insert th em in the lamp holder s. • They do not have to be screwed in, but simply inserted al l the way. • Fix the glass (or other material) 5 to the plate using the fixing knobs 12d .
EN 1 18 USE Control panel L T1 Button Function Display L Turns the lights On/Off. - T1 Hood Down Press for 2 seconds to raise the Hood. Press briefly to turn the Motor On/Off. On/Off Hood Up Press once: The Hood lowers. Press a second time: The Hood Stops.
EN 1 19 REMOTE CONTROL The appliance can be controll ed using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included). • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner.
EN 2 20 MAINTENANCE Grease filter The filter mus t be cleaned ever y 2 months of op era- tion, or more frequently for particularly heavy usage, and can be washed in a dishwasher. CLEANING METAL SELF- SUPPORTING GREASE FIL- TER • Open the lighting unit by pulling on the nocth.
EN 2 21 Lighting LIGHT REPLACEMENT 20 W halogen light. • Remove the snap-on lamp cove r by levering it from under the metal ring, supporting it with one hand .
EN 2 22 Additional information for the installation tec hnician • Open the lighting unit by pulling on the notch prov ided. • Apply the label, indicated the type of li ghting, on the Hood as indicated in the figure (Rif.
.
991.0302.95 0_ver1 AGA RANGEMASTER GROUP PLC.
デバイスRangemaster VESCM52BLの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rangemaster VESCM52BLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRangemaster VESCM52BLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rangemaster VESCM52BLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rangemaster VESCM52BLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rangemaster VESCM52BLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRangemaster VESCM52BLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rangemaster VESCM52BLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRangemaster VESCM52BLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。