RaypakメーカーRHP 33の使用説明書/サービス説明書
ページ先へ移動 of 19
Raypak ® RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL This manual should be maintained in legible condition and kept adjacent to the heat pump or in a safe place for future use. For additional information call: (03) 9757 3333 Effective Date: Dec 2004 Replaces: All Previous V ersions Part No.
PRODUCT SAFETY SIGNS AND LABELS This manual, as well as the pool/spa heat pump itself, contains product safety signs and labels. Please read these signs and labe ls, as they convey important safety information about hazards that may be potentially present in and around the heat pump.
RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I. Installation . . . . . . . .
Intr oduction This pool/sp a heat pump is an electro mechanical machine that incorporates a pressurised refrigerant gas in a sealed system. ONL Y trained and qualified service personnel should attempt to inst all or service this equipment.
• Each side of the unit must be located at least 300mm from walls, pipes, or other obstructions for unrestricted air intake and service access. Do not inst all the unit within 1m of fossil fuel burning heaters.
III. W ater Connections The heat pump inlet and outlet connections are NOT interchangeable. They must be connected as instructed below . 1. Connect the heat pump in the return water line between the pool filter and the pool. See page 10, Plumbing Diagrams.
Indicator Lamps : There are 6 indicator lamps located on the unit control panel: • Power (amber lamp): When lit, indicates power is applied to the unit. • Wa t e r Flow (green lamp): When lit, indicates normal water flow . • Heat Demand (green lamp): When lit, indicates the actual water temperature is below the target water temperature.
NOTE: The heat pump will be OFF when the Remote position is selected on the Po ol/Sp a selector switch. 4.Allow the heat pump to operate for a few minutes to stabilize operating pressures and to allow various component temperatures to normalize.
VIII. Summer Shutdown If you do not plan to use the pool heat pump during the summer months, secure and protect it as follows: 1. From the control panel, turn the control switch to Remote (OFF). 2. T urn the heat pump power switch to OFF. 3. Leave the valves set the way they are unless additional circulation is required.
2. B. Cabinet Care (optional) - The cabinet is designed for outdoor use and requires little care. However , you can clean it if you wish. 1. 2. W ash the cabinet with soap and water .
operation. After the desired temperature is reached, return the system to normal operation. •I s airflow through the unit being obstructed? Restrictions such as shrubbery , tall grass, dirty coils, or any other obstruction to airflow will reduce performance.
POWER SUPPL Y •V erify that all circuit breakers are reset and working properly . •I f t h e Power lamp on the control panel still does not light, contact the installing dealer , since it may be a power problem requiring an electrician. WAT E R F L O W •V erify that the filter is clean to provide good flow .
Plumbing Diagrams For systems with pumps of le ss than 2 HP(1.5Kw) (und er 300 l/min), no external bypass is required. Connections a re 50 mm pipe slip. Plumb the heat pump after the filter and before any chlorinators. Wa t e r I n (from pool or S pa) Wa t e r O u t (to pool or S pa) Filter For systems with pumps of 2 HP (1.
Heat Pump Schematic 12 4 3 A B C D 4 3 2 1 D C B A e l t i T n o i s i v e R r e b m u N e z i S A f o t e e h S 3 0 0 2 - n a J - 7 2 : e t a D : y B n w a r D b d d .
Contr ol Panel Assembly Replacement Parts List 12 4 7 13 11 10 16 11 9 15 2 5 8 14 3 6 1 ITEM QTY DESCRIPTION PART No. 11 Control Panel 21 Contactor Compressor 31 F a n Relay 41 Control Board 24Volt 5.
Contr ol Panel Cover Assembly Replacement Parts List 1 4 4 4 7 6 7 6 8 8 5 Front ITEM QTY DESCRIPTION PART No. 11 Control Panel Cover 22 P O T 31 S w i t ch Type A403 43 K n o b 51 Label Control Panel.
Heat Pump Assembly Replacement Parts List - RHP 3 3 11 15 13 12 5 9 2 9 16 7 7 18 14 6 7 3 17 19 4 10 1 8 Model RHP 33 *See assembly drawing in this manual IT EM QTY DESCRIPTION PART No.
15.
16.
デバイスRaypak RHP 33の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Raypak RHP 33をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRaypak RHP 33の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Raypak RHP 33の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Raypak RHP 33で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Raypak RHP 33を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRaypak RHP 33の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Raypak RHP 33に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRaypak RHP 33デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。