RazorメーカーE100の使用説明書/サービス説明書
ページ先へ移動 of 24
Ow n er ’ s M an u a l Item Numbers E100 13100E-BL E125 13125E-BK Black 13111110 Red E150 13111612 E200 13200E-SL E200S 13201S-SL E225S 13112850 E300 13300E-SL E300S 13301S-SL E325S 13116390 Read and underst and this entire manual before riding! DO NOT RETURN TO STORE! NOTE: E100/125/150 must be traveling 3mph before motor will engage.
WARNING: Riding the E100, E200 or E300 scooter can be a hazardous activity . Certain conditions may cause the equipment to fail without fault of the manufacturer .
Charger Charger Plug Charger Port Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
3 ASSEMBL Y AND SET -UP q Attaching the Handl ebars W ARNING: Failure to properly tighten the wedge may allow the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly tightened, the handlebars will not rotate out of alignment with the front wheel under normal circumstances.
q Adjusting the Handl ebar Height (E100/E200/E300 only) q Riding Y our Scooter T esting the Brakes – T o use the brakes, squeeze the front and back brake levers to increase the pressure on the brake. The brake lever is fitted with a cable adjuster to compensate for cable stretch and/or to fine-tune the lever movement to brake engagement.
5 REP AIR AND MA INTENANCE 1 Use the special valve extender/adapter supplied. The valve adapter is located in the bag with the owners manual supplied at the time of purchase. 2 Align the access hole in the drive sprocket with the tire valve. Thread the adapter completely onto the valve and attach the pump.
6 REP AIR AND MA INTENANCE q Adjusting the Chain Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 Using two 17mm wrenches, loosen the rear axle bolts by turning the wrenches counter clockwise. 2 Using two 8mm wrenches, loosen the brake housing anchor which is located in the long slot on the left side of the rear fork.
7 REP AIR AND MA INTENANCE q Chain and Rear T ire Replacement Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 With a Phillips screwdriver , loosen the two screws and remove the chain guard. 2 With a 10mm wrench, loosen the brake cable anchor and disconnect the cable.
8 REP AIR AND MA INTENANCE 10 Install the axle adjusters and axle nuts. T ighten until they just barely hold the hardware in place. 11 T ighten both axle adjust- ers the same number of turns to fine-tune the tension on the chain and to approximately maintain the centering of the wheel.
9 REP AIR AND MA INTENANCE 1 (E100 only , other models go to Step 2) Loosen the brake pad bolt and remove one brake pad. q Front T ire Replacement Tools required: 10mm wrench, two (2) 17mm wrenches and a flathead screwdriver . 2 Using two 17mm wrenches, loosen the front axle bolts by turning the wrenches counter clockwise.
10 q Battery Care and Di sposal Do not store the battery in temperatures above 75° or below -10° F . CONT AINS SEALED LEAD BA TTERY . BA TTERY MUST BE RECYCLED. Disposal: Y our Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally sound manner .
11 TROUBLES HOOTING GUIDE Scooter does not run Scooter was running but suddenly stopped Short run time (less than 30 minutes per charge) Scooter runs sluggishly Problem Possible Cause Solution Undercharged battery Charger is not working Loose wires or connectors E100 only - Scooter must be traveling 3mph before motor will engage.
12 Need Help? V isit our web site for updates and a list of authorized service centers at ww w .razor .com or call toll -free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific T ime. TROUBLES HOOTING GUIDE Need Help? V isit our web site for updates and a list of authorized service centers at ww w .
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.
E100 P ARTS 14.
E150 P ARTS Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability .
E150 P ARTS 16.
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.
E200 P ARTS 18 Only used on E200S.
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.
E300 P ARTS 20 Only used on E300S.
SB 1918 (CALIFORNIA) DECLARA TION YOUR INSURANCE POLICIES MA Y NOT PROVIDE COVERAGE FOR ACCIDENTS INVOL VING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONT ACT YOUR INSURANCE COMP ANY OR AGENT .
.
T ire Inflation Periodically inspect the t ires for excess wear , and regularly check the ti re pressure and re- inflate as necessary . If you get a flat tire, the inner tube can be patched or a new tube can be purchased from Razor or an authorized repair center .
デバイスRazor E100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Razor E100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRazor E100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Razor E100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Razor E100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Razor E100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRazor E100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Razor E100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRazor E100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。