RazorメーカーE200の使用説明書/サービス説明書
ページ先へ移動 of 13
Owner’s Manu al Item Number: E200 13112430 E200S 13112730 E225 13112801 Read and understand this entire manual before riding! DO NOT RETURN TO STORE! NOTE: Manual illustrations are for demonstration purposes only . Illustrations may not reflect exact appearance of actual product.
Safety Warnings ............................................................... 1 Before Y ou Begin .............................................................. 2 Assembly and Set-Up .................................................... 3-4 Hardware Maintenance .
BEFORE YOU BEGIN 2 WARNING: DO NOT USE NON- RAZOR PRODUCTS WITH YOUR RAZOR ELECTRIC SCOOTER. The scooter has been built to certain Razor design specifications. The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame, fork and all other parts.
3 ASSEMBL Y AND SET -UP 1 Use the valve extender/ adapter located in the end of the right handlebar grip. 2 Open the round cover located on the chain cover by sliding the cover upward. Align the opening in the drive sprocket with the valve stem. Thread the adapter completely onto the valve stem and attach the pump.
4 ASSEMBL Y AND SET -UP Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at www .razor .com or call toll-free at 866-467-2967 Monday - Friday 8:00AM - 5:00PM Pacific T ime.
5 REP AIR AND MAINTENANCE CONNECTORS/HARDW ARE MAINTENANCE Safety Gear Always wear proper protective gear such as an approved safety helmet. Elbow pads and kneepads are recommended.
6 q Chain and Rear T ire Replacement Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 With a Phillips screwdriver , loosen the two screws and remove the chain guard. 2 With a 10mm wrench, loosen the brake cable anchor and disconnect the cable.
7 REP AIR AND MAINTENANCE q Front T ire Replacement Tools required: two (2) 17mm wrenches and a flathead screwdriver . 1 Using two 17mm wrenches, loosen the front axle bolts by turning the wrenches counter clockwise. 2 Remove wheel and install re- placement wheel.
q Adjusting the Chain Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 Using two 17mm wrenches, loosen the rear axle bolts by turning the wrenches counter clockwise. 2 Using two 8mm wrenches, loosen the brake housing an- chor bolts which is located in the long slot on the left side of the rear fork.
9 TROUBLESHOOTING GUIDE Scooter does not run Scooter suddenly stopped working while in use Short run time (less than 15 minutes per charge) Scooter runs sluggishly Sometimes the scooter doesn’t run,.
10 Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability . (Specifications subject to change without notice.
SB 1918 (CALIFORNIA) DECLARA TION YOUR INSURANCE POLICIES MA Y NOT PROVIDE COVERAGE FOR ACCIDENTS INVOL VING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONT ACT YOUR INSURANCE COMP ANY OR AGENT .
01/2010 Community Design No. 130919-0001 U.S. Design Patent D497,397 S U.S. Desing Patent D513,629 S Canadian Design Registration No. 105673 Printed in China for: Razor USA LLC PO Box 3610 Cerritos, CA 90703 Copyright © 2003-2010 Razor USA LLC. All rights reserved.
デバイスRazor E200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Razor E200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRazor E200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Razor E200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Razor E200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Razor E200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRazor E200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Razor E200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRazor E200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。