Audiovoxメーカー128-7853の使用説明書/サービス説明書
ページ先へ移動 of 16
128-7853 1 of 16 1 Model APS-920 Inst allation Manual This Remote St art/Alarm System is designed to be used with Automatic T ransmission- Fuel Injection V ehicles Only! COMPONENTS: Control Module 1 Four Button RF T ransmitter 1 Four Button LCD T ransmitter 2 Way Antenna/Receiver 1 “1 X 1.
128-7853 2 of 16 2 INST ALLA TION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow con- nection of the 6 pin main wiring harness.
128-7853 3 of 16 3 SIREN: Select a location in the engine compartment that is not accessible from below the vehicle. The selected location must be clear of hot or moving parts within the engine compar.
128-7853 4 of 16 4 DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCON- NECT THE NEGA TIVE BA TTERY CABLE FROM THE VEHICLE BA TTERY PRIOR T O MAKING ANY CONNECTIONS.
128-7853 5 of 16 5 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the "ON" o.
128-7853 6 of 16 6 false triggering of the factory alarm when the remote start unit engages or when the transmitter is used to unlock the doors. NOTE: This output can be selected to operate like the door lock output as set in alarm feature setting #1 by selecting feature #13 of Bank 3 to as door unlock pulse.
128-7853 7 of 16 7 Orange: Ground While Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay .
128-7853 8 of 16 8 Brown Wire: Negative Door Trigger If the vehicle's door courtesy light switches ground when the door is opened, (Most GMs and Imports), you must connect this wire to the negative output from one of the vehicle's door pin switches.
128-7853 9 of 16 9 Green/Y ellow Wire: DIESEL W AIT T O ST ART INPUT The green/yellow wire, when connected to the wire that get + 12 volts during the glow plug preheat stage will delay the starter output until this wire drops the 12 volts.
128-7853 10 of 16 10 The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: B. Additional Ignition Output: C.
128-7853 11 of 16 11 4 Pin Shock Sensor Connector “D” Red, Black Green & Blue wires of the shock sensor harness provide +12 V olts, Ground, Full T rigger , and Pre-Detect inputs to and from the sensor . Route these wires from the previously installed sensor and connect to the mating connector on the control module.
128-7853 12 of 16 12.
128-7853 13 of 16 13 Setting Up The System Programming Features: Bank 1 Transmitter Channels S tart with the system disarmed, tun the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully entered.
128-7853 14 of 16 14 Programming T ach Rate: NOTE: All applications require that tach be programmed. The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored.
128-7853 15 of 16 15 3. Within 10 seconds of the key turning off, cycle the enable switch Off, On, Off, On ( 2 times) to select a 2 hour timed start interval. Cycle the enable switch Off, On, Off, On, Off, On, Off, On (4 times) to select a 4 hour timed start interval.
128-7853 16 of 16 16 © 2006 Audiovox Electronics Corporation 150 Marcus Blvd. Hauppauge N.Y . 1 1788 128-7853.
デバイスAudiovox 128-7853の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox 128-7853をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox 128-7853の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox 128-7853の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox 128-7853で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox 128-7853を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox 128-7853の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox 128-7853に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox 128-7853デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。