RenesasメーカーEDK3687の使用説明書/サービス説明書
ページ先へ移動 of 16
EDK3687 U SER M ANUAL F OR H8/3687 O N - CHIP FLASH M ICROCONTROLLER.
Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduc e or duplicate, in any form, a part or this entire document without Renesas Technology Europe Limited's written permission.
1. T ABLE OF C ONTENTS 1. T ABLE OF C ONTENTS ............................................................................................................................................. 3 2. S TART - UP I NSTRUCTIONS ................................
2. S T ART - UP I NSTRUCTIONS 2.1. I NSTALLING THE E VALUATION D EVELOPMENT K IT (EDK) Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this EDK at: http://www.
3. EDK B OARD L AY O U T The diagram shows a general layout of the EDK board. 9-W ay D-Type Power RESET Switch NMI Switch User1 LED User2 LED Power LED FLASH Programm ing CJ4 5V UVcc GND RESn FW NMIn ULED1 ULED2 PSCK PTXD PRXD RX232 TX232 CTS RTS Microprocessor LIN I2C J1 J2 XTAL OSC Testpoints SPI DEBUG LIN I2C F IGURE 3-1: EDK B OARD L AYOUT 3.
4. EDK O PERA TION 4.1. USER INTERFACE The EDK provides two buttons for influencing the operation of the board. The purpose of each b utton is clearly marked next to it.
4.2.2. C RYSTAL C HOICE The operating crystal frequency has been chosen to support the fa stest operation with the fastest serial operating speeds. The value of the crystal is 18.432MHz. The following table shows the baud rates and Baud Rate Register (BRR) setting required for each communication rate using the above default operating speed.
4.4. I2C EEPROM The board has been tested with an Atmel AT24C04AN- 10SI-2.7 I2C EEPROM device (Not supplied). The device is configured to connect to dedicated I2C pins on Ports P56 and P57. 4.5. LIN I NTERFACE The board has been tested with an Philips TJA1020TD device (Not supplied).
5. B OARD O PTIONS The EDK has a number of configuration settings set by four jumpers CJ4 (A, B, C, D) and zero-ohm links. Common EDK functions can be set using the jumpers as de scribed in sect ions 5.2. The additional zero-ohm links provid e additional features that may be required to interface with other systems.
5.2. EDK O PTIONS – CJ4 The EDK options provide access to co mmonly used features of the EDK range. These jumpers must be fitted at all times to ensure correct operation of the EDK.
5.3. O PTION L INK S ELECTION The following sections show the option links that apply to each pe ripheral device. The tables all use the same key of symbols which is given below: X – Groups of options one set of which must be fitted for correct operation of the EDK.
5.3.3. SPI – S ERIAL P ERIPHERAL I NTERFACE The SPI interface is not directly compatible with the SCI in terface on the device. Selection of the connections to the SPI interface should therefore be chosen to allow t he operation of other peripherals as required.
6. M ICROCONTROLLER H E ADER C ONNECTIONS The following table lists the connections to each or the headers on the board. 6.1. H EADER J1 J1 Pin No Function EDK Sy mbol Device pin Pin No Function EDK S.
7. C ODE D EVELOPMENT 7.1. HMON 7.1.1. M ODE S UPPORT The HMON library is built to support Normal Mode only. 7.1.2. B REAKPOINT S UPPORT The monitor utilises the Address Break Controller for code located in ROM, allowing a single breakpoint to be set in the code.
7.1.4. M EMORY M AP On-Chip FLASH ROM On-Chip RAM Interna l I/O REGISTERS On-Chip RAM Vectors FDTInit FDTUserM odeM icr oKerne l PHMO N CHMO N CUser_Vectors BHMO N Stack H'0400 H'04F7 H&apos.
7.1.5. B AUD R ATE S ETTING HMON has initially set to connect at 115200Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please refer to the HMON User Manual for further information.
デバイスRenesas EDK3687の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Renesas EDK3687をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRenesas EDK3687の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Renesas EDK3687の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Renesas EDK3687で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Renesas EDK3687を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRenesas EDK3687の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Renesas EDK3687に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRenesas EDK3687デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。