RenesasメーカーH8/36902の使用説明書/サービス説明書
ページ先へ移動 of 35
Revision Date: Jun. 22, 2005 Renesas Micro computer Devel opment Environme nt System H8 Fam ily / H 8/300 H Tiny Series HS36902ECH61HE Rev.1.00 H8/36912, H8/36902 Gro up FP-32A User System Interface C.
.
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp.
.
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user sys tem interface cable until you fully understand its mechanism.
II LIMITED WARRANTY Renesas warrants its user system interfa ce cabl es to be manufactured in accordance with published specifications and fr ee from defects in material and/or workmanship. Renesas will repair or replace any user system interfac e cables determined to be defective in material and/or workmanship.
III State Law : Some states do not allo w the exclusion or limitation o f implied warranties or liab ility for incidental or c onsequentia l damages, so the above li mitation or exclusion may not appl y to you. This warrant y gives you s pecifi c legal rights , and yo u may have ot her rights which ma y vary fr om state to state.
IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user sys tem interface cable until you fully understand its mechanism.
V W ARNING Observe the pr ecautions listed b elow. Failure to do so will result in a FIRE H AZARD and will damage the user system and the emul ator product or will result in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock prevention and qualit y assurance.
VI.
i Preface Thank you for purchasing this user s y stem interface cable (HS36902ECH61H) for the Renesas ’ original microcomput er H8/36912, H8/36902 group.
ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interface C able to Emulator Station .
1 Section 1 Configuration CAUTION Use an NQPACK 032SA socket (manufact ured by Tokyo Eletech Corporation) for the FP-32A package IC socket on the user system. Figure 1 shows the configuration of the HS 36902ECH61H user system interface cable for the FP-32A package.
2 Table 1 list s the HS36902EC H61H components. Pl ease make sure you have all of these components when unpacking. Table 1 HS36902ECH61H Com ponents No.
3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY.
4 E6000 Emulator station User system interface cable CTS screws (M3 x 6 mm) Cable body connector Figure 2 Connecting User System Interface Cable to E mulator Station.
5 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned.
6 2.2.1 Installing IC So cket After checking the location of pin 1 on the IC socket fasten it to the us er system before soldering. CAUTION After confirming the locat ion of pin 1 on the IC socket, apply epoxy resin adhesive to the end of t he four projections at the bott om of the IC socket, and fasten it to the user system.
7 CAUTION Be sure to completely solder th e leads so that th e solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.
8 Fasten the user sys tem interface cable head to the IC socket for an FP-32A package on the user system with the two screws (M2 x 10 mm) provided. Each screw should be tightened a little at a time, alternati ng between screws on opposing corners.
9 2.2.4 Fastening C able Body Connect the cable body t o the cable head. Cable head Remove jig User system Push the unfastening jigs. Removing Cable body Figure 5 Fastening Cable Body.
10 2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footpri n t) for the user system with an IC s ocket for an FP-32A package (NQP ACK032SA: manufactured by Tokyo Eletech Corporation).
11 2.4 Dimensions for User System Interface Cable Head The dimensions for the user s ystem interface cable head are shown in figure 7. Unit: mm Tolerance: ± 0.
12 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user s y stem interface cable head to the user system, are shown in figure 8. 19.7 29.2 IC socket (NQPACK032SA manufactured by Tokyo Eletech Corporation) Cable head User system Unit: mm Tolerance: ±0.
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for t ightening screws.
14 MCU Pin 1 IC socket (NQPACK032SA manufactured by Tokyo Eleteck Corporation) User system Screws (M2 x 6 mm) Socket cover Figure 9 Installing MCU to User System.
15 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator User’s Manual (HS3664EPI61HE-U2 or HS 3664EPI62HE-U2). 2. Verify the user system interface cable connections by access ing ports and checking the bus states of the pins.
16 Figure 10 sh ows the system clock o scillator on the user sy stem in terface cab le and the sub clock input specificat ions. R2 270 Ω R1 1 M Ω HCU04 HCU04 To E6000 emulator To E6000 emulator OSC1 OSC2 System clock oscillator Subclock oscillator R6 470 k Ω R5 3.
17 Section 5 Notice 1. Make sure that pin 1 on the user sys tem IC socket is correctly ali gned with pin 1 on the cable head before inserting the cable head into the user syst em IC socket. 2. The dimensions of the recommended mount pad for t he user system IC socket are different from those of the MCU .
18 6. The P1 short connector is us ed for testing. Do not remove the inse rted jumper pin. P1 1 3 Figure 12 P1 Short Connector.
19 7. SW1 and SW2 are us ed to switc h OSC2 or PC 1 and OSC1 or PC0. Turn SW1 and S W2 to the OSC1 and OSC2 sides , respectively, when they are used as OSC1 and OSC 2. Turn SW1 and SW2 to the PC 0 and PC1 sides, respecti v ely, when they are used as PC0 and PC 1.
20.
Renesas Microcomputer Development Environment System User's Manual H8/36912, H8/36902 Group FP-32A User System Interface Cable HS36902ECH61H Publication Date: Rev.1.00, June 22, 2005 Published by: Sales Strategic Planning Div. Renesas Technology Corp.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.
H8/36912, H8/369 02 Grou p FP-32A User System Interface Cable HS36902E CH61H User’s Manual.
デバイスRenesas H8/36902の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Renesas H8/36902をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRenesas H8/36902の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Renesas H8/36902の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Renesas H8/36902で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Renesas H8/36902を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRenesas H8/36902の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Renesas H8/36902に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRenesas H8/36902デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
