RIDGIDメーカーAC9940の使用説明書/サービス説明書
ページ先へ移動 of 16
1 This Miter Saw Utility V ehicle has been engineered and manufactured to our high standar d for dependability , ease of op- eration and operator safety . When properly car ed for , the Miter Saw Utility V ehicle will give you years of rugged, trouble-free performance.
2 n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation ......................................
3 RULES FOR SAFE OPERA TION Safe operation of this accessory requir es that you read and understand this operator's manual, the operator’ s manual for the miter saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n KNOW YOUR ACCESSOR Y .
4 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger .
5 UNP ACKING NOTE: Before beginning assembly , check that all parts are included. If you ar e missing any part, do not assemble this accessory . Call 1-800-4-RIDGID or E-mail us at info@rid gidwoodworking.
6 Fig. 3 ASSEMBL Y A TT ACHING THE LOWER FOOT See Figures 1 and 2. n Place stand assembly “flat” on floor . n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat W asher , M8 (4) Lock Nut, M8 (2) n Install bolt, two washers and lock nut as shown.
7 WORKST AND SET -UP See Figures 4 and 5. Before Y ou Start n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n If a compound miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable).
8 ASSEMBL Y MOUNTING MITER SA W See Figures 6 and 7. WARNING: Failure to unplug the tool could r esult in accidental starting causing possible serious personal injury .
9 ASSEMBL Y MOUNTING OTHER BRANDS See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will requir e additional 5/16 in. mounting holes to be drilled.
10 ASSEMBL Y EXTENSION BAR(S) OPERA TION See Figures 10 and 11. Both extension bars may be adjusted to pr ovide maximum workpiece support. T o adjust the extension bars: n Loosen adjustable handle by tur ning counter clockwise. NOTE: Adjustable handle can be repositioned if necessary .
11 FOLDING LEG AND T ABLE n Loosen the r oller foot knob and slide foot extension up. Tighten knob. n Release locking pin and raise foot. n Loosen the extension bar handle and slide extension bar in towards table. Tighten extension bar handle. n Repeat for the other side.
12 ASSEMBL Y TRANSPORTING TOOL See Figure 15. n When hauling the workstand in a vehicle, securely tie it down to prevent movement and possible damage. n Always get help if you need to lift the workstand. When lifting, hold the workstand close to your body .
13 EXPLODED VIEW/REP AIR P AR TS Miter Saw Utility V ehicle Model AC99400 RIDGID parts are at www .ridgidparts.com 1 829859 Rear Roller Extension 2 829758-5 W asher (20 x 10.5 x 1.5) 3 829759-3 Nylock Nut (M10) 4 829799 Rubber Cap 5 829757-6 Hex Head Bolt (M8 x 1.
14 NOTES.
15 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
16 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to pr ovide all relevant information when you call or visit. For the location of the authorized service center near est you, please call 1-866-539-1710 or visit us online at www .
デバイスRIDGID AC9940の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID AC9940をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID AC9940の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID AC9940の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID AC9940で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID AC9940を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID AC9940の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID AC9940に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID AC9940デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。