RIDGIDメーカーR84230の使用説明書/サービス説明書
ページ先へ移動 of 18
1 Y our impact driver has been engineer ed and manufactured to our high standar ds for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance.
2 n Introduction ..................................................................................................................................................................... 2 n General Safety Rules ...........................................
3 GENERAL SAFETY RULES WARNING! RE AD AN D UN DER ST AND ALL INST RU CT ION S. Failure to follow all instructions listed below , may r esul t in elect ric sho ck, fir e and /or ser ious person al injury . SA VE THESE INSTRUCTIONS WORK AREA n Keep your work area clean and well lit.
4 SERVICE n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. GENERAL SAFETY RULES n When servicing a tool, use only identical replacement parts.
5 SAFETY RULES FOR CHARGER WARNING! RE AD AN D UN DER ST AND ALL INST RU CT ION S. Failure to follow all instructions listed below , may r esul t in elec tri c shock , fir e and /or seriou s pers ona l injury .
6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Pr oper interpr eta- tion of these symbols will allow you to operate the tool better and safer .
7 SYMBOLS The following signal words and meanings ar e intended to explain the levels of risk associated with this product. Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury . Indicates a p otentially hazardous situation, which, if not avoided, could result in death or serious injury .
8 4-1/8 in. FEA TURES Fig. 1 COUPLER SWITCH TRIGGER BA TTER Y P ACK BIT STORAGE DIRECTION OF ROT A TION SELECTOR (FORWARD/REVERSE/CENTER LOCK) CHARGER PRODUCT SPECIFICA TIONS Coupler ......................................................... 1/4 in. Keyless Motor .
9 WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. Failur e to do so could result in possible serious personal injury . WARNING: Do not attempt to modify this tool or cr eate accessories not recommended for use with this tool.
10 OPERA TION Fig. 2 WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict sever e injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating tools.
11 OPERA TION Ready to char ge battery pack When batter y pack reac hes cooled temperature, charger begins fast char ge mode W h e n b a t t e r y p a c k r e a c h e s warmed temperature, charger beg.
12 OPERA TION TO INST ALL BA TTER Y P ACK See Figure 4. n Pla ce the bat ter y pac k in the impact driv er, alig ning rais ed rib on battery pack with groove in the driver’s battery port. n Make sure the latches on each side of the battery pack snap into place and the battery pack is secured to the impact driver before beginning operation.
13 OPERA TION DIRECTION OF ROT A TION SELECTOR See Figure 6. The direction of bit rotation is reversible and is contr olled by a selector located above the switch trigger . With the impact driv er held in norm al oper ating posit ion, the dir ect ion of rot a- tion selector should be positioned to the left of the switch trigger for driving.
14 Fig. 8 OPERA TION WARNING: Do not drive a screw where there is likely to be hidden wiring behind the surface. Contact with a “l ive ” wi r e wil l make expo se d me tal par ts of the too l “live” and shock the operator .
15 MAINTENANCE WARNING: W h e n s e r v i c i n g u s e o n l y i d e n t i c a l R I D G I D replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
16 NOTES.
17 W ARRANTY Proof of pur chase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
18 983000-788 7-05 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www .
デバイスRIDGID R84230の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID R84230をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID R84230の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID R84230の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID R84230で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID R84230を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID R84230の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID R84230に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID R84230デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。