Rockford Fosgateメーカー2300の使用説明書/サービス説明書
ページ先へ移動 of 28
® ® 2300 / 2600 X / 4600 X A MPLIFIERS O WNER ' S M ANUAL Seri es 1.
Dear Customer, Congratulations on your purchase of America’s finest brand of car audio amplifiers. At Rockford Fosgate we are committed to musical reproduction at its best, and we are pleased you chose our product.
T ABLE OF C ONTENTS Specifications .................................................................................... 1 Introduction ...................................................................................... 3 Operating Features ........
– 1 – S PECIFICA TIONS Series 1 2300 Series 1 2600x Series 1 4600x Dynamic Power Rating (IHF 202 Standard) - Measured at 14.4 Voltage 1 Bridged/Mono into a 4 Ω Load 90 Watts 180 Watts 180 Watts .
– 2 – Series 1 2300 Series 1 2600x Series 1 4600x Signal-to-Noise Ratio Over 105 dB A weighted Bandwidth 10 Hz to 100 kHz ± 3dB Damping Factor @ 4 Ω At output connector - Over 200 Frequency Response 20 Hz to 20 kHz ± 0.5dB IM Distortion (IHF) Less than 0.
– 3 – I NTRODUCTION This manual provides information on the features, installation and operation of the Series 1 2300, 2600x and 4600x Amplifiers. We suggest you save this manual for future reference. We strongly recommend you have your Authorized Rockford Fosgate Dealer and Service Center install your new Series 1 amplifier.
Gold-Plated Connectors – of high quality to provide lower resistance and better reliability. Series 1 Housing – The extruded aluminum heatsink design of the Series 1 was designed for high performance cooling. – 4 – 2. for 4600x model 1. 3. 4. 1.
GND AP B+ +R – +L – – R+ – L+ Bridged Bridged – + – + – 5 – for 4600x model 5. Power/Speaker Connectors The gold-plated terminal block connectors are: GND Supplies ground to the amplifier.
I NST ALLA TION C ONSIDERA TIONS – 6 – This section focuses on some of the vehicle considerations for installing your new Series 1 amplifier. Checking your battery and current sound system, as well as pre-planning your system layout and best wiring routes will save installation time.
– 7 – T OOLS & S UPPLIES N EEDED Wire Cutters Phillips Screwdrivers Wire Strippers Flat Blade Screwdrivers Wire Crimpers Battery Post Wrench Voltmeter Electric Hand Drill with assorted bits Power Wire - [10-12 AWG; approx. 17’ (518.72 cm)] Grounding Wire - [10-12 AWG.
– 8 – P ASSENGER M OUNTING Under the seat or floor mounting will work as long as there is a minimum of 1” (2.5 cm) of air gap above the amplifier heatsink. Vertical mounting of the amplifier is still the best. Caution! Be sure to avoid running the power wires near the low level input cables, antenna, sensitive equipment or harnesses.
– 9 – 4. Input – The amplifier ’ s signal input RCA jacks should be con- nected to the source unit ’ s signal outputs with high-quality braided or double-shielded interconnecting RCA cables. Note: Be sure to route the Series 1 signal input cable away from the main power wire and the car ’ s wiring harnesses to avoid noise coupling.
– 10 – A CTIVE C ROSSOVER M ODE S ELECTIONS FOR THE 2600 X AND 4600 X The Series 1 2600x and the 4600x amplifiers feature a selectable electronic crossover. One module controls two output channels that can be configured in a High-Pass, Low-Pass, or Full Range (factory default) position.
– 11 – W IRING D IAGRAMS - 2300 / 2600 X 2300/2600 X B ASIC S YSTEM –+ Seri es 1 2300 2600x – + Source Unit 4 Ω (2 Ω min.) Right Full Range 4 Ω (2 Ω min.) Left Full Range *Xover Module (2600x only) Full Range Position GND AP B+ – L + – R + *See page 10 for proper crossover use.
– 12 – 2300/2600 X 3-W AY S TEREO /M ONO S YSTEM – + – + • • • • MX MX + – TX – + TX • • – + Source Unit Seri es 1 2300 2600x *Xover Module (2600x only) Full Range Position – R + – L + GND AP B+ Tweeter Tweeter 4 Ω Right Midrange 4 Ω Left Midrange 6.
– + – + • • • – + + – TX TX MX MX – + Seri es 1 2600x • Seri es 1 2600x – 13 – See page 10 for proper crossover use. 2600 X 3-W AY B I -A MPLIFIED S YSTEM Source Unit High Pass L.
W IRING D IAGRAMS - 4600 X – 14 – The following pages show some examples for wiring the Series 1 4600x amplifier to your vehicle's speaker system.
– 15 – 4600 X 3-W AY M ULTI -C HANNEL S TEREO /B RIDGED M ODE See page 10 for proper crossover use. + – – + + – • • • • TX – + TX – + GND AP B+ +R – +L – – R+ – L+ Bridge.
– 16 – 4600 X 2 C HANNEL B RIDGED L OW P ASS See page 10 for proper crossover use. Source Unit + – – + GND AP B+ +R – +L – – R+ – L+ Bridged Bridged Seri es 1 4600x LEFT RIGHT POWER LE.
–17 – T ROUBLESHOOTING This troubleshooting guide is intended to assist you with certain problems which may occur. If you still encounter problems, see your Authorized Rockford Dealer for assistance. Problem Amplifier will not play — Remote Turn-on light is off.
Problem Amplifier gets too hot. Solution 1. Be sure the amplifier is properly mounted. You should be able to place your hand a few inches above the amplifier housing and feel the heat rising when the unit is on. Hot air rises. Consequently mount the amplifier with the heatsink fins aligned vertically.
Problem Engine Noise (Whine) Solution 1. Disconnect the speakers from the amplifier. Connect a test speaker to the amplifier output terminals. If the noise goes away, check your speaker leads, speakers and crossovers. 2. If the noise persists, use a “ shorting plug ” to mute the input signal at the amplifier.
D YNAMIC P OWER M EASUREMENTS – 20 – Appendix A About the Dynamic Power Measurements The Audio Graph PowerCube is a test instrument used to measure the output of an amplifier. It makes measurements in accordance with IHF- 202 standards. The IHF-202 standard is a Dynamic power measurement.
– 21 – Information Cubed The data acquired in the testing procedure is then graphed in the form of a 3-dimensional cube, hence the name PowerCube . The Phase Angle is expressed on the horizontal axis, the Output Voltage is presented on the vertical axis and the Impedance is displayed on the Z axis.
W ARRANTY I NFORMA TION – 22 – Rockford Fosgate warrants all electronics to the original consumer/purchaser to be free from defects in materials or workmanship for a period of three (3) years. We will cover parts and labor provided the product was purchased from an Authorized Rockford Fosgate Dealer.
N OTES.
N OTES.
REV. C 1/94 MAN-0191 Rockford Fosgate A Division of Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (602) 967-3565 In Canada, call Korbon (905) 567-1929 In Europe,.
デバイスRockford Fosgate 2300の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rockford Fosgate 2300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRockford Fosgate 2300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rockford Fosgate 2300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rockford Fosgate 2300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rockford Fosgate 2300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRockford Fosgate 2300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rockford Fosgate 2300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRockford Fosgate 2300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。