Rockford Fosgateメーカー240X4の使用説明書/サービス説明書
ページ先へ移動 of 40
®® I NST ALLA TION & O PERA TION M ANUAL ® trans • ana 4 ® trans • ana 4 -C HANNEL A MPLIFIERS.
.
Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are committed to musical reproduction at its best, and we are pleased you chose our product.
T ABLE OF C ONTENTS Introduction ...................................................................................... 1 Punch 4-Channel Amplifier Accessory Pack ...................................... 1 Rockford Fosgate Accessories ..................
I NTRODUCTION The Punch 160x 4 and 240x 4 are 4-channel amplifiers which can deliver 160 watts and 240 watts RMS respectively. Both ampli- fiers utilize a 2/4-channel input switch to eliminate the need for signal splitters.
R OCKFORD F OSGA TE A CCESSORIES The following accessories were designed to enhance the perfor- mance of the Punch 160x 4 and 240x 4 amplifiers. Energy Storage Capacitor The Punch capacitors are used to provide extra current needed by amplifiers to reproduce musical transients.
T ECHNICAL D ESIGN F EA TURES – 3 – ◆ T RANS•ANA ( T RANSconductance Active Nodal Amplifier) The TRANS • ANA ( T RANSconductance Active Nodal Amplifier) is a circuit that allows the audio signal to pass through the amplifier at low voltage .
◆ DSM (Discrete Surface Mount) Technology The DSM (Discrete Surface Mount) manufacturing process com- bines the advantages of both discrete components and integrated circuitry. Rockford Fosgate is the only American amplifier manu- facturer to have invested millions into this process.
◆ RTP (Real Time Protection) NOMAD (NOn-Multiplying Advanced Decision) The Punch and Power amplifiers use an analog computer process to maximize safe output power under all operating conditions. Rock- ford Fosgate pioneered and developed RTP (Real Time Protection), a crucial element in the performance edge of our amplifiers.
D ESIGN F EA TURES 1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.
6. RCA Input Jacks – The industry standard RCA jacks provide easy connections for signal level input. They are gold-plated to resist the signal degradation caused by corrosion. 7. Signal Input Switch – This switch allows selection of 2-channel or 4-channel source unit feed.
I NST ALLA TION C ONSIDERA TIONS This section focuses on some of the vehicle considerations for installing your new Punch amplifier. Checking your battery and present sound system, as well as pre-planning your system layout and best wiring routes will save installation time.
M OUNTING L OCA TION The mounting location and position of your amplifier will have a great effect on its ability to dissipate the heat generated during normal operation. The design of our cast aluminum heatsink serves to easily dissipate the heat generated over a wide range of operating condi- tions.
Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system.
3. Punch 160x 4 Trim the power cable to within 18" of the battery and install the protective rubber boot packed with the fuseholder over the end of the wire. Strip 3/8" of insulation from the wire and insert it into the end of the fuseholder, then crimp it in place.
6. Prepare the REM turn-on wire for connection to the amplifier by stripping 5/8" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source.
U SING THE XC ARD The crossover functions are controlled through the use of an XCard and can be set for high-pass, low-pass or full range operation. Each crossover card has two faces: one face operates Full Range , the other has arrows to indicate the edge for selecting HP (high-pass) or LP (low-pass) operation.
U SING THE S IGNAL I NPUT S WITCH 2-Channel Input Input 1 2 Rear XCard Front XCard + L– + R– LR LR – R+ – L+ 4-Channel Input + L– + R– L F R F 12 – L+ – R+ LR R R Input Rear XCard Fron.
B ASIC C ONNECTIONS *Keep grounds as short as possible. Power Connections REM Power Connect to remote turn-on lead of source unit Connect to B+ of battery with proper fuse Connect to chassis ground of.
Stereo Operation +L– +R– Input 2-Ch. { + – + – Rear XCard Front XCard 4 ohm 4 ohm *Note: XCard can be inserted in HP , LP , or Full Range Rear XCard* Front XCard* LP LP 2-Channel Input – R +.
Mono Operation + L– + R – Input 2-Ch. { + – + – Rear XCard Front XCard 4 ohm 4 ohm *Note: XCard can be inserted in HP , LP , or Full Range Rear XCard* Front XCard* LP LP 2-Channel Input – L+.
3-Channel Operation Note: Invert the speaker wire polarity (+ and – ) on the rear channels if XCard for front channel is set to HP and XCard for rear channel is set to LP (or vice versa).
4-Channel Stereo Operation + – 2 ohm + – 2 ohm + L – 2-Ch. { + – Rear XCard Front XCard 2 ohm *Note: XCard can be inserted in HP , LP , or Full Range Rear XCard* Front XCard* HP HP 2-Channel I.
4-Channel Stereo/Single Bridged Operation • RCAs are connected to front or front and rear inputs • Signal Input Switch is set to 2-channel or 4-channel input • Gain for front and rear operates i.
– + 2 ohm – + 2 ohm + L – 2-Ch. { + – Rear XCard Front XCard 2 ohm *Note: XCard can be inserted in HP , LP , or Full Range Rear XCard* Front XCard* FULL FULL 2-Channel Input Rear XCard Front XCard *Note: XCard can be inserted in HP , LP , or Full Range Rear XCard* Front XCard* FULL FULL 4-Channel Input – L+ – R+ + R – + – 4-Ch.
S YSTEM D IAGRAMS 80 Watt 3-Way System ® PWR-812 Front Rear ® trans • ana + – + – 12dB/octave LP 20Hz - 100Hz RF A-414 12dB/octave HP 100Hz - 20,000Hz 2X-4 2X-4 RF A-414 + – + – + – + .
80 Watt 4-Way System RF A-414 ® PWR-812 Front Rear 12dB/octave HP 6dB/octave LP 100Hz - 275Hz 12dB/octave LP 20Hz - 100Hz 2X-4 ® trans • ana + – + – 2X-4 RF A-414 6dB/octave HP 275Hz - 20kHz .
200 Watt 4-Way System ® trans • ana PWR-812 Front Rear 12dB/octave LP 20Hz - 100Hz + – + – ® ® trans • ana ® RF A-414 12dB/octave HP 100Hz - 20,000Hz 2X-4 2X-4 RF A-414 RF A-414 2X-4 2X-4 .
300 Watt 4-Way System RF A-414 2X-4 2X-4 RF A-414 12dB/octave HP 100Hz - 20,000Hz Front Rear ® ® trans • ana RF A-414 12dB/octave HP 100Hz - 20,000Hz 2X-4 2X-4 RF A-414 ® trans • ana ® 4 12dB/.
T ROUBLESHOOTING Amplifier does not turn on (Power LED is off) Symptom Diagnosis Remedy Voltage applied to the REM terminal of the amplifier is not between 10.5 and 15.5 volts or there is no voltage present. Voltage to the B+ termi- nal of the amplifier is not between 10.
Speaker Output Low or Distorted Readjust input gains of amplifier. Check system with known working source and repair or replace original source as needed. Check XCard position and repair or replace as neces- sary. Check the alternator, bat- tery, fuse, and power and ground wiring.
Noise is radiating into RCA signal cable. Bad component in the sig- nal chain. Noise is radiating into speaker cables. Multiple grounds in the audio system. Ground loop between source unit and antenna. Engine Noise Symptom Diagnosis Remedy Check connections, run the RCA cables on a different route away from sources of high voltage.
D YNAMIC P OWER M EASUREMENTS About the Dynamic Power Measurements The Audio Graph PowerCube is a test instrument used to measure the output of an amplifier in accordance with IHF-202 industry stan- dards.
Information Cubed The data acquired in the testing procedure is then graphed in the form of a 3-dimensional cube. Hence the name PowerCube . The Phase Angle is expressed on the horizontal axis, the Output Voltage is presented on the vertical axis and the Impedance is displayed on the Z axis.
160 X 4 S PECIFICA TIONS Continuous Power Rating (Competition Standard) – Measured at 13.8V RMS continuous power per channel , all channels 20 Watts driven into a 4 Ω load from 20-20,000Hz with less than 0.
Continuous Power Rating (Competition Standard) – Measured at 13.8V RMS continuous power per channel , all channels 30 Watts driven into a 4 Ω load from 20-20,000Hz with less than 0.05% Total Harmonic Distortion (THD) RMS continuous power per channel , all channels 60 Watts driven into a 2 Ω load from 20-20000Hz, with less than 0.
W ARRANTY I NFORMA TION Rockford Fosgate warrants all electronics to the original consumer/purchaser to be free from defects in materials or workmanship for a period of three (3) years. We will cover parts and labor provided the product was purchased from an Authorized Rockford Fosgate Dealer.
N OTES.
N OTES.
Rockford Fosgate Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (602) 967-3565 In Europe, Fax (49) 4207-801250 In Japan, Fax (81) 559-79-1265 6/95 MAN-0989-B.
デバイスRockford Fosgate 240X4の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rockford Fosgate 240X4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRockford Fosgate 240X4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rockford Fosgate 240X4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rockford Fosgate 240X4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rockford Fosgate 240X4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRockford Fosgate 240X4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rockford Fosgate 240X4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRockford Fosgate 240X4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。