Rockford Fosgateメーカー250.2の使用説明書/サービス説明書
ページ先へ移動 of 61
punch competition Power amplifiers Operation & Installation 250. 1 250. 2 ® ® car audio fanatics for ® power power new chrome heatsink.
Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product.
T ABLE OF C ONTENTS Introduction ................................................................................................................................................................. 1 Punch Accessory Pack .................................
– 1 – P UNCH A MPLIFIER A CCESSORY P ACK The accessory pack shipped with the “250 series” Power amplifiers include the mounting hardware necessary to secure the ampliifer to the vehicle and to attach the end caps to the amplifier. Punch Power 250.
– 2 – T ECHNICAL D ESIGN F EA TURES Many of the solutions to common design problems encountered by Rockford Fosgate engineers created entire new circuit designs as well as new ways to construct the Punch 250.
– 3 – ◆ DSM (Discrete Surface Mount Technology) The DSM ( D iscrete S urface M ount) manufacturing process combines the advantages of both discrete components and integrated circuitry. Rockford Fosgate is the only American amplifier manufacturer to have invested millions into this process.
– 4 – Differential inputs only amplify the difference between two conductors. Note: the noise spikes appear on both the center conductor and the outer shield and therefore are not amplified. Center Conductor Outer Shield RCA Input Differential Input Figure 2 ◆ Balanced Line Inputs (250.
250. 2 D ESIGN F EA TURES 1. Cast Aluminum Chrome Heatsink – The cast aluminum heatsink of the Punch Power amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.
10. Input Sensitivity Controls – The input level controls are preset to match the output of most source units. They can be adjusted to match output levels from a variety of source units. 11. Internal Crossovers – These built-in crossover cards are configurable for a multitude of operating frequencies.
250. 1 D ESIGN F EA TURES 1. Cast Aluminum Chrome Heatsink – The cast aluminum heatsink of the Punch Power amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.
10. Internal Crossover – This built-in crossover card is configurable for a multitude of operating frequencies. The orientation of the card in its socket determines the function of high-pass, low-pass or full range operation. 11. Phase Switch – This switch enables you to easily invert the phase without having to disconnect the speaker wires.
– 9 – I NST ALLA TION C ONSIDERA TIONS T ools Needed The following is a list of tools you will need for installing the “250 Series” Power amplifiers: Allen wrenches 9/64" & 3/32".
M OUNTING L OCA TION S The mounting location and position of your amplifier will have a great effect on its ability to dissipate the heat generated under normal operation. The design of our cast aluminum heatsink serves to easily dissipate the heat generated over a wide range of operating conditions.
W IRING T HE S YSTEM CAUTION: Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system. 1. Configure the internal XCard crossovers prior to installation.
U SING P ASSIVE C ROSSOVERS A passive crossover is a circuit that uses capacitors and/or coils and is placed on speaker leads between the amplifier and speaker. The crossover delegates a specific range of frequencies to the speaker for optimum driver performance.
T ABLE OF C ROSSOVER C OMPONENT V ALUES 6dB/Octave Low-Pass 6dB/Octave High-Pass Freq. Hertz Speaker Impedance 80 4.1mH 1000 µ F 8.2mH 500 µ F 16mH 250 µ F 100 3.1mH 800 µ F 6.2mH 400 µ F 12mH 200 µ F 130 2.4mH 600 µ F 4.7mH 300 µ F 10mH 150 µ F 200 1.
U SING THE XC ARD The crossover functions are controlled through the use of an XCard and can be set for high-pass, low-pass or full range operation. The XCard shipped with your amplifier is set for Full Range.
– 15 – XC ARD R ESISTOR C HART Frequency R1 R2 20Hz 169k Ω 169k Ω 25Hz 133k Ω 133k Ω 30Hz 110k Ω 110k Ω 35Hz 95.3k Ω 95.3k Ω 40Hz 84.5k Ω 84.5k Ω 45Hz 75k Ω 75k Ω 50Hz 68.1k Ω 68.1k Ω 55Hz 61.9k Ω 61.9k Ω 60Hz 56.2k Ω 56.
250. 2 I NST ALLA TION – 16 – *Keep wire as short as possible. 250. 2 Power Connections (Option #1) 250. 2 Power Connections (Option #2) *Keep wire as short as possible. I N S T A L L A T I O N ® ® REM Power Connect to remote turn-on lead of source unit.
– 17 – • RCA inputs are connected to both left and right channels • Signal Input Switch selected to Unbalanced for RCA input • Left Phase Switch set to 0 ° • Right Phase Switch set to 180.
– 18 – • RCA inputs are connected to both left and right channels • Signal Input Switch selected to Unbalanced for RCA input • Left Phase Switch set to 0 ° • Right Phase Switch set to 180.
– 19 – U SING THE 250. 2 S IGNAL S WITCHING N ETWORK The Punch 250. 2 Power amplifier has a crossover switching network which enables you to: • “Audiophile Bypass” the 250. 2 and Pass-Thru • Configure a 12dB per octave filter for both 250.
– 20– XCard 1 XCard 2 XCard not required. • 250. 2 bypasses the circuitry of XCard 1 and XCard 2 • Pass-Thru bypasses the circuitry of XCard 1 and XCard 2 • The 250.
– 21 – • 250. 2 uses output from XCard 1 • Pass-Thru uses output from XCard 2 Configure a 12dB per octave filter for both the 250. 2 and Pass-Thru. I N S T A L L A T I O N ® ® XCard 1 XCard 2 250x 2 2 XCard* Pass Thru XCard* HP LP Unbal. Pass Thru Bal.
– 22 – XCard 1 XCard 2 LP Pass Thru XCard XCard not required. “Audiophile Bypass” the 250. 2 and configure a 12dB per octave filter for the Pass-Thru. • 250. 2 bypasses the circuitry of XCard 1 • Pass-Thru uses output from XCard 2 • The 250.
– 23 – Configure a 12dB per octave bandpass filter for the 250. 2 and “Audiophile Bypass” the Pass-Thru. Configure a 24dB per octave filter for the 250. 2 and “Audiophile Bypass” the Pass-Thru. I N S T A L L A T I O N ® ® *Note: Both XCard inserted as HP or LP.
The Balanced Line Inputs can be utilized with the optional Balanced Line Transmitter. Unlike standard RCA cables that use two wires to carry the audio signal and ground, balanced lines use three. In a balanced line, the output signal and its inverted replica travel down a pair of wires where the ground connects via the shield.
– 25 – Level Setting the BLT • Disconnect Speaker(s) from the 250. 2 • CD Software used to set levels is a test tone of 1kHz at “0dB” or “All Bits High” • Source Unit set to 3/4 volu.
250. 1 I NST ALLA TION – 26 – 250. 1 Power Connections (Option #1) + – 250. 1 Power Connections (Option #2) + – *Keep ground connections as close to each other as possible. Less than 18" Less than 18" *Keep ground connections as close to each other as possible.
– 27 – Mono Operation • Signal Input Switch set to L+R for RCA input • Phase Switch set to 0 ° • Impedance should be 2 Ω minimum • XCard can be set for High-Pass , Low-Pass or Full Rang.
– 28 – • Signal Input Switch (250. 1 #1 / #2) set to L(Mono) for single RCA input ) • Phase Switch (250. 1 #1/2) set to 0 ° • Impedance for each amplifier should be 2 Ω minimum • XCard for each amplifier can be set for High-Pass, Low-Pass or Full Range Stereo Operation using two Punch 250.
– 29 – Stereo/Mono Operation I N S T A L L A T I O N ® ® 250. 1 #2 250. 1 #1 – + RCA Input + – LR +– R Pass Thru L Pass Thru Power Gain X-Over 24dB/12dB/0dB L + R / L (Mono) RCA Inputs 0 .
– 30 – Bridged Mono Operation I N S T A L L A T I O N ® ® 250. 1 #2 250. 1 #1 RCA Input +– Power Gain X-Over 24dB/12dB/0dB L + R / L (Mono) RCA Inputs 0 ° -180 ° Speaker – + L (Mono) R 4 .
U SING THE 250. 1 S IGNAL S WITCHING N ETWORK – 31 – • Xover is set to 0dB • The 250. 1 is in Audiophile Bypass mode which maintains signal integrity resulting in a better sounding amplifier • Pass-Thru has Full Range output only • The XCard does not need to be inserted to allow the 250.
– 32 – • Xover is set to 12dB • Pass-Thru has Full Range output only Configure a 12dB per octave filter for the 250. 1 I N S T A L L A T I O N ® ® – + 20Hz 20kHz Full Range +– Power Gain.
– 33 – Configure a 24dB per octave filter for the 250. 1 • Xover is set to 24dB • Pass-Thru has Full Range output only • By switching the crossover to 24dB, the signal is routed through the .
S YSTEM D IAGRAMS – 34 – 250 W att System (rated @ 4 ohms) Total Power Delivery (RMS) Tweeters 450 Watts Midrange 450 Watts PWR-14X PWR-54 4 Ω 80Hz HP 80Hz HP PWR-14X TX-4183 TX-4183 18dB/octave HP 3kHz-20kHz 18dB/octave HP 3kHz-20kHz 24dB/octave HP 80Hz-20kHz PWR-14X PWR-54 4 Ω PWR-14X TX-4183 TX-4183 24dB/octave HP 80Hz-20kHz 250.
– 35 – 500 W att System (rated @ 4 ohms) Total Power Delivery (RMS) Tweeters 450 Watts Midrange 450 Watts Woofers 500 Watts • A sub-sonic filter is a high-pass filter that limits the input signal below a certain motion below that frequency. At very low frequencies a woofer has no output, just motion.
• A sub-sonic filter is a high-pass filter that limits the input signal below a certain motion below that frequency. At very low frequencies a woofer has no output, just motion. If you try to drive this woofer at these lower frequencies, the woofer could self-destruct.
1000 W att System (rated @ 4 ohms) Total Power Delivery (RMS) Tweeters 450 Watts Midrange 450 Watts Midbass 250 Watts Woofers 1000 Watts • A sub-sonic filter is a high-pass filter that limits the input signal below a certain motion below that frequency.
R OCKFORD F OSGA TE A CCESSORIES ® Balanced Line T ransmitter (FG-BL T) The Balanced Line Transmitter converts signal RCA cables from the source unit to balanced signals. The BLT improves sound quality in the system by eliminating noises generated by vehicle electrical systems.
® XCard Crossovers Additional crossover card frequencies are available for specialized requirements. You can get the following XCards from your Authorized Rockford Fosgate Dealer. Energy Storage Capacitors Energy Storage Capacitors are used to provide extra current needed by amplifiers to reproduce musical transients.
Symptom Diagnosis Remedy T ROUBLESHOOTING Amplifier does not turn on. (Power LED is off) Voltage applied to the REM terminal of the amplifier is not between 10.5 and 15.5 volts or there is no voltage present. Voltage to the B+ terminal of the amplifier is not between 10.
– 41 – Symptom Diagnosis Remedy Speaker Output Low or Distorted Input gain(s) for amplifier incorrectly set. Source unit output too low or source unit has no output. Phase selection of amplifier incorrectly se- lected or speakers wired out of polarity from the left to right channel.
Input gain(s) for amplifier incorrectly set. Source unit output too low. XCards are missing or not placed properly in crossover slots and/or switches are not properly selected. Low battery voltage or large voltage drops to the amplifier under load. RCA cable or amplifier connected to Pass- Thru output is defective.
A UTOSOUND 2000's Q UICK C HECK FOR T ROUBLESHOOTING C AR A UDIO S YSTEMS Preface: All audio systems exhibit noise; however , if the level of noise is low enough, and the signal level high enough, noise should not be a problem.
III. MOVE THE DECK. If you're at this step, it's time to turn your system into an “amplified deck” by temporarily relocating the deck right ON TOP of the clean amplifier . Then using very , very short signal cables, connect the output of the deck into the input of the amp and test for noise.
–60 ° (Cap) 0 ° (Ind) +60 ° 1 Ω 2 Ω 4 Ω Impedance 8 Ω 10V 30V 50V 8 Ω –60 ° –30 ° 0 ° 30 ° 60 ° 4 Ω –60 ° –30 ° 0 ° 30 ° 60 ° 2 Ω –60 ° –30 ° 0 ° 30 ° 60 .
– 46 – 250. 2 S PECIFICA TIONS Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4V Per channel into a 4 Ω load 180 Watts Per channel into a 2 Ω load 310 Watts Bridged into a 4 Ω load 620 Watts Continuous Power Rating (Competition Standard) - Measured at 13.
250. 1 S PECIFICA TIONS – 47 – Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4V Mono into a 4 Ω load 420 Watts Mono into a 2 Ω load 710 Watts Bridged (using 2 Punch 250m) into a 4 Ω load 1420 Watts* Continuous Power Rating (Competition Standard) – Measured at 13.
– 48 – L IMITED W ARRANTY I NFORMA TION Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: • Length of Warranty 3 years on electronics 90 days on.
I NFORMA TION I NTERNA TIONAL – 49 –.
LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTALACIÓN DEL PRODUCTO. EVITARA POSIBLES DAÑOS A VD., AL VEHÍCULO O AL PRODUCTO. Los amplificadores de “la serie 250” representan lo ultimo y mejor que Rockford Fosgate puede ofrecerle.
Operación mono/estéreo • Los conectores de entrada RCA se conectan a ambos canales derecho e izquierdo • El conmutador de señal de entrada se colocara en Unbalanced par a las entradas RCA • E.
ATTENTION: Veuillez lire les instructions suivants pour l'nstallation de ce produit. Ne pas les suivre pourrait causer des blessures ou endommager le véhicule. La série d'amplificateurs Power 250 est la vitrine technologique de Rockford Fosgate.
Opération stéréo/mono (Tri- mode) • Les entrées RCA sont connectées aux canaux gauche et droit • L'interrupteur “Signal Input” doit se trouver dans la position “Unbalanced” pour .
Bitte lesen Sie diese Gebrauchsanleitung zuerst sorgfältig durch. Das kann Sie vor dem falschen Einsatz, Ausfallen oder sogar Beschädigung des Produktes oder Ihres Fahrzeuges schützen.
Stereo/Mono Betrieb • Chinch Eingänge des rechten und linken Kanales anschlieben • Signal Eingangsschalter auf “unbalanced” für den Betrieb mit Chinch-Kabel stellen • Linken Phasen Schalte.
PREGO LEGGERE LE SEGUENTI ISTRUZIONI PER L'INSTALLAZIONE DI QUESTO PRODOTTO, IL NON SEGUIRLE POTREBBE RISULTARE SERIAMENTE DANNOSO PER LA PERSONA O PER IL VEICOLO.
Stereo/Mono Operation • RCA inputs non sono collegati ad entrambi, i canli destro e sinistro • Interruttore di segnale input selezionato per il non bilanciamento per l'input RCA • Fase sinistra dell'interruttore posizionata su 0 ° .
Rockford Fosgate Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (602) 967-3565 In Europe, Fax (49) 4202-9750-50 In Japan, Fax (81) 559-79-1265 MAN-1529-B 10/97 MADE IN THE USA This product is designed, developed and assembled in the USA by a dedicated group of American workers.
デバイスRockford Fosgate 250.2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Rockford Fosgate 250.2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRockford Fosgate 250.2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rockford Fosgate 250.2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rockford Fosgate 250.2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rockford Fosgate 250.2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRockford Fosgate 250.2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rockford Fosgate 250.2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRockford Fosgate 250.2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
