RolandメーカーTD-8KVの使用説明書/サービス説明書
ページ先へ移動 of 16
Owner's Manual Thank you, and congratulations on your choice of the TD-8KV Roland Drum System. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 2–3) and “IMPORTANT NOTES” (p. 4). These sections provide important information concerning the proper operation of the unit.
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002d • Do not open or perform any internal modifi- cations on the unit or its AC adaptor.
3 014 • Do not drop the unit! ................................................................................................ • To avoid personal injury and/or damage to the unit, do not touch anything inside the frame of the PD-80 and PD-80R. ..
4 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temper- ature extremes.
5 Getting Started Check the Contents of the Box ❑ TD-8 (Percussion Sound Module) x 1 ❑ KD-80 (V-Kick Trigger) x 1 ❑ FD-6 (Hi-Hat Control Pedal) x 1 ❑ PD-80R (V-Pad) x 1 ❑ PD-80 (V-Pad) x 3 .
6 These strips are 7.5 mm and 7 mm in length. Use them for adjusting the head tension. 7.5 mm 7 mm About the Mesh Head Adjusting the Head Tension • On the KD-80, PD-80R, and PD-80, adjusting the head tension affects only the head response, and does not change the pitch of the sound, as it would on an acoustic drum.
7 Replacing the Head When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: • The head surface is torn • Striking points are no longer detected correctly, even when the head tension is properly adjusted.
8 Setting Pads and Pedals KD-80 (V-Kick Trigger) Before using the KD-80, you need to adjust the head tension (p. 6). Assembling the KD-80 • Take care not to pinch your fingers between the KD-80 pad and the stand plate.
9 KD-80 (V-Kick Trigger) 7. Loosen the T-bolts for the stay and mount the legs on the stay. Install the legs as shown in the figure so that the ends of the legs protrude by about 1 inch (2 cm). fig.K05.e 8. Tighten the T-bolts to secure the legs to the stand.
10 PD-80R/PD-80 (V-Pad) Before using the PD-80R and the PD-80, you need to adjust the head tension (p. 6). fig.P01.j Attaching the Pad to a Stand Attach the PD-80R or PD-80 to a stand (MDS series). fig.P02.j When attaching the PD-80R and the PD-80 to the pad mount, be sure to tighten the stand fixing screw securely.
11 CY-12R/C (V-Cymbal) prevents the cables from catching or getting tangle on the stand. fig.CY-03.e 2. Attach the CY-12R/C so the unit is oriented as shown in the diagram (bolt should be opposite the output jacks). 3. Tighten the wing nut to obtain the desired movement.
12 Choking Choking (pinching) the cymbal ’ s edge with the hand immediately after hitting the cymbal makes the sound stop. To make use of choking play techniques, you ’ ll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots.
13 FD-6 (Hi-Hat Control Pedal) • The tips of the anchor bolts are sharp. Handle with care. • When using on flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. • When the FD-6 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal.
14 Connect the pads and pedals to the TD-8 To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
15 Connect the pads and pedals to the TD-8 About the Included Cables Using the provided cables, connect the pads and pedals to the TD-8. • Carefully refer to the numbers shown in the illustration and connect to the appropriate TRIGGER INPUT jacks on the TD-8 ’ s rear panel.
Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. As of April 1, 2003 (Roland) ARGENTINA Instrumentos Musicales S.
デバイスRoland TD-8KVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Roland TD-8KVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoland TD-8KVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roland TD-8KVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roland TD-8KVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roland TD-8KVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoland TD-8KVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roland TD-8KVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoland TD-8KVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
