RolandメーカーTU-400の使用説明書/サービス説明書
ページ先へ移動 of 21
USER'S MANUAL Thank you very much for purchasing the automatic media take-up unit. • To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location.
ROLAND DG CORPORA TION 1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAP AN 431-2103 MODEL NAME : See the MODEL given on the rating plate. RELEV ANT DIRECTIVE : EC MACHINER Y DIRECTIVE (89/392/EEC).
1 In this manual, the following conventions are used to refer to different models that have items in common. TU-60/70 .............. TU-60 and TU-70 CJ .................... CJ-500 and CJ-400 TU-400/500 .......... TU-400 and TU-500 FJ .................
2 T o Ensure Safe Use Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly . About and Notices Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly .
3 Installation of the control box for the TU is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance. To secure the part in place, use the bolt included with the unit. A loose bolt or use of other than the specified bolt may result in the falling of the part, leading to injury .
4 Do not strike the mirror . Doing so may damage the mirror , resulting in incorrect operation. About the Labels Affixed to the Unit These labels are affixed to the parts shown below . The following figure describes the location. Rating label Use a rated power supply .
5 TUC-60/70 1. System Configuration Use with the configuration shown below . 2. Confirmation of Included Items The items are in the two packing cartons.
6 Frame and Control Box Installation 3. Installation and Assembly Required tool Large Installation of the control box is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance. To secure the part in place, use the bolt included with the unit.
7 (1) (2) Rail Slider Installation Follow steps (1) and (2) in sequence to install the rail slider . Required tool Small Front Required tool Small Installing the Sensor and the Small Retainer If the screw holes for the small cap screws do not line up, loosen all screws at the locations shown in the figure.
8 Power Cord Connection and Large Retainer Installation Arm Installation The configuration of the AC adapter varies according to regional differences in voltage.
9 5. Adjusting the Sensor's Position T urn on the power . T wo LEDs (green and red) light up. 1 Loosen the screw as shown in the figure, and adjust the angle of the sensor so that it is aligned with the mirror . 2 T ighten the adjustment screw securely at the angle where the red LED has gone dark.
10 Return of pulled-out material Material feed Take-up of fed material The CJ/FJ stops operation Take-up of fed material MOTOR ERROR TURN OFF POWER 6. Operating Conditions for the TU The TU takes up material fed from the CJ/FJ.
11 Mounting the Flange and Paper T ube When using the core from used-up rolled material as the paper tube When mounting the paper tube on the flanges, make sure that the paper tube fits snugly . Attempting to take up material when the paper tube is not stable may cause problems such as the pa- per tube coming loose.
12 25 mm (1 in.) or more 25 mm (1 in.) or more FJ T o ensure correct feed, make sure the material pulled out from the roll is free of slack. [Correct] FJ rear [Incorrect] FJ rear Entire material stretched taut Material is slack Loading Rolled Material * For more information, see the user's manual for the CJ/FJ main unit.
13 Pull out material so that it is perpendicular to the paper tube. 1 T o prevent the pulled-out material from becoming crooked, secure with tape at the two edges and center , as shown in the figure.
14 8. Starting Operation Do not allow the hands or hair to touch the paper tube, flange, or sheet during take-up. The hands or hair may become caught. During operation, do not enter the sensor's detection area. Doing so will result in excessive take-up and cause printing to be interrupted.
15 T urn off the power . 1 Cut off the piece of material from the roll. 2 9. Removing Material Removal of taken-up roll material from the TU is a task which must be carried out by two or more persons. Injury may result if attempted by one person without assistance.
16 1 1. What to Do If... The CJ doesn't run * If a message like the one shown at right appears on the CJ Is the cutting function of the application software you're using not enabled? Do not use in such modes. Has the prefeed function on the CJ been set to [ENABLE]? Change the setting to [DISABLE].
17 Acceptable media widths Material weight for which take-up is possible Maximum material diameter after take-up Speed during material take-up Control switches Power consumption Acoustic noise level T.
18 MEMO.
R8-990901.
デバイスRoland TU-400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Roland TU-400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoland TU-400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roland TU-400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roland TU-400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roland TU-400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoland TU-400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roland TU-400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoland TU-400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
