RolandメーカーV-Tour TD-6KWの使用説明書/サービス説明書
ページ先へ移動 of 16
TD-6KW Thank you, and congratulations on your choice of the Roland Drum System TD-6KW. * For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-6V must be adjusted. 202 Copyright © 2006 ROLAND CORPORATION All rights reserved.
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002b • Do not open or perform any internal modifications on the unit.
3 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes.
4 ❑ TD-6V (Percussion Sound Module) x 1 ❑ KD-8 (Kick Trigger Pad) x 1 ❑ FD-8 (Hi-Hat Control Pedal) x 1 ❑ PDX-8 (V-Pad) x 1 ❑ PD-8 (Pad) x 3 ❑ CY-5 (Cymbal Pad) x 1 ❑ CY-8 (Cymbal Pad) x 2 ❑ Connection Cables ❑ Tuning Key x 1 ■ TD-6KW Owner’s Manual x 1 • The tuning key is included in the FD-8 package.
5 USING THE UNIT SAFELY fig.PD-85.e_80 add * Do NOT place your fingers inside the shell, as you may hurt yourself or cause damage to the PDX-8. Or when changing the head, do NOT touch any of the internal parts. Also, do not insert your fingers into the hole of the mounting bracket.
6 USING THE UNIT SAFELY Attach the PDX-8 to a pad mount of the stand. Be sure to tighten the stand fixing screw securel. If it remain loose, double triggering may occur. fig.Stand.e Head Shots fig.HeadShot.e * Do not strike the hoop. Rim Shots fig.RimShot.
7 USING THE UNIT SAFELY When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted.
8 USING THE UNIT SAFELY fig.PD-8.e Attach the PDX-8 to a pad mount of the stand. fig.PD-Set.e When attaching the PD-8s to the mounts, be sure to tighten the stand fixing screws securely. If any of them remain loose, the pad could fall off. fig.PD-HR.e To play the sound assigned to the head, hit only the head.
9 USING THE UNIT SAFELY fig.CY-8.e When mounting the CY-5 on an L-Rod (pad mount), use ONLY the attachment set as shown below. 1. Mounting the lower clutch and the clutch felt (L). Align the notched section as shown below. Then place the clutch felt (L) so it fits securely.
10 USING THE UNIT SAFELY fig.CY-8.e 1. Use a tuning key to tighten the stopper bolt. The stopper keeps the cymbal pad from turning, and prevents the cables from catching or getting tangled on the stand. fig.CY-Set01.e 2. Attach the CY-8 so the Roland logo is positioned on the opposite side of the playing area.
11 USING THE UNIT SAFELY fig.FD-8.e • The tips of the anchor bolts are sharp. Handle with care. • When using on flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. • When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal.
12 USING THE UNIT SAFELY fig.KD-8.e 1. Remove the screws attached to the reverse side of the KD-8’s trigger. fig.KD-Assy01 2. Pull out the stand in the direction indicated by the arrow until it is fully extended. fig.KD-Assy02 3. Use a tuning key to tighten the screws removed in Step 1 so that the stand is firmly secured.
13 USING THE UNIT SAFELY 1. Loosen the stand’s anchor bolts and remove the foot plate. fig.KD-Assy06 2. Set the kick pedal so that the entire bottom surface is attached to the floor. 3. In most cases, the stand becomes somewhat floated. Tighten the anchor bolts securely there to fix the stand and foot plate.
14 USING THE UNIT SAFELY . 921 Using the provided cables, connect the pads. Connect the L-shaped plugs of the included cables to the pads. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
15 USING THE UNIT SAFELY . For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-6V must be adjusted. For more detailed informations, refer to the TD-6KV Owner’s Manual. When adding the new pad, use trigger input 10 (CRASH2).
04234201 2PR As of December 10, 2005 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.
デバイスRoland V-Tour TD-6KWの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Roland V-Tour TD-6KWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoland V-Tour TD-6KWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roland V-Tour TD-6KWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roland V-Tour TD-6KWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roland V-Tour TD-6KWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoland V-Tour TD-6KWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roland V-Tour TD-6KWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoland V-Tour TD-6KWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
