Rubbermaidメーカー1S84の使用説明書/サービス説明書
ページ先へ移動 of 16
RUBBERMAID 7' x 10' 6" RESIN STORAGE BUILDING ASSEMBL Y INSTRUCTIONS Pre-Assembly: • Review the parts list and make sure that no parts are missing. • Review ALL assembly steps before beginning instructions. • Level the area where the shed will be located.
Level construction site before beginning assembly of shed. A foundation may be constructed if desired. 1 FLOOR PLAN: Size the construction site to fit the entire floor . Allow clearance for opening front and back doors. OPTIONAL STEP: If desired, recessed anchor locations (8 places) can be used to anchor the shed floor to a foundation after Step 6.
3 Place the Floor Panel (J-5H51) on the foundation. Connect two Repeat Floor Panels (K-5H52), install Screws (AA) 14 places. Optional Step: If desired, recessed anchor locations (8 places) can be used to secure the Floor to the Foundation, see Step 1.
5 Using a screwdrive r , punch out the screw holes on the top of Left Side Panel (C) 2 places . Connect Left Side Panel (C) into Front Floor (J-5H51). C C Screw Holes click 6 Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap.
9 Using a screwdriver , punch out the screw holes on the top of the Left Side Panel (C) 2 places. Align lap joint between Left Side Panels. Connect Left Side Panel (C) into Repeat Floor (K-5H52). C C C C click 10 Install Wall Connectors (Q) 5 places. 2 1 C C 1 2 C Q C 11 Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap.
13 14 15 16 Lubricate dovetails on Right Back Panel (G) 4 places with liquid soap. Connect Right Back Panel (G) into dovetails of Right Side Panel (D), engage snaps on bottom of Right Back Panel (G) into Repeat Floor (K-5H52). E G D 1 2 1 2 NOTE: Front Gable and Doors not shown.
17 18 19 20 Set the Left Door Panel (AK) face down on the ground. Slide the Hinge Reinforcement (PP) into the hole on the top door pin. The Hinge Reinforcement (PP) will slide in until it is below the end of the door pin.
21 22 23 24 Install Left Door Panel (K) inserting the lower hinge pin into Front Floor (J-5H51) socket, lift the left end of the Gable (M) enough to insert the top hinge pin on Left Door Panel (K) into the Gable (M) socket.
25 26 27 28 Apply Ridge T ape (HH) to Ridge Cap (GG) 2 places. Snap Ridge Cap (GG) onto the Ridge Beam Assembly covering the seam. GG HH HH GG RS RL GG RS RL Place the Ridge Beam Assembly into cups at the top of each Gable (M).
29 30 Align slots in Ridge Beam Assembly with holes in Gable (M) tab, install Bolt (BB), Washer (CC), and Nut (DD) 1 place, ONL Y TIGHTEN NUT “FINGER” TIGHT . Bolt Head Washer Nut Plastic T ab on Gable DD CC BB M M R Using a screwdrive r , punch out the screwholes on the Left Skylight Roof Panel (AN ) 6 places.
Lubricate roof snaps on left side of the front Gable (M) 4 places. Raise the Left Roof Panel (N) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly .
Raise the Left Skylight Roof Panel (AN) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly. Using (2) stepstools (1 inside shed, 1 outside shed), lift the bottom of Left Skylight Roof Panel (AN) above horizontal and guide into the Ridge Beam Assembly .
Install Roof Connectors (T) 8 places. Y ou may need to lift the roof panels to avoid the 2"x6" lumber . 35 T 1 2 2 1 Engage all snaps between the Roof Panels and Gables.
Repeat Steps 29-35 for Right Roof of shed. 37 Install Screws (AA) 16 places in front and back Gable (M). 38 Back of shed shown Caution: When installing screws do not overtighten.
88.09" 128.85" 94.63".
Customer Service T oll Free: 1-888-895-2110 M–F 8:30 AM to 5:00 PM EST or visit us at www .rubbermaid.com 1869756 W e hope you enjoy your Rubbermaid ® 7' x 10' 6" Storage Building! For more information on all Rubbermaid ® products, go to www .
デバイスRubbermaid 1S84の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rubbermaid 1S84をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRubbermaid 1S84の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rubbermaid 1S84の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rubbermaid 1S84で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rubbermaid 1S84を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRubbermaid 1S84の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rubbermaid 1S84に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRubbermaid 1S84デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。