RuncoメーカーVX-2cの使用説明書/サービス説明書
ページ先へ移動 of 36
VX-2c O WNER’S O PERA TING M ANUAL Digital Light Pr ocessing Pr ojector and DHD Contr oller.
1 T ABLE OF CONTENTS Introduction ..................................................................................................................................................... 2 W arnings & Safety Pr ecautions .............................
2 INTRODUCTION » Introduction to the Runco V ideo Xtreme™ VX-2c 3-Chip DLP Projector Runco steps into the future once again with the V ideo Xtreme™ VX-2c projection system. The VX-2c is among the rst DLP™ projectors to offer a 16:9 native resolution, 3-chip system for home theater .
W ARNINGS & SAFETY PRECA UTIONS 3 W ARNING FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufacturer could void the user ’ s authority to operate this equipment. CAUTION: T O PREVENT FIRE OR SHOCK HAZARDS, DO NOT REMOVE COVER.
4 W ARNINGS & SAFETY PRECAUTIONS DECLARA TION OF CONFORMITY RUNCO PROJECTOR, MODEL VX-2c This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) T.
5 LIMITED W ARRANTY Congratulations on your purchase of a Runco video product and welcome to the Runco family! W e believe Runco produces “The W orld’ s Finest Home Theater Products”. W ith proper installation, setup and care, you should enjoy many years of unparalleled video performance.
LIMITED W ARRANTY 6 TO OBT AIN SER VICE, CONT ACT YOUR RUNCO DEALER: Repairs made under the terms of the Limited W arranty covering your Runco International video product will be performed at the loca.
7 PROJECT OR DESCRIPTION PROJECTOR ISOMETRIC VIEW PROJECTOR REAR P ANEL AC Power In DVI Input AC Main Switch Power Button and Status LED Control Panel V acuum Fluorescent Display Intake V ent Exhaust .
DHD CONTROLLER DESCRIPTION FRONT P ANEL 2 3 1 4 5 6 7 8 9 10 1. RUNCO ICON When the Red light is displayed the unit is in Standby , when Blue light is displayed the unit is On. 2. POWER BUTTON Press once to toggle on from Standby mode to On mode, a second time to place into Standby mode.
DHD CONTROLLER DESCRIPTION REAR P ANEL Pb Pr Y Vide o 3 IR RS-232 Control S-Video 1 S-Video 2 HD1 HD2 1 2 Pr R Y G Pb B R Pr G Y B Pb H V DVI 1 DVI 2 DVI Out H/V V H Pr R Y G Pb B H V TRIGGERS RS-232 Ou t CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
REMOTE CONTROL DESCRIPTION (1) ON/OFF Switches Power ON/OFF . (This does not operate when POWER/ST ANDBY indi- cator of the main unit is off.) (2) IR OUTPUT INDICA TOR Illuminates when a button in pressed, indicating that an IR signal is being transmitted.
The VX-2c is designed to receive only digital input signals directly from the companion DHD Controller/Processor . All signal sources should be connected to the appropriate inputs on the rear panel of the DHD. The signal from the DHD is then output to the VX-2c projector through a Runco Proprietary (RP) DVI cable.
QUICK SETUP GUIDE 12 Step I Connection: 1. Connect Power to Both Projector and DHD controller 2. Connect DVI output from the DHD to projector DVI in 3. Connect V ideo (Composite), S-V ideo to1 or 2, Component 480i (RCA) input, HD signals to HD1 or HD2 (BNC), DVI 4.
While there are many different ways to connect your source equipment to your DHD Controller , the examples below are the most common. ANALOG INPUTS: • Composite V ideo Input Composite video is the most common type of signal used, but is also the lowest in picture quality .
14 LENS SHIFT RANGE Lens Option 1: Thr ow Distance 1.2 - 1.4 x Width of Scr een Example: 56” x 100” Screen TD = 120” to 140” lens to screen When only V ertical or only Horizontal Shift is used: Maximum. V ertical Shift ↑ = 60% of screen height (.
15 LENS SHIFT RANGE Lens Option 4: Thr ow Distance 2.35 - 3.60 x Width of Scr een Example: 56” x 100” Scr een TD = 235” to 360” lens to screen When only V ertical or only Horizontal Shift is used: Maximum. V ertical Shift ↑ = 60% of screen height (.
.
17 » PROJECTOR CONTROL Once the VX-2c and DHD controller have been properly installed and connected, you are ready to perform set-up and calibration procedures. All setup and calibration parameters are accessed and adjusted through the VX-2c fluorescent display menu system.
This is the first menu that will appear when “MENU” is selected. The above diagram depicts the main menu. There are five option items in the Main menu: Wt. Balance: Adjusting Contrast, Brightness, and Gamma Orient: Adjusting Picture Orientation (FF , CF , RF , and CR) Lens Adj.
19 MENU DESCRIPTION AND NA VIGA TION Orient Orient Use Prefer ence window to select projector picture orientation From the Main menu use the Up or Down arrow to select “ Orient” and press the Enter button to call up the Orient display . The Orient display allows selection of Picture Orientation options.
20 MENU DESCRIPTION AND NA VIGA TION Pr oj. Info Model S/N Hardware Revision Firmware Revision Error Code From the Main menu use the Up or Down arrow to select “ Proj. Info” and press the Enter button to call up the Status options. There are five options: Model: VX-2c should be displayed.
21 MENU DESCRIPTION AND NA VIGA TION Gain Red Green Blue Gain Indicates you are in the Contrast Setting Menu Red Press ENTER to change the Red Contrast setting by using the UP and DOWN arrows to Incre.
22 MENU DESCRIPTION AND NA VIGA TION Gamma Red Green Blue Gamma Indicates you are in the Gamma Setting Menu Red Press ENTER to change the Red Gamma setting by using the UP and DOWN arrows to Increase .
23 MENU DESCRIPTION AND NA VIGA TION Diagnose Normal Color Enable T ests Diagnose Indicates you are in the Diagnostics menu Normal Press ENTER to return all Diagnostic T ests to their Normal mode Colo.
24 MENU DESCRIPTION AND NA VIGA TION Color Gamut Color Space Color T emp Color Indicates you are in the Color Settings menu Gamut Press ENTER to access the Gamut settings menu Color Space Press ENTER to access the Color Space settings menu Color T emp Press ENTER to access the Color T emperature setting menu Service Power Cycle Standby T ime No.
25 MENU DESCRIPTION AND NA VIGA TION Color Enable Red Green Blue Y ellow Cyan Magenta Color Enable Indicates you are in the Color Enable menu Red Press ENTER to turn Red On Green Press ENTER to turn G.
26 MENU DESCRIPTION AND NA VIGA TION T ests T est Black T est White T est Green T est Red T est Blue Check Board Alignment H Ramp V Ramp T ests Indicates you are In the Internal DLP T est mode T est B.
Color Space Indicates you are in the Color Space setting menu HD Press ENTER to select the HD Color Space SD NTSC Press ENTER to select the SD NTSC Color Space SD P AL Press ENTER to select the SD P A.
28 MENU DESCRIPTION AND NA VIGA TION Manual White Red Green Blue Manual Indicates you are in the Manual Gamut setting mode using a calibrated colorimeter .
BASIC TROUBLESHOOTING TIPS The following is a basic troubleshooting guide that can assist you in resolving typical problems may result in normal operation. If you have encountered problems that are not listed in this guide, please contact your Runco dealer for assistance.
Baud rate: 19200 (xed) Bits: 8 No Parity All protocol in ASCII format RS-232 input connector pin numbers: TxD= Pin# 2, RxD= Pin# 3, GnD= Pin# 5 Command format (single command): command v alue (i.e. brightness 100). NO TE: A space (not an underscore) or comma may be used between the command and its value.
Command Parameter V alue Stored? Description (min/max) POWER 0/1 NA Turns DHD On and Of f ON NA NA Turns DHD Controller on OFF NA NA T urns DHD Controller off COMPOSITE NA YES Selects the Composite vi.
Command Parameter V alue Stored? Description (min/max) IHPOS? NA NA Returns input horizontal position value IHEIGHT? NA NA Returns input vertical height value OHPOS? NA NA Returns output horizontal po.
SPECIFICA TIONS 33 VX-2c PROJECTOR SPECIFICA TIONS Projector T ype: Digital Light Processing™ (DLP™), 3-chip, 16:9 HD-2, DMD™ Native Resolution: 1280 x 720 (16:9) Aspect Ratios: Determined by su.
34 DHD™ DIGIT AL CONTROLLER SPECIFICA TIONS Aspect Ratio: Anamorphic, Letterbox, V irtualWide, 4:3 (on either 16:9 or 4:3 screens) Input Standards: NTSC/P AL Output Resolution: 720P Outputs: (1) HD .
R UMA-010120 8-6-04 v5.0 Runco International 2900 Faber Street Union City , CA 94587 Ph (510) 324-7777 / Fax (510) 324-9300 1-800-23-R UNCO.
デバイスRunco VX-2cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Runco VX-2cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRunco VX-2cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Runco VX-2cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Runco VX-2cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Runco VX-2cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRunco VX-2cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Runco VX-2cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRunco VX-2cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
