Ryobiメーカー705rの使用説明書/サービス説明書
ページ先へ移動 of 26
FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA www .ryobi.com IMPORT ANT MANUAL DO NOT THROW AW A Y 7 0 5 r T r i m m e r P l u s ® OPERA TOR’S MANUAL 2-Cycle Gas T rimmer 7.
THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to-understand operating instructions.
W ARNING! 3 SP ARK ARRESTOR W ARNING CALIFORNIA EMISSION REGULA TIONS NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and W ashington.
RULES FOR SAFE OPERA TION 4 • Clear the area to be cut befor e each use. Remove all such objects such as rocks, broken glass, nails, wir e, or string which can be thrown or become entangled in the cutting attachment. Clear the area of children, bystanders, and pets.
RULES FOR SAFE OPERA TION 5 • Always stop the engine and allow it to cool before filling the fuel tank. Never r emove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pr essure in the tank.
RULES FOR SAFE OPERA TION 6 SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety , assembly , operating and maintenance and repair information.
RULES FOR SAFE OPERA TION 7 • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate without the cutting attachment shield in place.
RULES FOR SAFE OPERA TION 8 KNOW YOUR UNIT Handle Harware Primer Bulb Muffler Air filter/Muffler Cover Fuel Cap Throttle Contr ol Power Head Choke Lever D-handle (705r) J-handle (725r) Click-Link (725.
ASSEMBL Y INSTRUCTIONS 9 INST ALLING AND ADJUSTING THE D-HANDLE - MODEL 705r 1. Push the D-handle down onto the shaft housing so that the handle slants to the powerhead (Fig. 1). The squared bolt hole in the handle is to the right. INST ALLING AND ADJUSTING THE J-HANDLE - MODEL 725r 1.
INST ALLING THE CUTTING A TT ACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed. WARNING: Never operate the trimmer without the cutting attachment shield in place to prevent serious personal injury .
WARNING: Gasoline is extr emely flammable. Ignited V apors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the ar ea. WARNING: Remove fuel cap slowly to avoid injury from fuel spray .
ST ARTING/STOPPING INSTRUCTIONS 12 4. Place the choke lever in the FULL choke position (A) (Fig. 10). 8. If the engine does not start, repeat steps 4 through 7. NOTE: If the engine floods while trying to start, place the choke lever in the RUN position (C) .
2. While firmly holding the add-on, push straight into the Click-Link ® shaft (Fig. 13). NOTE: Aligning the release button with the guide recess will help installation (Fig. 12) . CAUTION: Lock the release button in the primary hole and securely tighten the knob before operating this unit.
Each time the head is bumped, about 1 in. (25.4 mm.) of trimming line is released. A blade in the cutting attachment shield will cut the line to the proper length if excess line is r eleased. For best results, tap the Bump Head ™ on bar e ground or har d soil.
OPERA TING INSTRUCTIONS 15 TIPS FOR BEST TRIMMING RESUL TS • The correct angle for the cutting attachment is parallel to the ground. • Do not force the cutting attachment. Allow the tip of the line to do the cutting (especially along walls). Cutting with more than the tip will reduce cutting ef ficiency and may overload the motor .
MAINTENANCE AND REP AIR INSTRUCTIONS 16 7. Repeat procedur es 4-6 with the second piece of line. 8. Hold the outer spool. Wind the inner reel counterclockwise until appr oximately four (4) inches (102 mm.) of line remain (Fig. 23). NOTE: Do not wind the inner reel befor e installing the second piece of line.
MAINTENANCE AND REP AIR INSTRUCTIONS 17 Bump Knob Foam Seal Spring Inner Reel Installing a Prewound Inner r eel 1. Remove the bump knob, spring, and foam seal by turning the Bump Knob counterclockwise (Fig. 25). 9. If winding the line becomes difficult or the line jams, pull the ends of the line from the spool.
MAINTENANCE AND REP AIR INSTRUCTIONS 18 AIR FIL TER/MUFFLER COVER REMOV AL AND INST ALLA TION Removing the Air Filter/Muffler Cover WARNING: T o avoid serious personal injury , always tur n your trimmer off and allow it to cool before you clean or do any maintenance on it.
MAINTENANCE AND REP AIR INSTRUCTIONS 19 6. Replace the air filter in the air filter/muffler cover (Fig. 31). 7. Reinstall the air filter/muffler cover , and screws (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 20 CARBURETOR ADJUSTMENT The factory carefully calibrated the carbur etor . It seldom needs further adjustment. Careless adjustments can seriously damage your unit. An authorized service dealer must make carburetor adjustments.
MAINTENANCE AND REP AIR INSTRUCTIONS 21 REPLACING THE SP ARK PLUG Use a Champion RDJ7Y spark plug (or equivalent). The correct air gap is 0.020 in. (0.5 mm.) . Remove the plug after every 50 hours of operation and check its condition. 1. Stop the engine and allow it to cool.
CLEANING AND STORAGE 22 TRANSPORTING • Allow the engine to cool before transporting. • Secure the unit while transporting. • Tighten fuel cap before transporting. CLEANING WARNING: T o avoid serious personal injury , always tur n your trimmer off and allow it to cool before you clean or do any maintenance on it.
Engine will not start Engine will not idle Low idle speed Engine will not accelerate Engine lacks power or stalls when cutting Cutting head will not advance line Cutting line advances uncontrollably I.
SPECIFICA TIONS 24 ENGINE Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled , 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 The California Air Resources Board and Ryobi Outdoor Products (ROP), are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
R YOBI OUTDOOR PRODUCTS warrants each new R YOBI Product for two (2) years according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of original retail purchase.
デバイスRyobi 705rの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ryobi 705rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi 705rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi 705rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi 705rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi 705rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi 705rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi 705rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi 705rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。