Ryobiメーカー725rEの使用説明書/サービス説明書
ページ先へ移動 of 28
T r i m m e r P l u s ® 725rE 2-Cycle Gas T rimmer / Edger OPERA TOR’S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA www.
INTRODUCTION T ABLE OF CONTENTS 2 THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-to-under- stand operating instructions.
CALIFORNIA EMISSION REGULA TIONS 3 SP ARK ARRESTOR W ARNING! RULES FOR SAFE OPERA TION NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington.
RULES FOR SAFE OPERA TION 4 READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.
RULES FOR SAFE OPERA TION 5 • Do not touch the engine or muffler. These parts get extremely hot from operation. When turned off they remain hot for a short time. • Do not operate the engine faster than the speed needed to cut, trim or edge. Do not run the engine at high speed when not cutting.
SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING • HOT SURF ACE WARNING Do not touch a hot muffler or cylinder . Y ou may get burned. These parts get extremely hot from operation. When turned off they r emain hot for a short time. • SHARP BLADE WARNING: Ther e is a sharp blade on the cutting attachment shield.
RULES FOR SAFE OPERA TION 8 KNOW YOUR UNIT APPLICA TIONS As a trimmer; • Cutting grass and light weeds. • Decorative trimming around trees, fences, etc.
ASSEMBL Y INSTRUCTIONS 9 7. Tighten the clamp screws evenly, until the J-handle is secure. 6. While holding the unit in the operating position (Fig. 3), position the J-handle to the location that provides you the best grip. Decal INST ALLING AND ADJUSTING THE J-HANDLE 1.
OIL AND FUEL INFORMA TION 10 WARNING: Gasoline is extr emely flammable. Ignited V apors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the ar ea.
11 ST ARTING/STOPPING INSTRUCTIONS 4. Place the choke lever in the FULL choke position ( A ) (Fig. 5). 8. If the engine does not start, repeat steps 4 through 7. NOTE: If the engine floods while trying to start, place the choke lever in the RUN position ( C ) (Fig.
OPERA TING INSTRUCTIONS 12 2. While firmly holding the add-on, push it straight into the Click-Link ® coupler (Fig. 8). NOTE: Aligning the release button with the guide recess will help installation (Fig. 8). 3. Turn the knob clockwise to tighten (Fig.
13 OPERA TING INSTRUCTIONS Fig. 10 Fig. 11 Each time the head is bumped, about 1 inch (25.4 mm.) of trimming line is released. A blade in the cutting attachment shield will cut the line to the proper length if excess line is released. For best results, tap the Bump Head ™ on bare ground or hard soil.
OPERA TING INSTRUCTIONS 14 DECORA TIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30 ° angle to the ground (Fig.
15 OPERA TING INSTRUCTIONS FREQUENCY MAINTENANCE REQUIRED REFER TO: Before Starting Engine Fill fuel tank with correct oil and fuel mixture. Page 10 Every 10 Hours Clean and re-oil air filter. Page 20 Every 50 Hours Check spark plug condition and gap.
16 MAINTENANCE AND REP AIR INSTRUCTIONS Line Locking Hole Trimming Line Line Loading Hole Eyelet 5. Insert the line into the locking hole (Fig. 18). Do not push the line more than 1/2 inch (12.7 mm.) into the line locking hole. When inserted correctly the line will form a small loop (Fig.
17 MAINTENANCE AND REP AIR INSTRUCTIONS Bump Knob Foam Seal Spring Inner Reel Installing a Prewound Inner reel 1. Turn the Bump Knob counterclockwise and remove the bump knob, spring, and foam seal (Fig. 22). 9. If winding the line becomes difficult or the line jams, pull the ends of the line from the spool (Fig.
18 MAINTENANCE AND REP AIR INSTRUCTIONS 2. Pull out the bump knob, spring, and foam seal (Fig. 22). 3. Pull the inner reel with existing line from the outer spool (Fig. 22). 4. Remove any existing line from the inner reel before cleaning. Remove any debris or grass from the knob, spring, inner reel, and foam seal.
3. Install the new blade, blade retainer, and nut (Fig. 29). EDGER BLADE REPLACEMENT WARNING: T o avoid serious personal injury , always wear gloves while handling, removing or installing the blade. WARNING: The gear housing gets hot after long periods of use.
MAINTENANCE AND REP AIR INSTRUCTIONS 20 Fig. 32 Fig. 33 Fig. 34 4. Apply enough clean SAE 30 oil to lightly coat the filter (Fig. 34). Air Filter 3. Wash the filter in detergent and water (Fig. 33). Rinse the filter thoroughly. Squeeze out excess water.
6. Replace the air filter in the air filter/muffler cover (Fig. 32). NOTE: Operating the unit without the air filter and air filter/muffler cover assembly, will VOID the warranty. Reinstalling the Air filter/Muffler Cover 1. Place the air filter/muffler cover over the back of the carburetor and muffler.
MAINTENANCE AND REP AIR INSTRUCTIONS 22 REPLACING THE SP ARK PLUG Use a Champion RDJ7Y spark plug (or equivalent). The correct air gap is 0.020 inch (0.5 mm.) . Remove the plug after every 50 hours of operation and check its condition. 1. Stop the engine and allow it to cool.
CLEANING AND STORAGE 23 TRANSPORTING • Allow the engine to cool before transporting. • Secure the unit while transporting. • Drain fuel from unit. • Tighten fuel cap before transporting. CLEANING WARNING: T o avoid serious personal injury , always turn your trimmer off and allow it to cool before you clean or do any maintenance on it.
TROUBLESHOOTING 24 CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inn.
SPECIFICA TIONS 25 Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES 26.
27 The California Air Resources Board and Ryobi Outdoor Products (ROP), are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE TWO (2) YEAR WARRANTY PERIOD OR NINETY (90) DAYS FOR PRODUCTS USED FOR ANY COMMERCIAL PURPOSE. ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES INCLUDING .
デバイスRyobi 725rEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi 725rEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi 725rEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi 725rEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi 725rEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi 725rEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi 725rEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi 725rEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi 725rEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
