RyobiメーカーC2600の使用説明書/サービス説明書
ページ先へ移動 of 19
SA VE THIS MANUAL FOR FUTURE REFERENCE OPERA TOR'S MANUAL 14 in. (356 mm) Abrasive Cut-Off Machine – Model C2600 THANK YOU FOR BUYING A RYOBI ABRASIVE CUT -OFF MACHINE. Y our new cut-off machine has been engineered and manufactured to Ryobi's high standards for dependability , ease of operation, and operator safety .
Page 2 TABLE OF CONTENTS ■ T able Of Contents .............................................................................................................. ......................... 2 ■ Rules For Safe Operation ...................................
Page 3 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 4 RULES FOR SAFE OPERA TION Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your cut-off machine works.
Page 5 RULES FOR SAFE OPERA TION W ARNING: Wheel coasts after turn of f. ■ NEVER USE IN AN EXPLOSIVE A TMOSPHERE. Normal sparking of the motor or sparking from cutting metal could ignite fumes. ■ INSPECT TOOL CORDS PERIODICALL Y and if damaged, have repaired at your nearest Ryobi Authorized Service Center .
Page 6 EXTENSION CORDS Use only 3-wire extension cords that have 3-prong ground- ing plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw.
Page 7 Y our abrasive cut-off machine has been shipped completely assembled. ■ Remove all loose parts from the carton. ■ Remove the packing materials from around your machine. ■ Carefully lift the cut-of f machine from the carton and place it on a level work surface.
Page 8 FEA TURES KNOW YOUR ABRASIVE CUT-OFF MACHINE See Figures 2 and 3. Before attempting to use your machine, familiarize yourself with all operating features and safety requirements. W ARNING: Do not allow familiarity with your machine to make you careless.
Page 9 0 15 30 Fig. 3 LOWER WHEEL GUARD UPPER WHEEL GUARD MACHINE ARM LOCK-ON BUTTON RUBBER FEET CARRYING HANDLE MACHINE BASE SWITCH TRIGGER VISE CLAMP POWER CORD QUICK LOCK- RELEASE LEVER VISE CRANK HANDLE 8 mm HEX KEY WRENCH STORAGE ADJUSTABLE FLIP FENCE ASSEMBLY Fig.
Page 10 ADJUSTMENTS W ARNING: T o prevent accidental starting that could cause possible serious personal injury , assemble all parts to your cut-of f machine before connecting it to power supply . Machine should never be connected to power supply when you are assembling parts, making adjustments, installing or removing wheels, or when not in use.
Page 11 0 15 30 45 15 45 0 ADJUSTMENTS Fig. 6 ADJUSTABLE FLIP FENCE See Figure 6. The adjustable flip fence is located at the rear of your cut-off machine. As mentioned previously, it is used along with the vise clamp to provide a clamp for holding your workpiece securely when making cuts.
Page 12 ADJUSTMENTS Fig. 9 QUICK LOCK-RELEASE LEVER See Figures 9 and 10. The quick lock-release lever engages the vise clamp to be used along with the fence assembly to provide a vise for securing the workpiece to be cut. It also allows you to open and close the vise quickly without repetitive turning of the vise crank handle.
Page 13 0 15 ADJUSTMENTS Fig. 11 DEPTH STOP The depth stop limits the wheel's downward travel. It allows the wheel to go below the machine base enough to maintain full cutting capacities. The adjustable depth stop is a nylok bolt threaded into the base of the machine at the rear .
Page 14 15 45 0 MATERIAL TO BE CUT POWER SUPPL Y Before operating your cut-off machine, check your power supply and make sure it meets the requirements listed on the tool’s data plate. A substantial voltage drop will cause a loss of power and machine overheating.
Page 15 15 45 0 OPERA TION CUT -OFF See Figures 14 and 15. A cut-of f is made by cutting across the width of the workpiece. A straight crosscut is made with the adjustable flip fence set at the zero degree position. Angled cut-offs are made with the adjustable flip fence set at some angle other than zero.
Page 16 MOUNTING HOLES Your cut-off machine should be permanently mounted to a firm supporting surface such as workbench. The four bolt holes that secure the feet on the bottom of the base can be used for this purpose. Using a 6 mm hex key, remove bolts, washers, and feet from bottom of cut-off machine.
Page 17 Fig. 17 W ARNING: T o ensure safety and reliability , all repairs — with the exception of the externally accessible brushes — should be performed by a Ryobi Authorized Service Center . BRUSH REPLACEMENT See Figure 17. Your cut-off machine has externally accessible brush assemblies that should be periodically checked for wear.
Page 18 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Motor does not reach full speed or 1. V oltage from power source is low . 1. Request a voltage check from the power . power company . 2. Circuit is overloaded. 2. T est on a different circuit or without anything else on circuit.
972000-683 6-00 RYOBI AMERICA CORPORATION 1424 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 R YOBI CANADA INC.
デバイスRyobi C2600の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ryobi C2600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi C2600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi C2600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi C2600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi C2600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi C2600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi C2600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi C2600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。