RyobiメーカーCSB1308の使用説明書/サービス説明書
ページ先へ移動 of 20
OPERA T OR'S MANUAL 7-1/4 in. (184 mm) Circular Saw Model CSB1308 DOUBLE INSULA TED THANK YOU FOR BUYING A RYOBI CIRCULAR SAW. Your new circular saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety.
Page 2 TABLE OF CONTENTS W ARNING: Read and understand all instructions. Failure to follow all instructions listed below can result in electric shock, fire, and/or serious personal injury . SA VE THESE INSTRUCTIONS W ork Area ■ Keep your work area clean and well lit .
Page 3 GENERAL SAFETY RULES Personal Safety (continued) ■ Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury . ■ Do not overreach. Keep proper footing and balance at all times.
Page 4 SPECIFIC SAFETY RULES Specific Safety Rules for Circular Saws (continued) ■ Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path.
Page 5 Additional Rules for Safe Operation ■ Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or serious injury.
Page 6 45 0 KNOW YOUR CIRCULAR SAW See Figure 1. Before attempting to use your saw, familiarize yourself with all operating features and safety requirements. W ARNING: If any parts are missing, do not operate your tool until the missing parts are replaced.
Page 7 ASSEMBL Y ■ Carefully remove the saw and accessories from box. Make sure all items listed in the Packing List are included. ■ Do not discard the packing material until you have carefully inspected and satisfactorily operated saw. ■ Examine all parts and accessories to make sure that no breakage has occurred during shipping.
Page 8 ASSEMBL Y ■ Wipe a drop of oil onto inner flange bushing and outer blade washer ("D" washer) where they contact blade. W ARNING: If inner flange bushing has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.
Page 9 RIGHT OPERA TION Fig. 6 WRONG CORRECT BLADE DEPTH SETTING = BLADE EXPOSED 1/4 in. OR LESS ON UNDERSIDE OF WORKPIECE Fig. 5 W ARNING: Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc.
Page 10 RIGHT WRONG DEPTH OF CUT ADJUSTMENT Always keep correct blade depth setting. The correct blade depth setting for all cuts should not exceed 1/4 in. below the material to be cut. More blade depth will increase the chance of kickback and cause the cut to be rough.
Page 11 RIGHT OPERA TION NEVER PLACE YOUR SAW ON THAT PART OF THE WORK THAT WILL FALL OFF WHEN THE CUT IS MADE. See Figure 11. Keep the cord away from cutting area. ALWAYS place the cord to prevent it from hanging up on the work while making a cut. Utilize the cord clip to help prevent cord problems.
Page 12 45 0 ALTERNATE METHOD FOR RIP CUTTING 4 5 4 5 0 45 0 OPERA TION TO CROSS CUT OR RIP CUT See Figure 14. When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base (as shown in Figure 14) and view the blade through the viewing window.
Page 13 0 1 5 3 0 45 51.5 OPERA TION TO BEVEL CUT See Figure 17 and 18. The angle of cut of your saw may be adjusted to any desired setting between zero and 51.5 degrees. There is a window in the saw base to help you line up the blade with the line of cut.
Page 14 5 1 . 5 4 5 3 0 45 0 1 5 OPERA TION LENGTH OF CUT SCALE Fig. 19 BEVEL ADJUSTMENT KNOB ADJUSTMENT SCREW POSITIVE 0˚ BEVEL STOP HEX NUT COMBINATION SQUARE SAW BLADE Fig.
Page 15 TO POCKET CUT See Figure 21. W ARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of control of your saw possibly causing serious injury.
Page 16 MAINTENANCE DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation.
Page 17 NOTES.
R YOBI CIRCULAR SA W – MODEL NUMBER CSB1308 Page 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 28 27 15 26 17 29 41 33 (Optional) 31 32 30 34 35 32 31 36 37 38 39 40 (Optional) 4.
Page 19 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CIRCULAR SAW or when ordering repair parts. P ARTS LIST Key Part No. Number Description Quan. Key Part No.
972000-831 OPERA T OR'S MANUAL 7-1/4 in. (184 mm) Circular Saw Model CSB1308 DOUBLE INSULA TED • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center.
デバイスRyobi CSB1308の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ryobi CSB1308をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi CSB1308の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi CSB1308の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi CSB1308で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi CSB1308を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi CSB1308の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi CSB1308に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi CSB1308デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。