RyobiメーカーPLT3043A, RY70101Aの使用説明書/サービス説明書
ページ先へ移動 of 18
OPERA T OR’S MANUAL T rimmer PL T3043A R Y70101 Y our ne w trimmer has been engineered and manufactured to Ry obi’s high standard f or dependability , ease of operation and operator saf ety . Properly cared for , it will giv e you years of rugged, troub le-free perf or mance.
2 T ABLE OF CONTENTS SAFETY W ARNING: Do not attempt to operate this trimmer until you have read thoroughly and understand completely all instructions, safety rules etc contained in this manual. Failure to comply may result in accidents involving fire, electric shock or serious personal injury.
3 SAFETY Q Q Q Q Q Secure long hair so it is above shoulder level to prevent entanglement in any moving parts. Q Q Q Q Q Keep all bystanders, children and pets at least 15 m (50 ft) away. Q Q Q Q Q Do not operate this unit when you are tired, ill or under the influence of alcohol, drugs or medication.
4 SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates danger, warning or caution.
5 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
6 FEA TURES Fig. 1 THROTTLE TRIGGER SILENCER GUARD STARTER GRIP CHOKE LEVER THROTTLE CONTROL AND REAR HANDLE FRONT HANDLE DRIVE SHAFT HOUSING STRING HEAD GRASS DEFLECTOR IGNITION SWITCH UNP ACKING INSTRUCTIONS Q Q Q Q Q Carefully remove the product from the carton.
7 ASSEMBL Y SILENCER GUARD ASSEMBLY See Figure 4. 1. Remove silencer guard and two screws from the owner’s kit. 2. Attach the silencer guard to the rear housing. NOTE: Make sure the bent end of the silencer guard fits securely into the opening of the rear housing.
8 FILLING THE TANK 1. Clean surface around fuel cap to prevent contamination. 2. Loosen fuel cap slowly to release pressure and to keep fuel from escaping around the cap. 3. Carefully pour fuel mixture into the tank. Avoid spillage. 4. Prior to replacing the fuel cap, clean and inspect the gasket.
9 OPERA TION ADVANCING THE STRING ADVANCING STRING USING THE EZ LINE™ TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string.
10 TO START A COLD ENGINE: 1. Lay trimmer on a flat, bare surface. Move switch to “I” (RUN) position. NOTE: Unit is equipped with a positive on-off switch. Make sure switch is in the “I” (RUN) position before starting the unit. 2. Push primer bulb 8 to 10 times .
11 MAINTENANCE W ARNING: Use only original manufacturer’s replacement parts, accessories and attachments. Failure to do so can cause possible injury, poor performance and may void your warranty. EYELETS SPRING SLOTS STRING HEAD DRIVE SHAFT Fig. 10 Fig.
12 STRING REPLACEMENT See Figures 12, 13, 14 and 15. 1. Stop the engine, disconnect the sparking plug wire. Hold the string head and unscrew the spool retainer. Turn anticlockwise. 2. Remove the spool from the string head. NOTE: Keep the spring attached to the spool.
13 The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine perfor- mance. If performance improves when the fuel cap is loosened, the check valve may be faulty or the filter clogged. Replace fuel cap if required.
14 PROBLEM PROBLEM PROBLEM PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE SOLUTION SOLUTION SOLUTION SOLUTION SOLUTION IF THESE SOLUTIONS DO NOT SOL VE THE PROBLEM, CONT ACT YOUR AUTHORISED SER VICE DEALER. TROUBLESHOOTING 1.
15 1 “H” HIGH NEEDLE PROBLEM PROBLEM PROBLEM PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE SOLUTION SOLUTION SOLUTION SOLUTION SOLUTION IF THESE SOLUTIONS DO NOT SOL VE THE PROBLEM, CONT ACT YOUR AUTHORISED SER VICE DEALER.
16 SOUND POWER/PRESSURE AND HANDLE VIBRATION CHART FOR TRIMMERS / BRUSHCUTTERS Information on Noise Emission per European Machine Safety Directive 98/37/EC. The individual equipment listed was operated in a manner consistent with normal working conditions.
17 NOTES.
983000-200 2-03 OPERA T OR’S MANUAL T rimmer PL T3043A R Y70101 Ryobi T echnologies GmbH Itterpark 7 D-40724 Hilden Germany T el.: +49 (0)2103 / 29 58 0 F ax : +49 (0)2103 / 29 58 29 info@ryobi-rtg.
デバイスRyobi PLT3043A, RY70101Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi PLT3043A, RY70101Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi PLT3043A, RY70101Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi PLT3043A, RY70101Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi PLT3043A, RY70101Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi PLT3043A, RY70101Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi PLT3043A, RY70101Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi PLT3043A, RY70101Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi PLT3043A, RY70101Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
