AudiovoxメーカーPrestige APS-905の使用説明書/サービス説明書
ページ先へ移動 of 20
128-7410 1 of 20 Page 1 Kit Contents (1) Control Module (1) 5 Button One Way Flashlight Transmitter (1) 5 Button Two Way Dot Matrix Transceiver (1) On Glass Mount Superheterodyne Transceiver (1) Multi.
128-7410 2 of 20 Page 2 SELECT ABLE FEA TURES The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text.
128-7410 3 of 20 Page 3 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, tu.
128-7410 4 of 20 Page 4 T o exit program mode, turn ignition of f, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: T o program these selectable .
128-7410 5 of 20 Page 5 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chir.
128-7410 6 of 20 Page 6 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission Vehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
128-7410 7 of 20 Page 7 THE TRANSCEIVER/ANTENNA ASSEMBL Y : The Superheterodyne T ransceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.
128-7410 8 of 20 Page 8 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch.
128-7410 9 of 20 Page 9 on + 12 volt source which will supply + 12 volt power to the additional ignition output, (Pink), wire. PINK Wire: Additional Ignition Output This wire can be used as an additional + 12 Volt ignition output supplied by the Red/Black wire.
128-7410 10 of 20 Page 10 If the vehicle has a factory installed hood pin switch and that switch provides + 12 Volts to an under hood light, the Brown wire can be connected to the existing pin switch.
128-7410 11 of 20 Page 11 LIGHT BLUE Wire: Ground Output While Running. This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off.
128-7410 12 of 20 Page 12 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.
128-7410 13 of 20 Page 13 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA.
128-7410 14 of 20 Page 14 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface.
128-7410 15 of 20 Page 15 3. Diagnostics: 1. Enter Bank 3 and turn on selectable feature # 9 as described on the front pages of this manual. 2. Press and hold the program push-button switch on, then turn the ignition key to the "ON" position.
128-7410 16 of 20 Page 16 MANUAL SHUT DOWN / ENABLE CIRCUIT : The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the Remote Start Unit regardless of the RF transmitter operation. T o test the integrity of the manual shut down / enable circuit: 1.
128-7410 17 of 20 Page 17 addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM input circuit. T o connect the Audiovox remote start u nit to the GM Park / Neutral ECM input: 1.
128-7410 18 of 20 Page 18 F . Connect terminal #86 of the relay to a fused +12 volt constant battery source. G. Connect terminal #87 of the relay to the Chime Module side of the previously cut wire in step D. H. Connect terminal #85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B.
128-7410 19 of 20 Page 19 AFTER THE CONNECTION OF THE NEUTRAL ST ART SAFETY WIRE AS INDICA TED IN ANY OF THE PREVIOUS AL TERNA TE CONFIGURA TIONS, THIS CIRCUIT MUST BE TESTED FOR OPERA TION. Retest by following the steps outlined in the NEUTRAL ST ART SAFETY TEST shown in this manual.
128-7410 20 of 20 Page 20 © 2005 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7410.
デバイスAudiovox Prestige APS-905の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Audiovox Prestige APS-905をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox Prestige APS-905の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox Prestige APS-905の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox Prestige APS-905で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox Prestige APS-905を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox Prestige APS-905の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox Prestige APS-905に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox Prestige APS-905デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
