AudiovoxメーカーPRO 9171FTの使用説明書/サービス説明書
ページ先へ移動 of 12
3 Channel Remote Car Starter Installation Instructions For installation in vehicles with 12 volt negative ground circuits, gasoline engines, with automatic transmission only! Model PRO 9171FT Installa.
The PRO-9171FT is for Automatic Transmission vehicles only! Although it is a sophisticated system, with multiple built-in safety features, it must not be installed into vehicles with manual transmissions. Doing this can cause serious personal injury and property damage.
LIGHT GREEN Wire : Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show +12 Volts when the ignition key is turned to the “ RUN or ON “ position, and in some cases, the “ START or CRANK “ position.
4 This wire provides a 500 mA + 12 Volt transistorized output when the ignition key is turned to the “ON” position, and 0 Volts when the ignition key is “OFF” and when the vehicle is running under the control of the remote starter. This wire should be connected to the ignition input of the alarm system.
5 DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the tach rate while the engine is running under power supplied by the Remote Starter. This wire will be routed through the fire wall into the engine compartment. It is necessary to use an existing grommet when passing wires through the fire wall to prevent short circuiting.
To program these selectable features: 1. Start with the programming switch in the OFF position. 2. Turn the ignition key to the ON position. 3. Flip the program switch ON - OFF - ON - OFF - ON - then OFF. 4. Immediately turn the ignition key OFF, then back to ON.
NEUTRAL ST ART SAFETY TEST : The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any position other than Park, or Neutral. When installing a Remote S tart Device, it is imperative that the Y ellow Starter wire be connected to the ignition switch side of the Neutral Start Switch.
KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S t art Switch from starting in gear .
T o connect to the key in sensor as shown in method 1: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .
10 NOTE: A second 4002 series diode may be required to maintain t he integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit.
12 PIN CONNECTOR WIRING THE 12 PIN INPUT / OUTPUT HARNESS CONTROL SWITCH TO ALARM'S IGNITION INPUT- (YELLOW WIRE OF AUDIOVOX ALARMS) LIGHT BLUE WHITE WHITE POSITIVE INHIBIT 1 NEGATIVE INHIBIT 2 T.
© 1998 Audiovox Corporation, Hauppauge, NY 11788 128-5404.
デバイスAudiovox PRO 9171FTの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Audiovox PRO 9171FTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox PRO 9171FTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox PRO 9171FTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox PRO 9171FTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox PRO 9171FTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox PRO 9171FTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox PRO 9171FTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox PRO 9171FTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
