Sangean ElectronicsメーカーDT-300Vの使用説明書/サービス説明書
ページ先へ移動 of 17
.
1 5 3 6 7 8 9 11 12 13 14 2 4 10 2.
3 Location Of Controls W elcome to SANGEAN W orld of Listening. To ensure proper operation please familianrize yourself with These instructions before using your new receiver.
1 2 3 4 5 6 7 8 9 A B C D E F I J K L 4 G H.
5 Display Icons Band Selected/ PM---------------------------------------------------------- Timer / (Alarm)-------------------------------------------------------------- FM Stereo lndicator-----------.
Battery Installation The battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment insert 2 AAA(UM-4) batteries into the compartment.Make sure that batteries are positioned in accordance with the diagram located below batteries in battery compartment.
7 3 8 13 14 8 8 Setting Time When batteries are installed for the first time the LCD display time digit will flash indicating that the time needs to be set. The clock can be set with the power off but the lockswitch must be off. T o set time press Time Set Button for more then 2 seconds until hour digit flashes.
8 13 14 14 9 9 LCD will return to real time and Standby Set icon will appear in display . A buzzer will sound when set time is reached and will continue for at least 3 mimutes or until it is stopped by pressing the Power On/Off Button. Short T erm Alarm Set This receiver is equipped with a short term 1-180minute timer.
9 RADIO OPERA TION Antenna/Earphone Use The earphone cord acts as an antenna during reception of FM/TV/Weather Band(DT -300/300V/300VW)channels and should be extended as much as possible to improve sensitivity . Insert the earphone into the earphone jack for earphone operation .
V olume Control The volume may be adjusted by using the V olume Control Adjustment T uning the Radio Band Frequency Antenna AM 520-1710kHz/ Internal-Rotate radio for best 522-1629kHz reception FM 87.5-108MHz External-Make sure earphone or pig tail antenna is inserted into earphone jack.
WX CH.0-9 External-Make sure earphone or pigtail antenna is inserted into Earphone jack A.Scan T uning Turn on the radio by pressing On/Of f Button . Select the desired band by pressing Band Selection Button Press and hold the Tuning Control Button or for more than 1/2 second .
12 13 14 5 11 8 11 13 14 until the desired station is reached or pressing and holding the T uning Control or until the station is reached. C. Setting Presets Manually Turn on receiver by pressing On/Of f Button .Select desired band by pressing Band Selector Button .
13 11 11 5 8 12 13 14 station is selected to take its place. When the memory is full for a particular band pressing the Memory Selection Button will cause all the positions to flash. In this case,select the desired position. press the Memory Selection Switch and the original station will be eliminated and the new station will take its place.
5 8 11 12 11 5 8 On/off Button .Select desired band by pressing Band Select or Button . Press Memory Button . Memo will flash in display. Press Select Button for move than 2 seconds until auto/memo appears and flashes in display. press memory Button again.
15 Note: If the Select Cursor points at the frequency the Tuning Control Up/Down Button will continue to change frequency within the band selected. If the Selector Cursor points at the position digits for the memory presets the Tuning Control Up/Down Button and will select the memory presets.
16 9 7 3 3 Mono/Stereo Button Monaural or Stereo headphone reception may be selected durning FM reception by alternately pressing the Mono/Stereo Button The Speaker On/OffSwitch must be in the Off Lock Switch To Prevent accidental changing of any of the radio settings move the Look Switch to the locked position.
Specification T ype: FM- Stereo (Via earphone) AM- Standard (mono) TV Band (Mono Ch,2-13 VHF) DT -300V/VW W eather Band (WX) (Mono Ch. 0-9) DT -300VW Earphone jack: 3.5 mm mini-plug 16 or 32 ohm impedance (Stereo) Output Power: 50 mW (10 THD) via built-in speaker Speaker: 1.
デバイスSangean Electronics DT-300Vの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sangean Electronics DT-300Vをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSangean Electronics DT-300Vの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sangean Electronics DT-300Vの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sangean Electronics DT-300Vで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sangean Electronics DT-300Vを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSangean Electronics DT-300Vの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sangean Electronics DT-300Vに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSangean Electronics DT-300Vデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。