SangeanメーカーHDT-1の使用説明書/サービス説明書
ページ先へ移動 of 23
381R20S-A HD Radio TM Component T uner User Manual 20070425_HDT-1&HDT-1X_381R20S-A_«Ê-±.p65 2007/4/27, ¤U¤È 03:58 1.
HD Ra dio™ T echnology M anufa ctured Under Licen se From iBiquity Digital Corporation. iBiquity Digital a nd the HD Ra dio a nd HD logos are registered trade marks of iBiquity Digital Corporation. HD Ra dio TM is a trade mark of iBiquity Digital Corporation.
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this a pparatus near water . 6. Clea n only with dry cloth. 7. Do not block any ventilation openings.
3 Main Unit Controls (Front & Remote Control) Unit Button 1 2 3 4 5 6 7 8 9 10 11 12 Remote Button A C N/A N/A G H I D B E F N/A Action/Combination Turns unit on/off 10 Digit Keypad FREQ Preset Clock Set Remote Sensor LCD Display Tuning Adva nced Menu Options Seek Tuning HD Seek Tuning BAND INFO 2 sec.
4 20070425_HDT-1&HDT-1X_381R20S-A.p65 2007/4/30, ¤U¤È 01:43 7.
5 Main Unit Controls (Rear) 13. 14. 15. 16. External FM a ntenna socket External AM loop antenna socket Line Out socket SPDIF Optical Connection (Optional on HDT -1X) AC power cord socket 17.
6 Acce ssorie s Detacha ble power Cord x 1 FM Dipole Antenna x 1 AM Loop a ntenna x 1 20070425_HDT-1&HDT-1X_381R20S-A.p65 2007/4/30, ¤U¤È 01:44 9.
7 RCA type audio cable x 1 Remote control unit x 1 Instruction ma nual x 1 Warra nty cardSeek Function T o seek to another cle ar station, use the SEEK toggle button .
8 Getting started Step 1. Inspect pa ckage to insure that all parts & acce ssorie s are included. Step 2. Find a proper location for your new HDT -1/HDT -1X HD Ra dio Tuner following the guidelines on table 1.1. Step 3. Connect the included or other external FM a ntenn a to Figure 2, #13.
9 Navigating the Display There are ma ny display functions . This will help you understa nd what the display is telling you, making navigation a nd setup ea sier.
10 Setting up a nd Progra mming your HDT -1/HDT -1X Setting the clock Clock setting can be done when the tuner is in Standby (power off) 1. Press and hold “INFO” button for approx. 2 seconds until display flashes “clock set “to enter Clock Set mode.
11 Radio Controls T o turn the radio on, press the Sta ndby button. Pressing the Standby button again will put the unit into standby . In sta ndby , the tuner will display the time, dim the ba cklight and sta ndby LED will be on. Selecting the ra dio ba nd Press the BAND button to select the a ppropriate ba nd .
12 Ma nual T uning Press the TUNING rocker switch UP or DOW N to tune up or down to select a radio station. Tuning step per press for AM band is 10 kHz a nd 100 kHz for FM ba nd. Direct T uning By using numbered key pad, you ca n directly tune to a radio station.
13 Rece iving HD radio station s When the radio is tuned to a station broadca sting HD radio signal, the LCD will display a blinking “HD “logo. Once the tuner a cquires the HD ra dio signal, the “HD” logo will stay on and a Signal Strength indication will a ppear in the top right hand corner .
14 Seek Function T o seek to a nother clear station, use the SEEK toggle button. Press a nd relea se the SEEK UP or DOW N will go to the next availa ble station with good signal.
15 Recall preset stations T o recall preset stations, sele ct required ba nd by pressing BAND selection button. Press PRESET button to enter PRESET recall mode. Display will show “GO TO PRESET”. Then followed by using one of the following methods to recall the stations.
16 Advanced Information Long press INFO button for 2 se conds to enter Adva nced Inf ormation. Press a nd release INFO button will cycle through inf ormation of RESET , LCD Contra st Adjust, Ba ckligh.
17 Advanced Menu Option s Menu Option Ba cklight Mono/Stereo Mode Analog Mode (HD OFF) Split Audio Mode Bit Error Rate Carrier to Noise Ratio Fuse Bit Check Tra nsmission Mode Station ID Software V er.
18 T roubleshooting Issue Power Won’t Turn On Remote Doesn’t Work I don’t hear a ny audio I only hear audio in one spea ker I only hear static Poor audio quality Possible Solutions Check AC powe.
19 Poor audio quality (Cont.) HD Sign al Keeps Fading in a nd Out Sta nge sound when radio is of f Antenna not correctly installed or oriented Radio station is broa dca sting poor signal Antenna not c.
20 Specifications Power: Mains: AC 120 V olts 60 Hz only, 10 W att maximum Battery ( remote control ): 3.0V CR 2025 Frequency coverage: FM 87.50 - 108.10 MHz AM 520 - 1710 kHz HD FM 87.50 - 108.10 MHz HD AM 520 - 1710 kHz Antenna System: FM - D ipole type ( supplied ) AM - Loop type ( supplied ) Dimension ( W x H x D ): 430x70x256 mm W eight: 2.
21 HDT -1/HDT-1X Brief User Interfa ce: UI KEY function NO 1 2 3 4 5 Button sta ndby Band Info Info Info Action short short short long 2s (T o use info key to jump next status) short(T o use number ke.
22 6 7 8 9 10 Preset Tune Seek HD Seek Freq 1.T o press preset button then to press number button finish setting 2.T o press number button long 2s store cha nnel 3.
デバイスSangean Sangean HDT-1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sangean Sangean HDT-1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSangean Sangean HDT-1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sangean Sangean HDT-1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sangean Sangean HDT-1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sangean Sangean HDT-1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSangean Sangean HDT-1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sangean Sangean HDT-1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSangean Sangean HDT-1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。