SanyoメーカーHEC-DR7700Kの使用説明書/サービス説明書
ページ先へ移動 of 16
CONTENTS PAGE Be sure to read this manual thoroughly in order to ensure proper use. In particular, make certain to read the section " I M P O R T A N T S A F E T Y I N S T R U C T I O N S " . Kee p thi s man ual i n a saf e pla ce so that it ca n be f ound e asil y.
2 IMPORTANT SAFETY INSTRUCTIONS 1 All of the following information is important. Be sure to follow the instructions carefully. Wh e n u s i ng a n e l ec t r ic a l ap p li a n ce , ba s i c p r e ca u ti o n s s h ou l d al w a ys b e f o ll o w ed , in c l ud i n g t h e following: Read all instructions before using this appliance.
4 3 Be careful not to spill water over the remote control, sensor controller, seat, or foot rest. Otherwise, electric shock, short circuit or fire may occur. Do not suddenly release your hand, while raising the foot rest. Otherwise, an injury may occur.
6 5 NAME/FUNCTION OF EACH PART Caster Used when moving the chair. Back rest Back pad Arm rest Head cover Seat Remote control Sensor controller Massaging rollers Cord Power plug Grounding pin Cover A Foot rest slide lever Foot rest Cover B Stand Installation screws (3 screws) Check the accessories at first.
8 7 NAME/FUNCTION OF EACH PART REPEAT! display Turns on during Whole Body Sensor Automatic Courses and Automatic Courses. The ring lights up by pressing the REPEAT! button when you want to repeat your desired massage during the course of massaging.
10 9 HOW TO INSTALL THE STAND Installation screws 1 Remove the covers on the outer sides of the arm rests. Insert the flathead screwdriver into the holes under the cover and pull toward you. (4 places) 5 Put the cords of the remote control and sensor controller in the cord hook on the back of the body.
12 11 HOW TO USE PREPARATIONS PRIOR TO USE ① ③ Press the OPERATION ON/OFF button. Select a massaging course. (See page 16-24) ② Adjust the angle of back rest and foot rest with the ZERO-G button, RECLINING button and FOOT REST UP and DOWN button.
14 13 ADJUSTMENT OF CHAIR Before sitting on the massage chair OR (Remote control) (Sensor controller) Raise the back rest, and lower the foot rest by continuously pressing the UP ( ) button. Recline the back rest, and raise the foot rest by continuously pressing the DOWN ( ) button.
16 15 ADJUSTMENT OF CHAIR MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) Ref er to the page 27 and 2 8 re gardi ng t he ma ssagi ng c onten ts o f Who le B ody S enso r Aut omati c Co urses . Cha nge o f co urse duri ng ma ssag ing, or c hange to t he A utoma tic Cours e or the Manu al Co urse, is possi ble.
18 17 MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) 7 Adjust the strength of massage. (See page 18) ③ Massages according to the stiffness. Adjusts the operation and strength of standard massaging according to the measured degree of stiffness. → Massaging operation and the display of remote control.
20 19 MASSAGING (AUTOMATIC COURSES) ① Measure the position of shoulder. ② Starts the massaging of selected course. Check if the position of shoulder is correct.
22 21 MASSAGING (MANUAL COURSES) 7 Adjust the height, width, speed, and strength of the massaging rollers. There are some adjustments which are not possible, depending on the type of massage chosen. (See page 23) Adjusting the height of massaging rollers.
24 23 Several types of desired massage can be selected. It is possible to adjust the movement speed, height position and width of massaging rollers and the strength of massage. (There are some adjustments that are not possible, depending on the kind of massaging.
26 25 AFTER USE 2 Turn off the POWER. 1 Set the back rest and the foot rest to the starting position. Be sure to check that there are no children, pets, or any obstacles around the massager. MAINTENANCE PROCEDURES Perform daily maintenance by wiping with a soft dry cloth.
28 〈 WHOLE BODY SENSOR AUTOMATIC COURSE 〉 〈 AUTOMATIC COURSE 〉 Standard massage in FINE Course WAIST Course NECK/SHOULDER Course Spine stretching Shiatsu (Shoulder) Tapping/Kneading (Shoulder,.
29 TROUBLE-SHOOTING Type of Trouble The operation stops in the middle of massaging in the Whole Body Sensor Automatic Course or Automatic Course Movement of massaging rollers in upward direction, causing operation to stop Check points Countermeasure You feel discomfort during the operation of reclining.
デバイスSanyo HEC-DR7700Kの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo HEC-DR7700Kをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo HEC-DR7700Kの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo HEC-DR7700Kの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo HEC-DR7700Kで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo HEC-DR7700Kを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo HEC-DR7700Kの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo HEC-DR7700Kに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo HEC-DR7700Kデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
