SanyoメーカーPLC-SW10の使用説明書/サービス説明書
ページ先へ移動 of 40
Owner's Man ual PLC-SW10 Multimedia Pr ojector MODEL.
2 Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.
3 SAFETY INSTR UCTIONS All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
4 COMPLIANCES Federal Comm unication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
5 T ABLE OF CONTENTS FEA TURES AND DESIGN 6 BEFORE OPERA TION 14 COMPUTER MODE 22 VIDEO MODE 29 SETTING 32 APPENDIX 34 PREP ARA TION 7 NAME OF EACH PART OF THE PROJECTOR 7 SETTING-UP THE PROJECTOR 8 C.
6 FEA TURES AND DESIGN This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
7 PREP ARA TION NAME OF EA CH P ART OF THE PR OJECT OR These Air Intake Vents should not be blocked. BO TT OM OF THE CABINET B ACK OF THE CABINET POWER CORD CONNECTOR FRONT OF THE CABINET LAMP COVER A.
NO TE ON THE PO WER CORD The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below and the proper AC power cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
9 PREP ARA TION POSITIONING THE PR OJECT OR ● This projector is designed to project on a flat projection surface. ● The projector can be focused from 4.6 ’ (1.4m) ~ 26.3 ’ (8.0m). ● Refer to the figure below to adjust the screen size. ADJUST ABLE FEET Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET.
10 PREP ARA TION When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and cabinet. When this projector is not in use for an extended period, put it into the case (carrying bag) supplied with this projector.
11 CONNECTING THE PR OJECT OR TERMINALS OF THE PR OJECT OR COMPUTER INPUT TERMINAL Terminal : HDB15-PIN Connect the display output terminal of the computer to COMPUTER INPUT terminal of this projector with the VGA Cable (supplied). When connecting the Macintosh computer, the MAC Adapter (not supplied) is required.
12 CONNECTING THE PR OJECT OR CONNECTING T O THE VIDEO EQUIPMENT COMPUTER IN S – VIDEO COMPUTER CONTROL PORT RESET A UDIO IN AV Y – Pb/Cb – Pr/Cr A UDIO OUT VIDEO Video Source (example) Video Ca.
13 CONNECTING THE PR OJECT OR COMPUTER IN S – VIDEO COMPUTER CONTROL PORT RESET AUD IO IN AV Y – Pb/Cb – Pr/Cr AUDIO OUT VIDEO 13" MODE (640 x 480) 16" MODE (832 x 624) 19" MODE (.
14 V OLUME ON-OFF D.ZOOM KEYST ONE VIDEO MENU MUTE P-TIMER NO SHO W FREEZE A UTO IMA GE NORMAL COMPUTER LOCK BEFORE OPERA TION OPERA TION OF THE REMO TE CONTR OL Used to select COMPUTER input source. (P22) Used to select VIDEO source. (P29) Used to execute the item selected or to expand the image in DIGITAL ZOOM mode.
15 BEFORE OPERA TION V OLUME ON-OFF D.ZOOM KEYST ONE VIDEO MENU MUTE P-TIMER NO SHO W FREEZE A UTO IMA GE NORMAL COMPUTER LOCK MUTE BUTTON Used to mute sound.(P21) NO SHOW BUTTON Used to turn the picture into black image. (P21) AUTO IMAGE BUTTON Use to operate AUTO IMAGE function.
16 ON – OFF MENU MODE NORMAL LAMP REPLA CE WARNING TEMP . READ Y LAMP WIDE TELE BEFORE OPERA TION T OP CONTROLS AND INDICA T ORS Used to open or close the MENU operation. (P17, 18) MENU BUTTON MODE BUTTON READY INDICATOR SELECT BUTTON POWER ON – OFF BUTTON NORMAL BUTTON WARNING TEMP.
17 BEFORE OPERA TION HO W T O OPERA TE ON-SCREEN MENU FLO W OF ON-SCREEN MENU Display ON-SCREEN MENU Press MENU button to display the ON-SCREEN MENU (MENU BAR). The red frame is the POINTER. Select the ITEM by pressing SELECT button. The dialog box of the ITEM appears.
18 BEFORE OPERA TION MENU B AR SYSTEM MENU Used to select a computer system. (Refer to P22) IMAGE MENU Used to adjust the computer image. [Fine sync / Total dots / White Balance / Contrast / Brightness / Gamma] (Refer to P26) PC ADJUST MENU Used to adjust the parameters to match with the input signal format.
19 B ASIC OPERA TION TURNING ON THE PR OJECT OR Connect the projector's AC Power Cord into a wall outlet. The LAMP indicator lights RED, and the READY indicator lights GREEN. Press the power ON-OFF button on the Remote Control Unit or on the Top Control to ON.
20 B ASIC OPERA TION ADJUSTING THE IMA GE KEYST ONE ADJUSTMENT 1 Press the KEYSTONE ▲ / ▼ button on the Remote Control Unit or select the Keystone on the SCREEN menu. (Refer to page 28, 30.) The message “ Keystone ” is displayed. 2 Correct the Keystone distortion by pressing the KEYSTONE ▲ / ▼ button or the POINT UP/DOWN button(s).
21 B ASIC OPERA TION Press the VOLUME (+/ – ) button on the Remote Control Unit to adjust the volume. The Volume dialog box appears on the screen for a few seconds.The VOLUME (+) button increases the volume, and the VOLUME ( – ) button decreases the volume.
22 MODE button Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT button. COMPUTER MODE SELECTING COMPUTER MODE MENU OPERA TION When selecting the Computer Mode, the Current Mode display appears.
23 COMPUTER MODE COMP A TIBLE COMPUTER SPECIFICA TIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of Dot Clock. NOTE : Specifications are subject to change without notice.
24 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector.
25 COMPUTER MODE The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total lines Recalls the parameter data that was previously adjusted. Reset Stores the parameters in the memory. Stored Clears the parameter data previously set.
26 COMPUTER MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
27 COMPUTER MODE The Auto Image function is provided to automatically adjust Fine sync, Total dots, and Picture Position for most computers. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE and press the SELECT button.
28 COMPUTER MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button.
29 MODE button VIDEO MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. SELECTING VIDEO MODE DIRECT OPERA TION Select VIDEO mode by pressing the MODE button on the Top Control or the VIDEO button on the Remote Control Unit.
30 VIDEO MODE SELECTING COLOR SYSTEM Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box VIDEO SYSTEM Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
31 VIDEO MODE PICTURE IMA GE ADJUSTMENT Each of the keys operates as follow. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear.
32 SETTING SETTING MENU Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT button. Another dialog box SETTING Menu will appear. Press the POINT DOWN button and a red-arrow icon will appear.
The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp replacement monitor timer by using this function. (Refer to page 36.) Lamp age SELECTING LANGU A GE Press the MENU button and the ON-SCREEN MENU will appear.
34 APPENDIX OPERA TING WIRELESS MOUSE INST ALLA TION The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse operation.
35 APPENDIX CLEANING THE PR OJECTION LENS Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. When the projector is not in use, replace the lens cover.
36 APPENDIX LAMP REPLA CEMENT When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required. Turn off the projector and disconnect the AC plug.
37 APPENDIX TR OUBLESHOO TING Before calling your dealer or service center for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13.
38 This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. APPENDIX W ARNING : High v oltages are used to operate this projector .
● The specifications are subject to change without notice. 39 APPENDIX 0.7 ” TFT Active Matrix type, 3 panels TECHNICAL SPECIFICA TIONS Multi-media Projector 5.51 lbs (2.5 kg) 7.44 ” x 2.93 ” x 11.42 ” (189mm x 74.5mm x 290mm) (not including Adjustable Feet and Lens) 800 x 600 dots 1,440,000 (800 x 600 x 3 panels) PAL, SECAM, NTSC, NTSC4.
Printed in Japan Part No. 610 285 6873 (1AA6P1P2302-- MK6A) SANY O Electric Co., Ltd.
デバイスSanyo PLC-SW10の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo PLC-SW10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo PLC-SW10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo PLC-SW10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo PLC-SW10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo PLC-SW10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo PLC-SW10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo PLC-SW10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo PLC-SW10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
