SanyoメーカーPLC-XU100の使用説明書/サービス説明書
ページ先へ移動 of 66
Owner ’ s Manual Multimedia Pr oject or MODEL PLC-XU1 0 0.
2 F eatures and Design ◆ Compact Design This projector is designed compact in size and weight. It is easy to carry and work anywhere you wish to use. ◆ Compatibility The projector widely accepts various video and computer input signals including; Computers, 6 Color systems (PAL, SECAM, NTSC, NTSC4.
3 T able of Contents Tr ademar ks Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. F eat ur es and Design . . . . . . . . . . . . . . . . . . .2 T able of Contents . . . .
4 To the Owner CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
5 Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
Mo ving the Pr oject or 6 Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent.
7 Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the plane of the screen as shown in the figure below.
Compliance 8 AC Po wer Cord f or the Unit ed Kingdom: This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus .
9 Bot t om Bac k q Zoom Ring w Infrared Remote Receiver e Focus Ring r Projection Lens t Slide Shutter Lever y Top Controls and Indicators u Exhaust Vent i !4 !3 !2 !1 CAUTION Hot air is exhausted from the exhaust vents. Do not put heat-sensitive objects near this side.
10 o S-VIDEO IN Connect the S-VIDEO output signal from video equipment to this jack (p.16). y AUDIO IN Connect the audio output signal from video equipment connected to t or o to this jack. For a mono audio signal (a single audio jack), connect it to the L (MONO) jack (p.
11 Pa rt Names and Functions q w r y u i q LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.54, 60). u WARNING indicator – Lights red when the projector detects an abnormal condition. – Blinks red when the internal temperature of the projector exceeds the operating range (pp.
12 To ensure safe operation, please observe the following precautions : – Do not bend, drop the remote control or expose the remote control to moisture or heat. – For cleaning, use soft dry cloth. Do not apply benzene, thinner, splay or any chemical material.
13 Pa rt Names and Functions 1 2 3 To insure safe operation, please observe the following precautions: ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid.
14 100" 150" 200" 300" 247" 166" 124" 82" 33" 40" A B 32.8’ (10.0 m) 22.0’ (6.7 m) 16.4’ (5.0 m) 10.8’ (3.3 m) Max. Zoom Min. Zoom A : B = 9 : 1 Screen Size (W x H) mm 4 : 3 aspect ratio Zoom (min) 40” Zoom (max) 813 x 610 5.
15 Installation Connecting t o a Comput er Cables used for connection • VGA Cable (Mini D-sub 15 pin)* • Audio Cables (*One cable is supplied; other cables are not supplied with the projector.
16 Installation Connecting t o V ideo Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-VIDEO Cable • Audio Cable (Cables are not supplied with the projector.
17 Installation Connecting t o Component V ideo Equipment Cables used for connection • Audio Cables • Scart-VGA Cable • Component Cable • Component-VGA Cable (Cables are not supplied with the projector.
18 Installation Connecting the A C P ow er Cord NO TE ON THE POWER CORD AC power cord must meet the requirements of the country where you use the projector. Confirm the AC plug type with the chart below and proper AC power cord must be used. If supplied the AC power cord does not match your AC outlet, contact your sales dealer.
19 16 The preparation display will disappear after 30 seconds. (See page 46 for Lamp control status.) Lamp control status Tu r ning On the Project or Connect the projector’s AC power cord into an AC outlet. The POWER indicator lights red. Open the slide shutter by sliding the slide shutter lever.
20 The message will disappear after 4 seconds. TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF. Tu r ning Off the Pr ojector Press the ON/STAND-BY button on the top control or on the remote control, and “Power off?” appears on the screen.
21 Basic Oper ation Menu bar Pointer (red frame ) Menu icon Item data Press the Point 7 8 buttons to adjust the value. SELECT button Pointer (red frame ) Press the Point ed buttons to move the pointer.
22 Menu Bar PC Syst em Menu Used to select computer system. (p.27) Image A djust Menu Used to adjust computer image. [Contrast / Brightness / Color temp. / White balance (R/G/B) / Sharpness / Gamma] (pp.32, 33) Set ting Menu Used to set the projector's operating configurations.
23 Basic Oper ation Rotate the Zoom Ring to zoom in and out. Rotate the Focus Ring to adjust the focus of the image. Zoom Ring Focus Ring 1 2 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Sound Menu icon.
24 Remote Control Remot e Contr ol Oper ation For some frequently used operations, using the remote control is advisable. Just pressing one of the buttons enables you to make the operation, and no need for calling up the On-Screen Menu. COMPUTER /VIDEO button ✔ Note: • See the next page for the other buttons.
25 Basic Oper ation Remote Control D.ZOOM buttons NO SHOW button AUTO PC button ✔ Note: • See the previous page for the other buttons. POINT ed buttons black out ➜ the captured image ➜ normal ➜ • • • • • Press the NO SHOW button on the remote control to black out the image.
26 Choose either Computer 1 or Computer 2 by pressing the COMPUTER 1 button or COMPUTER 2 button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below.
27 The Auto PC Adjustment function operates to adjust the projector. PC System Menu The PC System Menu icon Selected system is displayed. Systems on this dialog box can be selected. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the PC System Menu icon.
28 Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Move the red frame pointer to the Auto PC Adj. item and press the SELECT button.
29 Computer Input Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the PC Adjust Menu icon. 1 2 Press the Point ed buttons to move the red frame pointer to the item that you want to adjust and then press the SELECT button to display the adjustment dialog box.
30 Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area H Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Display area V Reset Store Exit the PC Adjust Menu. Quit To store the adjusted data, select Store and then press the SELECT button.
31 Computer Input Move the red frame pointer to the mode and press the SELECT button. The level being selected. Image Select Menu Image Select Menu icon IMAGE button Dynamic Real Image 1 Image 2 Image 3 Imag e Mode Selection Image 4 Blackboard (Green) Standard Remote Control IMAGE button Normal picture mode preset on the projector.
32 Press the Point 7 8 buttons to adjust the value. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 1 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the adjustment dialog box.
33 Computer Input Store Exit the Image Adjust Menu. Quit To store the adjusted data, select Store and press the SELECT button. Use the Point ed buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select [Yes].
Remote Control D.ZOOM + button POINT buttons SELECT button D.ZOOM - button 34 Computer Input ✔ Notes: • The panning function may not operate properly if the stored Mode in the PC Adjust Menu is used. (p.30) • The minimum compression ratio can be limited depending on the input signal or when the Keystone function is working.
35 Choose Video by pressing the VIDEO button on the top control or the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Input Menu icon.
36 Choose Computer 2 by pressing the COMPUTER 2 button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. Press the MENU button to display the On-Screen Menu.
37 Video Input Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the AV System Menu icon.
38 Move the red frame pointer to a mode and press the SELECT button. The selected image mode is check marked. Image Select Menu Image Select Menu icon IMAGE button Dynamic Cinema Image 1 Image 2 Image.
39 Video Input Press the Point 7 8 buttons to adjust the value. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon.
40 To store the adjusted data, select Store and press the SELECT button. Use the point ed buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select [Yes]. Stored data can be called up by selecting "Image (1-4)" in the Image Select Menu on page 38.
41 Video Input This projector has the picture screen resize function, which enables you to customize the image size. Wide Normal Scr een Siz e A djustment Adjust the screen scale and position manually with this function.
42 Display Blue back Press the Point 7 8 buttons to switch On/Off. When this function is “On,” a blue image is displayed while the input signal is not detected. Keystone Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon.
43 Setting Capture This function enables you to capture the image being projected and use it for a start-up display or interval of presentations. After capturing the projected image, go to the Logo select function and set it to “User”.
44 Setting Logo PIN code loc k This function prevents an unauthorized person from changing the screen logo. Off ............ The screen logo can be changed freely from the Logo Menu (p.43). On ............ The screen logo cannot be changed without a Logo PIN code.
45 Setting Ceiling Rear Ceiling When this function is set to “On,” the picture will be top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to “On,” the picture will be left/right reversed.
46 Setting On start When this function is “On”, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. ✔ Note: Be sure to turn the projector off properly (see “Turning Off the Projector” on page 20).
47 Setting Key lock If the top control accidentally becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Key lock Select Key lock.
48 Setting Change the PIN code loc k setting Use the Point 7 8 buttons to switch between the options. Use the Point 7 8 button to select Off, On1, or On2 and then move the pointer to “Quit” with the Point d button. Press the SELECT button to close the dialog box.
49 Setting This function provides the following options in the cooling fans’ operation when the projector is turned off (p.20). L1 ....... Normal operation L2 ....... Slower and lower-sound than the normal operation (L1), but it takes more time to cool the projector down.
50 Setting Factory default This function returns all setting values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, and filter counter to the factory default settings. Exit the Setting Menu. Quit Select Factory default and this box appears.
51 The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. Wa r n i ng Indicator The pr ojector is shut do wn and the W ARNING indicator is blinking r ed.
52 Turn off the projector, and unplug the AC power cord from the AC outlet. Turn the projector over and remove the filter by pulling the latches upward.
53 Maintenance and Cleaning Cleaning the Pr oject or Cabinet Cleaning the Pr ojection Lens Slide Shutter is provided to protect the surface of the lens against scratches and dirt. When you are not using the projector, close the Slide Shutter. To open or close, use the Slide Shutter Lever on the top of the cabinet.
54 Maintenance and Cleaning When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
55 Maintenance and Cleaning This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard. ● Lamp life may differ from lamp to lamp and according to the environment of use.
56 Tr oubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on page15-17. – Make sure all equipment is connected to AC outlet and the power is turned on.
57 This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. Appendix The CE Mark is a Directive conformity mark of the European Community (EC).
58 Appendix Menu T r ee Mode 1 Mode 2 SVGA 1 - - - - Auto PC Adj. Fine sync. Total dots Horizontal Vertical Display area - H Display area - V Reset Dynamic Real Blackboard(Green) Image 1 Image 2 Image 3 Image Adjust Contrast Brightness Color temp.
59 Appendix Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL-N V ideo Input Auto 1080i 1035i 720p 575p 480p 575i 480i Dynamic Cinema Blackboard(Green) Image 1 Image 2 Image 3 Quit Normal Wide Custom 0 - 63 0 -.
60 Appendix Check the indicators for projector condition. • • • green. • • • red • • • off • • • blinks green. ✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly.
61 Appendix Compatible Comput er Specifications The projector can basically accept the signal from all computers with the V, H-Frequency mentioned below and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) VGA 1 640 x 480 31.
62 Appendix Te c hnical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 13.15” x 3.07” x.9.13” (334 mm x 78 mm x 232 mm) (Not including adjustable feet) Net Weight 7.5 lbs (3.3 kg) Feet Adjustment 0˚ to approx.
63 Appendix Model No. COMPONENT-VGA Cable : POA-CA-COMPVGA SCART-VGA Cable : POA-CA-SCART VGA-Cable (10m) : KA-MC-DB10 Soft Carrying Case : POA-CAC-VCL2 Laser Pointer Remote Control Unit : POA-RCKIT03 Presentation Kit : POA-RCKIT04 The parts listed below are optionally available.
Dimensions 64 Appendix Terminal : Mini DIN 8-PIN 1 2 3 4 5 8 7 6 SERVICE PORT CONNECTOR R X D ----- ----- GND RTS / CTS GND GND Serial 1 2 3 4 5 6 7 8 COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TER.
65 Appendix Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station.
SANYO Electric Co., Ltd. KL6A.
デバイスSanyo PLC-XU100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo PLC-XU100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo PLC-XU100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo PLC-XU100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo PLC-XU100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo PLC-XU100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo PLC-XU100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo PLC-XU100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo PLC-XU100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
