SanyoメーカーPLC-XU74の使用説明書/サービス説明書
ページ先へ移動 of 66
Multimedia Projector MODEL PLC-XU74 Owner's Manual.
2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology .
T able of Contents 3 T rademarks Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design . . . . . . . . . . . . . 2 T able of Contents . . . . . . . . . . .
4 T o the Owner Before operating this projector , read this manual thoroughly and operate the projector properly . This projector provides many convenient features and functions. Operating the projector properly enables y o u t o m a n a g e th o s e f e a t u r e s a n d m a i n t a i n s i t i n better condition for a considerable time.
5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
Safety Instructions 6 Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent.
Compliance 7 Federal Communication Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
8 Part Names and Functions Back y u !0 !1 q t y o i Front e r Bottom !5 !2 !4 !3 q Infrared Remote Receiver w Zoom Ring e Projection Lens r Focus Ring t Lens Cove r (See page 52 for attaching.) y Exhaust V ents w CAUTION Hot air is exhausted from the exhaust vent.
9 Part Names and Functions Part Names and Functions Part Names and Functions Rear T erminal q w e r t y i u ✽ o r COMPUTER IN 2 / MONITOR OUT This terminal is switchable and can be use d fo r in pu t fr om a c omp ut er a nd v id eo e q u i p m e n t ( c o m p o n e n t o r R G B s c a r t 21-pin) or output to the other monitor .
10 Part Names and Functions q w e t u i o T op Control r y u LAMP REPLACE indicator T urn yellow when the life of the projection lamp draws to an end. (p.54, 60) y W ARNING indicator Emit a red light when the projector detects an abnormal condition.
1 1 Part Names and Functions Part Names and Functions t e !0 i !4 r !5 !3 !1 q w Remote Control y u o !6 !2 q POWER ON-OFF button T urn the projector on or off. (p.18, 19) w VIDEO button Select VIDEO input source. (p.23, 34) e COMPUTER button Select COMPUTER input source.
Part Names and Functions 12 T o insure safe operation, please observe the following precautions: ● Use two (2) AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery . ● Avoid contact with water or liquid.
13 Installation ✔ Note: • The brightness in the room has a great influence on picture quality . It is recommended to limit ambient lighting in order to obtain the best image. • The values shown below are approximate and may vary from the actual sizes.
T o the AC outlet. (200 - 240 V AC) Installation 14 This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor .
Installation 15 Connecting to a Computer Cables used for connection • VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) • USB Cable • Audio Cables (Mini Plug: stereo) ( Not all the cables are supplied with this projector .
Installation 16 Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-VIDEO Cable • Audio Cable (Mini Plug: stereo) ( Not all the cables are supplied with this projector .) ON ON ✔ Note: • When connecting AUDIO OUT to external audio equipment, the projector’s built-in speaker is disconnected.
Installation 17 Installation Connecting to Component Video Equipment Cables used for connection • Audio Cables (Mini Plug :stereo) • Scart-VGA Cable • Component Cable • Component-VGA Cable ( Not all the cables are supplied with this projector .
Basic Operation 18 Connect the projector's AC power cord into an AC outlet. The POWER indicator becomes red. Press the POWER ON-OFF button on the top control or on the remote control. The POWER indicator becomes green and the cooling fans start to operate.
Basic Operation 19 Press the POWER ON-OFF button on the top control or on the remote control, and a message "Power off?" appears on the screen.
Basic Operation 20 How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Me n u. R e fe r to t h e fo l lo w in g p ag e s re g ar d in g e ac h adjustment and setting procedures. Press the Point 7 8 buttons to select a Menu icon to adjust and press the Point ed buttons to select an item to adjust.
Basic Operation 21 Menu Bar PC System Menu Used to select computer system. (p.26) Setting Menu Used to set the projector's operating configurations. (p.41-50) Image Select Menu Used to select an image level among Dynamic, Standard, Real, Blackboard (Green), and Image 1 ~ 4.
Basic Operation 22 Rotate the Zoom Ring to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus. Zoom and Focus Adjustment Zoom Ring (Rear) Focus Ring (Front) If a projected picture has keystone distortion, correct the image with Keystone adjustment.
Basic Operation 23 Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds.
Basic Operation 24 black out ➜ the captured image ➜ normal ➜ • • • • • Press the NO SHOW button on the remote control to black out the i mage. T o restore to norm al, press the N O S H O W b u t t o n a g a i n o r p r e s s a n y o t h e r b u t t o n .
Computer Input 25 Computer Input Choose either Computer 1 or Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below .
Computer Input 26 Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment.
Computer Input 27 Auto PC Adjustment function is provided to automatically adjust Fine sync, T otal dots, Horizontal, and V ertical to conform to your computer .
Computer Input 28 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the PC Adjust Menu icon. Press the Point e d b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust and then press the SELECT button to display the adjustment dialog box.
Computer Input Adjust th e horizont al area dis played by t his proje ctor . Press the Point 7 8 buttons to decrease/increase the value. Display area H A d j u s t t h e v e r t i c a l a r e a d i s p l a y e d b y t h i s p r o j e c t o r. Press the Point 7 8 buttons to decrease/increase the value.
30 Computer Input Select an image level among Dynamic, Standard, Real, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector . Picture level with improved halftone for graphics.
31 Computer Input Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. Press the Point e d b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust, and then press the SELECT button.
Computer Input 32 Store Exit the Image Adjust Menu. Quit T o store the adjusted data, select Store and press the SELECT button. Select a level from Image 1 to 4 with the Point ed buttons and press the SELECT button. A confirmation box appears and then select [Y es].
Computer Input 33 When the Digital zoom + is selected, the On-Screen M e n u d i s a p p e a r s a n d t h e m e s s a g e " D . z o o m + " i s di sp la ye d . Pr es s th e SE L EC T b ut to n t o ex pa nd t he image size. And press the Point ed 7 8 buttons to pan the image.
V ideo Input 34 Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below . Input Source Selection (Video, S-V ideo) Direct Operation Video INPUT button ✳ See Note at the bottom of this page.
Video Input 35 Computer 1 COMPUTER button INPUT button ✳ See Note at the bottom of this page. ✳ Remote Control T op Control INPUT button COMPUTER button Computer 2 Video Computer 1 ✳ Computer 2 Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control.
Video Input 36 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the A V System Menu icon. Video System Selection Press the Point ed buttons to move the red arrow pointer to the syst em that you want to sel ect and then press the SELECT button.
Video Input 37 Select an image level among Dynamic, Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector . Picture level adjusted for the picture with fine tone.
Video Input 38 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon. Press the Point e d b u t t o n s t o m o v e t h e r e d framed pointer to the item that you want to adjust, and then press the SELECT button.
Video Input 39 T o reset the adjusted data, select Reset and press th e S E L EC T b ut t o n . T h e c on f i r m at i o n b ox a p p e a rs and then select [Y es]. All adjustments returns to their previous figures. Reset Press the Point 7 8 buttons to obtain better balance of contrast.
Video Input 40 This projector has the picture screen resize function, which enables you to customize the image size. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Screen Menu icon.
Setting 41 Blue back Press the Point 7 8 buttons to switch On/Off. When this function is "On", a blue image is displayed while the input signal is not detected. Keystone Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Setting Menu icon.
Setting 42 Display Press the Point 7 8 buttons to switch On/Off. This function decides to display On-Screen Displays. On . . . . . . . . . . . . . Show all the On-Screen Displays. Use this function when you want to p r o j e c t i m a ge s a f t e r t h e l a mp becomes bright enough.
Setting 43 Capture This function enables you to capture the image being projected and use it for a start-up display or interval of presentations. After capturing the projected image, go to the Logo select function and set it to "User".
Setting 44 T o Enter the Logo PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer .
Setting 45 Ceiling Wh en t hi s fu n ct io n is " On ", t he p i ct ur e is t op /b o tt om and left/right reversed. This function is used to project the image from a ceiling mounting the projector . Rear When this function is "On", the picture is left/right reversed.
Setting 46 Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period.
Setting 47 Remote control Th i s p r o j e c t o r p r o v id e s t w o d i ff e r e n t r e m o t e c o n tr o l codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.
Setting 48 Key lock Security (Key lock and PIN code lock settings) This function allows you to use Key lock and PIN code lock function to set the security for the projector operation. Thi s fu nct io n loc ks o per at ion o f th e top c on tro l or the remote control.
Setting 49 T o Enter the PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer .
Setting 50 This function is used to reset the lamp replacement counter . When replacing the projection lamp, reset the lamp replacement counter by using this function.
Maintenance and Cleaning 51 The W ARNING indicator shows the state of the function which protects the projector . Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance. W arning Indicator T h e p r o j e c t o r i s s h u t d o w n a n d t h e WA R N I N G indicator is blinking red.
Maintenance and Cleaning 52 T urn off the projector , and disconnect the AC power cord from the AC outlet. T urn over the projector and remove the air filters by pulling the latches upward. Air filters prevent dust from accumulating on the optical elements inside the projector.
Maintenance and Cleaning 53 Cleaning the Projector Cabinet Softly wipe the projector body with a soft, dry cleaning cloth. When it is heavily soiled, use a small amount of mild detergent and finish with a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Maintenance and Cleaning 54 When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow , replace the lamp with a new one promptly .
Maintenance and Cleaning 55 B e s u re t o r e s e t t h e L a m p r e p l a c e m e n t c o u n t e r a f t e r t h e l a m p i s r e p l a c e d . W h e n t h e L a m p replacement counter is reset, the LAMP REPLACE indicator stops lighting. T urn the projector on, press the MENU button to display the On-Screen Menu.
Appendix 56 T roubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on pages15-17. – Make sure all equipment is connected to AC outlet and the power is turned on.
Appendix 57 Some displays are not seen during operations – Check the Display item. (See page 42.) The Remote Control does not work – Check the batteries. – Make sure there is no obstruction between the projector and remote control. – Make sure you are not too far from the projector when using the remote control.
Appendix 58 Menu T ree System (1) Mode 1 Mode 2 SVGA 1 - - - - Computer Input ✽ Systems displayed in the System Menu vary depending the input signal.
Appendix 59 Dynamic Cinema Blackboard (Green) Image 1 Image 2 Image 3 Image Select Image 4 Standard Video Input Auto 1080i 1035i 720p 575p 480p 575i 480i System (2) Auto P AL SECAM NTSC NTSC 4.43 P AL-M P AL-N System (3) Image Adjust Contrast Brightness Color temp.
Appendix 60 Check the indicators for projector condition. Indicators and Projector Condition The projector is off. (The AC power cord is unplugged.) The projector is preparing for stand-by or the projection la m p is b e i ng c o o le d d o wn . Th e p ro j e ct o r ca n n ot b e turned on until cooling is completed.
Appendix 61 Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V , H-Frequency below mentioned and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. MAC LC13 640 x 480 34.
Appendix 62 T echnical Specifications Mechanical Information Projector T ype Multi-media Projector Dimensions (W x H x D) 9.66" x 2.3" x 6.82" (294.5 mm x 69.5 mm x 208 mm) (Not including adjustable feet) Net Weight 5.3 lbs (2.4 kgs) Feet Adjustment 0˚to10.
63 Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards.
64 T erminal: Mini DIN 8-PIN 1 2 3 4 5 8 7 6 SERVICE PORT CONNECT OR USB CONNECTOR (Series B) 2 3 4 1 COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG) T erminal : Analog RGB (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Configurations of T erminals Red (R/Cr) Input/Output Ground (Horiz.
65 Appendix Appendix Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service station.
Part No. 1LG6P1P0156-- (KT6AC) SANYO Electric Co., Ltd..
デバイスSanyo PLC-XU74の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo PLC-XU74をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo PLC-XU74の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo PLC-XU74の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo PLC-XU74で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo PLC-XU74を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo PLC-XU74の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo PLC-XU74に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo PLC-XU74デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
