SanyoメーカーPOA-LN01の使用説明書/サービス説明書
ページ先へ移動 of 52
PJ-Net Or ganizer INSTALLATION and OPERATION of the PJ- Net Organizer This PJ-Net Organizer is an optional product to control and set up a monitor via a network. Attach this product t o t h e m o n i t o r a n d c o n n e c t a n e t w o r k c a b l e .
Compliance Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of t he FC C Ru les. Thes e lim its are desig ned t o pr ovide reasonable protection against harmful interference in a residential installation.
3 Expression/Abbreviation The following abbreviations may appear in this manual: ● Windows 2000,Windows XP ➜ Windows In some cases, the “PJ-Net Organizer” is explained as “this product” or “Network Board” in this manual. The word “monitor” found in this manual means “LCD monitor PJ-Net Organizer” unless otherwise noted.
4 Serial Port Use . . . . . . . . . . . . . . . . . .39 Example of Connection . . . . . . . . . . . . . . . . . . . . .40 Specification and Setting of RS232C Terminal . . .40 Command for controlling the monitor . . . . . . . . . .41 How to set network congiguration on 5 Appendi x .
5 Preparation Features Web Management function With this function, you can watch monitor functio ns such as power status, input mode, sig- nal conditi on, monitor-u se time, etc. through the netwo rk by using the web browser installe d on your compute r .
6 Preparation Recommended Operating Environment To perform the management and setting up the monitor using this product, the environ- ment described below is required.
Installation 7 1.
8 Installation The following are instructions for attaching this product to the monitor and connecting it to the network. Please review the entire procedure to become familiar with it. Check package (p.9) 1 Installation (p.10-12) 2 Network configuration (p.
9 Name and function of each part Name and function of each part Power indicator This illuminates red when the network board is mounted onto the monitor and the AC plug is connected . LAN port Connecting the LAN cable. Input port Connecting the out- put connection from the network board.
10 Installation [1] Mounting 1 Disconnect the AC plug from the monitor. 2 Remove the screws on the back of the cabi- net, and then remove the terminal covers. 3 Insert the network board into the monitor, and fix it with the screws. ✐ The AC cord must be disconnected from AC power outlet when mounting or removing this product.
11 Mounting 4 Set the Option Switch from the UP position to the DOWN position. ✐ Cannot use the serial port of the monitor in this position. Set back to the UP position when the network board is not used.
[2] Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX.
13 [3] Network configuration When you connect a monitor to a network , the ne twork number of monitor must be the same as the network you intend to connect. You should configure monitorʼs network first. Make sure that the moni tor is conn ecte d to the netw ork corr ectl y.
Configure the network with the computer This example explains how to set the following configuration. The default network configuration is set as follows. Make sure that the monitor is connected to the network and then connect the AC cord to the outlet.
15 2 Configure the network of the monitor by using the web browser. 1 . Enter the IP address of the monitor as the URL. The login page will be displayed and login. For further information, please see chapter “2: Basic Setting and Operation” on page 21.
16 Installation Flash Player The Flash Player version 9 or later is required when you control the monitor. If your computer does not have, follow to the message on the control page Flash Player. For further product information or installing, s e e t h e homepage.
17 Installation Windows 2000 This example explains how to set the following network address. 1 Select the Network and Dial-up Connections menu fro m [S tart ] - [Set ting s] m enu . 2 Clic k th e L ocal Are a C onne ctio n i con with rig ht button of the mouse and then select the Properties menu from the popup menu.
18 Configure the network of computer Windows XP This example explains how to set the following network address. 1 Select the Control Panel menu from the [Start] menu. Click the Network and Internet Connectio n and then click the Network o n t he control panel.
Notice about system construction In c as e of in sta ll in g th e m on ito r w it h PJ -N et O rg ani ze r i nto th e ne tw or k constructed with the DHCP/BOOTP server. This PJ-Net Organizer does not support the DHCP/BOOTP server. The static IP address must be configured by the manual.
Note 20.
Basic Setting and Operation 2 21.
This chapter describes basic operations and settings for controlling the monitor via a net- work using this product. It is required that computer and monitor are connected to the net- work and the network address be properly configured.
23 3 Display of setting page The following setting page of the monitor is displayed. Perform the various kinds of set- ting through this page. Press a button of Main Menu to display the control or setting page. ☛ The main menu which can be set up and control the monitor appears on the lower side of the page.
24 Basic Setting and Operation Initial Settings After installing this product onto the monitor, perform the following basic initial setting. Press the Initial Setting button on the main menu to display the initial setting page. The password can be set in this page.
25 Network Configuration Press the Network Setting button on the main menu. The following setting page is dis- played. This page is to set the IP Address, Subnet Mask, Default gateway, DNS (Domain Name Server) and Model ID.
E-mail Setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the monitor or when the panel usage time reaches to setting time. Press the E-Mail Setting button on the main menu and follow the below steps.
27 3 Option (Condition selection for sending alert message) Select "Option" of sub menu.Type the panel usage time that you want to set, and check the condition items under which alert messages will be sent and press the Set button. Please ref er to chapter “ Examples : Type and contents of aler t messages” described on next page.
Examples: T ype and contents of alert mail When the monitor has an abnormality, the following alert messages are sent to the regis- tered E-mail address according to your selected condition. Administrator or user can take an efficient action quickly by receiving this massage.
29 SNMP Setting SNMP Setting This product can be used for SN MP (S imple N etwork M anagement P rotocol ) function. Press the SNMP Setting button on the main menu and follow the below steps.
30 Basic Setting and Operation 4 Trap Option (Selection for sending alert message) Select "Trap Option" of sub menu.Type the panel usage time that you want to set, and check the condition items under which alert messages will be sent and press the Set button.
Controlling the Monitor 3 31.
Check the status of monitor In the "Status" page, you can check the status of the monitor as follows: 1 Status 1 32 Controlling the Monitor Power: Condition of Power Power ON / Power Error /.
33 Check the status of monitor 2 Status 2 Child Lock: Key Lock of Monitor OFF (Unlock) / On RC Inhibition: Button Lock of Remote Control OFF (Unlock) / On Power save : Off/On The monitor turns into power save mode, after 1 minute with no signal.
Control the monitor Press the Control button on the main menu. The sub menu for controlling the monitor will be displayed on the upper side of the page. When you click each control item, the control page is displayed according to the sub menu you selected.
35 2 Input Click the Input on the sub menu. The control page will be displayed. Select an input source with radio button and press the S et button to change the input source. Controlling the monitor 3 Wide Mode Click the Wide Mode on the sub menu. The control page will be displayed.
36 Controlling the monitor 4 Other 1 Click the Other 1 on the sub menu. The control page will be displayed. Select the item of Child Lock, RC Inhibition, or Power save with radio button and press the Set button to change these functions. ✐ The Child Lock, RC Inhibition, or Power save can be selected independently.
37 Controlling the Monitor Make a memo This function can be used as a memo. Press the Memo button on the main menu. The fol- lowing setting page will be displayed.
Note 38.
Serial Port Use 4 39.
This Network Board provides with a serial control port (RS232C) to control the monitor. Example of Connection Control the monitor through network and serial control function.
41 Command for controlling the monitor The below commands for controlling the monitor can be used. Serial Port Use HEX ASCII 43h 30h 30h 0Dh 0Ah 'C' '0' '0' [CR] [LF] EXA.
42 Serial Port Use If you forgot current network configuration, (IP address, subnet mask,password DNS, and default gateway), you can set them to default value via the serial port (RS232C). 1 Send below command (ASCII) to network board W_DEFAULT + [CR] “_” means space.
Appendix 5 43.
44 Appendix Examples of Connection Direct connection Connect the monitor (LCD01) to the control computer (PC05) directly. Monitor Name: LCD01 IP Address : 192.168.0.2 Subnet Mas k : 255.255.255.0 De fault Gate way : 0.0.0.0 DN S : 0.0.0.0 Computer Name: PC10 IP Address : 192.
45 Examples of connection The gateway (Router) installed in the network Connect the monitor (LCD01) to the control computer (PC05) via the gateway. T o another network Network Group: 192.168.200.0 Net work Group: 192.168.10.0 Monitor Name: LCD01 IP Address : 192.
46 Appendix Web browser setting This product is designed to enable the monitor to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser.
47 Web browser setting Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select the Internet Options menu from the Tool menu on the web browser and then select Security tab and click Customize Level … button.
48 Appendix Proxy setting Select the Internet Options menu from the Tool menu on the web browser and then select Connectio n tab and click LAN Settings button. Properly set up your web browser's the proxy server settings according to the local area network environment to which the monitor is connected.
49 Product Specification Product specification Type ......................................Pj-Net Organizer LAN interfac e ........................Applicant regulation IEEE802.
50 Appendix LAN port specification Port Specification pin No. Signal Function 1 TX+ Transfer data (+) 2 TX- Transfer data (-) 3 RD+ Receive data (+) 4 (not used) 5 (not used) 6 RD- Receive data (-) 7 (not used) 8 (not used) 1 2 3 4 5 6 7 8 8-pin modular connector (RJ-45) MAC Address The MAC address is indicated on the rating label.
51 Note.
Printed in Japan Part No. 610 333 5582 (1AA6P1P5387-- IFFNA).
デバイスSanyo POA-LN01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo POA-LN01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo POA-LN01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo POA-LN01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo POA-LN01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo POA-LN01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo POA-LN01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo POA-LN01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo POA-LN01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
