SanyoメーカーVCB-3444の使用説明書/サービス説明書
ページ先へ移動 of 18
INSTRUCTION MANUAL VCB-3444 B/W CCD Camera.
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER ...........
Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes.
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit.
PARTS NAMES 1 Power indicator (POWER) Comes on when the power to the camera is on. 2 Camera setup section • Internal sync ( INT )/Line lock ( LL ) setting • Electronic iris ( EI )/Auto iris ( AI ).
PARTS NAMES F Flange-back lock screw G Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). H Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
PARTS NAMES Concerning auto-iris lenses DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the Auto-iris lens switch to the DC position.
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 9 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera.
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut th e cable at the plug, th en remove appr ox. 8 mm of th e cable shea th and strip about 2 mm f rom ea c h wire.
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Conn e ct to 2 4 V A C UL l isted class 2 po wer supply (sol d separate ly).
SETTINGS Camera setup section • Internal sync (INT)/Line lock (LL) setting • Electronic iris (EI)/Auto iris (AI) setting • Backlight compensation (BLC) setting • Automatic gain control (AGC) setting Iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop.
SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window.
SETTINGS High speed electronic shutter setting Normally, the speed setting switch for the high speed electronic shutter set to the 0 position. This se ts the elect ronic shut ter speed to 1/6 0 sec. The switch can be set as indicated in table A to select one of the 8 speeds available.
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not p erform correctly, please consult your dealer or a Sanyo Authorized Service Centre.
SPECIFICATIONS Scanning system : EIA standard (525 TV lines, 30 frames/sec.) Interlace : 2:1 interlace Image device : 1/ 3 inch soli d state image device CCD Picture elements : 542 (H) x 494 (V) Effec.
SPECIFICATIONS Dimensions Features and specifications are subject to change without prior notice or obligations. ACCESSORIES 1 Lens iris plug (4-pin) .................................................................. 1 pc. 2 Hexagonal wrench .........
SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty .
1AC6P1P2433-- L73Q4/US(0501KP-TVS) 98230002 21605 Plummer Street, Chatsworth, California 91311 Printed in Taiwan L73Q 4/US GB 2001 , 6, 1 8.
デバイスSanyo VCB-3444の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sanyo VCB-3444をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo VCB-3444の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo VCB-3444の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo VCB-3444で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo VCB-3444を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo VCB-3444の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo VCB-3444に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo VCB-3444デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。