SanyoメーカーVCC-6594Pの使用説明書/サービス説明書
ページ先へ移動 of 22
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS VCC-6592P VCC-6594P COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR CCD About this manual • Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
1AC6P1P2424-- L53H2, H4/XE (0901KPS-DSP) Sanyo Electric Co, Ltd. Printed in Japan L53H 2, H4 /XE GB 200 1, 9, 18.
Depen ding on the co ndit ions of use, instal lation and envir onme nt, please be s ure t o ma ke t he a ppr opriat e sett ing s and adjustm en ts. I f you need hel p wit h insta ll ation a nd/ or se ttings , plea se con sult your de ale r. CONTENTS PRECAUTIONS .
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit.
PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Power input terminal • VCC-6592P: 12 V DC input te.
PARTS NAMES 7 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 8 Flange-back adjustment screw (FLANGE BACK ADJ.) 9 Flange-back lock screw (FLANGE BACK LOCK) F Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
PARTS NAMES G Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. H Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens.
CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Check the lens mount Do not use a lens if the length “ L ” is more than 5 mm. That may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera.
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the cabl e at the plug, t hen remove ap pr ox. 8 m m of th e ca ble sh eath an d s trip ab out 2 mm from ea ch wire.
CONNECTIONS (VCC-6592P only) Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 12 V DC adaptor.
CONNECTIONS (VCC-6592P only) Connections to the camera Y/C OUT connector The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Using a coaxial cable (twin type, 75 ohms), connect the Y/C OUT connector from the camera to the S-VIDEO input terminal on the monitor or time lapse VCR.
CONNECTIONS (VCC-6594P only) Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), AC adaptor and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR.
SETTINGS (VCC-6592P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given.
SETTINGS (VCC-6594P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given.
SETTINGS Electronic shutter settings and electronic iris settings When all of these switches are down, electronic shutter (1/50 sec or auto iris setting) is enabled. The electronic shutter can be set to one of 7 speeds as shown in Table A . Furthermore, when all switches are up, electronic iris setting is enabled.
SETTINGS Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 ( MULT ) and 7 ( CENT ) are set to the down ( OFF ) position. Change the backlight compensation switch settings depending on the conditions.
SETTINGS White balance adjustment Normally the switch 8 ( WB ) is set to the down ( ATW : auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 ( WB ) to the up ( M : manual) position, then adjust the colour.
SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window.
TROUBLESHOOTING Bef ore taking the c ame ra for re pair s, plea se check be low to ma ke sure tha t the ca mera is used corre ctly . I f it st ill do es not p erfo rm corre ctly, pl ease consul t yo ur d ealer or a S anyo Aut horized S ervice Ce n tr e.
SPECIFICATIONS Camera: Scanning system : PAL standard (625 TV lines, 25 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 795 (H) x 596.
SPECIFICATIONS Dimensions Features and specifications are subject to change without prior notice or obligations. 12.6 22.4 11 0.5 109 100 1/4 ”– 20 UNC 56 45 28 56 45 28 (VCC-6592P) (VCC-6594P) L5.
デバイスSanyo VCC-6594Pの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo VCC-6594Pをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo VCC-6594Pの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo VCC-6594Pの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo VCC-6594Pで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo VCC-6594Pを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo VCC-6594Pの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo VCC-6594Pに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo VCC-6594Pデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
