SATOメーカーCX200の使用説明書/サービス説明書
ページ先へ移動 of 55
CX200 Desktop Label Printer ®.
1 Rev B SA TO SER VICE MANUAL CX Series Printers General Information 1-1 Overview The SA TO CX Series Printers are compact desktop printers designed especially for bar code labeling and tagging. The CX uses SA TO Command Language, making it simple to integrate with any other SA TO printer models.
2 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-2 Dimensions D H W CX200DT CX200TT Weight 3.1lb./1.41 kg 3.6 lb./1.63 kg Depth 10 in. (254 mm) Heigth 6.
3 Rev B SA TO SER VICE MANUAL CX Series Printers 1-3 Specifications Model CX200DT/CX200TT Print Method Direct Thermal/Thermal T ransfer Resolution 203 dpi 8 dpmm Max. Media W idth 4.65 inches 1 18 mm Min Media W idth 2.0 inches 51 mm Max. Print W idth 4.
4 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-4 Attributes READY INDICA TOR ON-LINE/OFF LINE BUTTON FEED BUTTON TOP CASE P APER GUIDE PLA TEN ROLLER REMOV AL ACCESS SLOTS W ALL MOUNTING SLOTS .
5 Rev B SA TO SER VICE MANUAL CX Series Printers 1-4 Attributes RELEASE LEVERS FOR PRINT HEAD/RIBBON MECHANISM P APER GUIDE (SHOWN WITH LABELS) P APER GUIDE (SHOWN WITHOUT LABELS) SECTION 1 - GENERAL .
6 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-5 Controls, Indicators and Connections The following table summarizes the functions of the various printer controls, indicators, and connections.
7 Rev B SA TO SER VICE MANUAL CX Series Printers 1-5 Controls, Indicators and Connections PIN # DESCRIPTION 2 RXD (printer data input) 3 TXD (printer data output) 5 Ground 7 R TS (printer busy) 8 CTS .
8 Rev B S A T O SE R VICE MANUAL CX Series Printers POWER INPUT READY INDICA TOR ON-LINE/OFF LINE BUTTON FEED BUTTON UNDERSIDE OF PRINTER POWER SUPPL Y AC OUTLET 1. Plug the output of the AC power supply provided with the printer into the connector on the underside of the printer .
9 Rev B SA TO SER VICE MANUAL CX Series Printers 1-5 Controls, Indicators and Connections Connecting the Interface Cable A V AILABLE DB9S SERIAL PORT P ARALLEL PORT CONNECT THIS END OF THE CENTRONICS .
10 Rev B S A T O SE R VICE MANUAL CX Series Printers ALSO REFER T O THE ACCOMP ANYING ILLUSTRA TIONS (NEXT P AGE) 1. Lift open the top case. 2. Press the two print head releases toward the rear of the printer to unlock the print head. The print head will pop up slightly .
11 Rev B SA TO SER VICE MANUAL CX Series Printers P APER GUIDE LIFT PRINT HEAD AND SLIDE UNDER MEDIA MEDIA ROLL FEED BUTTON READY INDICA TOR SECTION 1 - GENERAL INFORMA TION 1-6 Printer Setup Loading .
12 Rev B S A T O SE R VICE MANUAL CX Series Printers ALSO REFER T O THE ACCOMP ANYING ILLUSTRA TIONS 1. Lift open the top cover . 2. Press the two print head releases toward the rear of the printer to unlock the printhead. The print head will pop up slightly .
13 Rev B SA TO SER VICE MANUAL CX Series Printers 10. T urn the take-up knob to pull the ribbon over the print head without any slack. Check to make sure there are no ribbon wrinkles. 11. Lower the print head and press it down firmly until it locks closed on both sides.
14 Rev B S A T O SE R VICE MANUAL CX Series Printers PLACE T AKE-UP CORE INT O LEFT T AKE-UP SPINDLE SECTION 1 - GENERAL INFORMA TION SPRING LOADED RIBBON T AKE-UP KNOB SUPPL Y ROLL PRINT HEAD PULL TH.
15 Rev B SA TO SER VICE MANUAL CX Series Printers SECTION 1 - GENERAL INFORMA TION LOWER THE PRINT HEAD AND PRESS DOWN FIRML Y ON BOTH HEAD LA TCHES TO LOCK THE PRINT HEAD IN POSITION 1-6 Printer Setu.
16 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Preparation for T est Cuts or gouges in the rubber drive roller Dust buildup or other obstructions of the.
17 Rev B SA TO SER VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Preparation for T est Running the software from your 3-1/2 drive 1. A t the DOS prompt, insert the calibration disk in your computer's 3-1/2 disk drive and access the drive.
18 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Print Head / Status Print 1 Access the software 1. Enter 1 at the prompt. 2. As the sequential screens appear , respond to the prompts. R efer to page 26 for an example of a test label.
19 Rev B SA TO SER VICE MANUAL CX Series Printers Access the software 1. Enter 2 at the prompt. 1-7 Printer T est and Calibration Change RS232 Settings 2.
20 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Change RS232 Settings (Continued) Continue to respond to the prompts or enter a choice on the sequential screens. R un a test label to verify that the new RS232 parameters were entered correctly .
21 Rev B SA TO SER VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Set T op of Form (Pitch Of fset) 3 Access the software 1. Enter 3 at the prompt.
22 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Set T op of Form (Pitch Offset), Continued Continue to respond to the prompts or enter a choice on the sequential screens. After the Offset command is sent to the printer , two labels are printed with a single horizontal line at a V=000 print position.
23 Rev B SA TO SER VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Calibrate Printer 4 Access the software 1. Enter 4 at the prompt. 2.
24 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-7 Printer T est and Calibration Calibrate Printer (Continued) Continue to respond to the prompts or enter a choice on the sequential screens. Sequence of events when the Calibration Program is run: 1.
25 Rev B SA TO SER VICE MANUAL CX Series Printers 1. Press and hold in the READ Y indicator . 2. Press and release the FEED button. 3. The printer should begin printing a self -test label.
26 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-8 Basic Operations Printing and Reading a Self-test Label Firmware Revision Serial Number RS232 Setting Current Printer Heat Setting T otal Numbe.
27 Rev B SA TO SER VICE MANUAL CX Series Printers 1-8 Basic Operations Feeding Blank Labels 1. Connect the host and printer serial or parallel ports together using a correctly wired interface cable, (the parallel cable supplied with the printer , or a null modem RS232 cable.
28 Rev B S A T O SE R VICE MANUAL CX Series Printers 1-8 Basic Operations Printer Ready/Standby/Reset Control Pressing the READY indicator a second time will return the printer to On-Line mode (its default condition).
29 Rev B SA TO SER VICE MANUAL CX Series Printers 2-1 Cleaning SA TO America printers need very little maintenance other than occasional cleaning. Clean the printer body as required, using a soft cloth moistened with a mild detergent cleaner . Section 2 1.
30 Rev B S A T O SE R VICE MANUAL CX Series Printers 2-1 Cleaning 5. Confirm that the label sensor is unobstructed. Clean away any obstruction with a soft brush if necessary . 6. R esume the media loading procedure, or if there is already media in the printer , lower and lock the print head.
31 Rev B SA TO SER VICE MANUAL CX Series Printers 2-1 Cleaning CLEAN THE PLA TEN ROLLER LABEL SENSOR MUST REMAIN UNOBSTRUCTED LABEL FEED DIRECTION PLA TEN ROLLER.
32 Rev S A T O SE R VICE MANUAL CX Series Printers.
33 Rev B SA TO SER VICE MANUAL CX Series Printers Parts Replacement 3-1 Preparing the Printer for Service Caution! Some of the components in the printer are extremely sensitive to static discharge damage. When servicing the printer , observe good static prevention practices.
34 Rev B S A T O SE R VICE MANUAL CX Series Printers Refer to the Section Number for method of replacement 3-2 Replaceable Parts The following is a list of replaceable parts covered in these instructions.
35 Rev B SA TO SER VICE MANUAL CX Series Printers 3-2 Replaceable Parts BOTT OM CASE PLA TEN GEAR CLUSTER SWITCH FRONT CASE PCA BASE BOARD PCBA MODULE PRINT HEAD TOP CASE PLA TEN MOT OR.
36 Rev B S A T O SE R VICE MANUAL CX Series Printers 3-2 Replaceable Parts Location BOTT OM CASE GEAR CLUSTER SWITCH FRONT CASE PCA BASE BOARD PCBA MODULE PRINT HEAD TOP CASE PLA TEN MOT OR PRINT HEAD.
37 Rev B SA TO SER VICE MANUAL CX Series Printers 3-3 T op Case Removal/Replacement REFER T O THE ILLUSTRA TION 1. Lift open the top case 2. Press the two sides of the top case outward to unlatch from the bottom case, and remove.
38 Rev B S A T O SE R VICE MANUAL CX Series Printers 3-4 Chassis, Including the Front Case Removal/Replacement The chassis must be removed to access and remove other components that are fastened to the chassis body . The front case is set in slots in the bottom case and both are removed from the chassis as a unit.
39 Rev B SA TO SER VICE MANUAL CX Series Printers FRONT CASE CHASSIS BOTTOM CASE T o replace the chassis and front case: 1. While lowering the chassis into the bottom case, guide the communication port connectors through the slot in the bottom rear of the bottom case.
40 Rev B S A T O SE R VICE MANUAL CX Series Printers 3-5 Platen Removal/Replacement Platen removal: 1. Raise the top case. 2. Press the two print head release latches back to release the print head, then lift the print head until it is fully raised and latched in the open position.
41 Rev B SA TO SER VICE MANUAL CX Series Printers 3-6 Print Head Removal/Replacement Print head removal: 1. Raise the top case. 2. Press the two print head release latches back to release the print head, then lift the print head until it is fully raised and latched in the open position.
42 Rev B S A T O SE R VICE MANUAL CX Series Printers Print head installation: R everse the above steps to install the print head. 3-6 Print head Removal/Replacement SLIDE FRONT EDGES A W A Y FROM SLOT.
43 Rev B SA TO SER VICE MANUAL CX Series Printers 3-7 PCBA Module Removal/Replacement REFER T O THE ACCOMP ANYING ILLUSTRA TIONS Module removal: 1. R emove the printer chassis according to the instructions in Section 3-4.
44 Rev B S A T O SE R VICE MANUAL CX Series Printers 3-8 PCA Base Board Removal/Replacement REFER T O THE ACCOMP ANYING ILLUSTRA TIONS PCA board removal: 1. R emove the printer chassis according to the instructions in Section 3-4. 2. R emove the module from the main PCA board according to the instructions in Section 3-7.
45 Rev B SA TO SER VICE MANUAL CX Series Printers Motor removal: 1. R emove the printer chassis according to the instructions in Section 3-4. 2. R emove the two Phillips-head screws holding the PCA base board in place. 3. Lift the PCA base board gently , then unplug the feed switch connector at J13 4.
46 Rev B S A T O SE R VICE MANUAL CX Series Printers 3-10 Head Open Switch Removal/Replacement REFER TO THE ACCOMP ANYING ILLUSTRA TIONS Switch removal: 1. R emove the printer chassis according to the instructions in Section 3-4. 2. Insert a flat-bladed screwdriver under the switch body and gently pry it up to detach from the chassis protrusions.
47 Rev B SA TO SER VICE MANUAL CX Series Printers 3-1 1 Cluster Gear Removal/Replacement (Continued) REFER T O THE ACCOMP ANYING ILLUSTRA TIONS Cluster gear removal: 1. R emove the chassis according to the instructions in Section 3-4. 2. R emove the platen according to the instructions in Section 3-5.
48 Rev B S A T O SE R VICE MANUAL CX Series Printers.
49 Rev B SA TO SER VICE MANUAL CX Series Printers T roubleshooting 4-1 Preliminary T ests SA TO printers are very reliable, so printing problems are unlikely .
50 Rev B S A T O SE R VICE MANUAL CX Series Printers 4-2 Common Problems and Their Solutions READY light glows red 1. Press the FEED switch to assure that the printer is not paused in batch mode printing. 2. Confirm that the print media is not exhausted.
51 Rev B SA TO SER VICE MANUAL CX Series Printers 4-2 Common Problems and Their Solutions (Continued) Host stops responding or displays "printer not ready" message 1. R eview your software setup, following the instructions provided with the software.
52 Rev B S A T O SE R VICE MANUAL CX Series Printers 4-2 Common Problems and Their Solutions (Continued) Printer feeds too many labels 1. V erify correct label loading (Eye-Mark bars, if any facing down). 2. Print a test label to confirm that the printer is set for the proper sensor type.
53 Rev B SA TO SER VICE MANUAL CX Series Printers 4-2 Common Problems and Their Solutions (Continued) Ribbon wrinkles Occasional ribbon wrinkling may not indicate a printer problem, but if wrinkling occurs often, check the following: 1. Raise the print head.
54 Rev B S A T O SE R VICE MANUAL CX Series Printers Host stops responding or displays "printer not ready" message 1. R eview your software setup, following the instructions provided with the software. 2. Confirm that the host-to-printer communication cable is connected and undamaged.
デバイスSATO CX200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
SATO CX200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSATO CX200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SATO CX200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SATO CX200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SATO CX200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSATO CX200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SATO CX200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSATO CX200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
