Saturnメーカー2004 Vueの使用説明書/サービス説明書
ページ先へ移動 of 392
Seats and Restraint Systems ........................... 1 - 1 Front Seats ............................................... 1 - 2 Rear Seats ............................................... 1 - 8 Safety Belts .............................................
SATURN, the SATURN Emblem, and the name VUE are registered trademarks of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corportation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols There are a number of safety cautions in this book.
Vehicle Damage Warnings Also, in this manual you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
These are some examples of symbols that may be found on the vehicle: v.
✍ NOTES vi.
Front Seats ..................................................... .1-2 Manual Seats ............................................... .1-2 Driver Seat Height Adjuster ............................. .1-3 Six-Way Power Driver Seat .........................
Front Seats Manual Seats { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Driver Seat Height Adjuster If your vehicle has a driver’s seat height adjuster, it is located on the outboard side of the seat. To raise the seat, ratchet the lever upward until the seat is at the desired height. To lower the seat, ratchet the lever downward until the seat is at the desired height.
Manual Lumbar If your vehicle has this feature, the knob is located on the inboard side of the driver’s seatback. Turn the knob forward or rearward to increase or decrease the lumbar support. Heated Seats Your vehicle may have heated seats. The switches are located below the climate control system.
Reclining Seatbacks To adjust the seatback, lift the lever on the outboard side of the seat and move the seatback to where you want it. Then release the lever to lock the seatback in place.
But don’t have a seatback reclined if your vehicle is moving. { CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Head Restraints Press the button on the side of the head restraint to adjust it. Adjust your head restraint so that the top of the restraint is closest to the top of your head.
Passenger Folding Seatback The front passenger’s seatback folds flat. To fold the seatback, do the following: 1. Lift the bar under the seat to unlock it. 2. Slide the seat as far back as it will go and release the bar. Try to move the seat with your body to make sure it is locked into place.
{ CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. { CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash.
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. { CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-12.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-13.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Q: What’s wrong with this? A: The shoulder belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What’s wrong with this? A: The belt is buckled in the wrong place. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Q: What’s wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What’s wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your retailer to fix it.
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-15 . The right front passenger’s safety belt works the same way as the driver’s safety belt — except for one thing.
2. Push the latch plate into the buckle until it clicks. If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle it. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-28 .
The safety belt locks if there is a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
1. Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip. 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide.
3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-23 . Make sure that the shoulder belt crosses the shoulder.
Safety Belt Pretensioners Your vehicle has safety belt pretensioners. Although you cannot see them, they are located on the retractor part of the safety belts for the driver and right front passenger. They help the safety belts reduce a person’s forward movement in a moderate to severe frontal or near frontal crash.
Q: What is the proper way to wear safety belts? A: If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
Q: What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? A: If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones in a crash. Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children.
{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle.
A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system.
Q: How do child restraints work? A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
{ CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. Always secure a rear-facing child restraint in a rear seat.
In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. Anchor the top strap to an anchor point specified in Top Strap Anchor Location on page 1-39 .
Top Strap Anchor Location Your vehicle has one of the following top strap anchors already installed for the rear seating positions. Do not secure a child restraint in the right front passenger’s pos.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will find anchors for each rear seating position. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts.
A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchorages for this chi.
Securing a Child Restraint Designed for the LATCH System 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-40 .
3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 4. The safety belts in the rear outside seating positions have a child restraint locking feature.
5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-40 . See Top Strap on page 1-37 if the child restraint has one.
3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Airbag Systems This part explains the air bag systems. Your vehicle has a frontal air bag for the driver and another frontal air bag for the right front passenger.
CAUTION: (Continued) They are not designed to inflate in frontal, in rollover or in rear crashes. Everyone in your vehicle should wear a safety belt properly — whether or not there is an airbag for that person. { CAUTION: Both frontal and side impact airbags inflate with great force, faster than the blink of an eye.
There is an air bag readiness light on the instrument panel cluster, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-28 for more information.
The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. If your vehicle has a side impact airbag for the driver and the person seated directly behind the driver, it is in the ceiling above the side windows.
If your vehicle has a side impact airbag for the right front passenger and the person seated directly behind that passenger, it is in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? The driver’s and right front passenger’s frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact exceeds a predetermined deployment threshold.
In any particular crash, no one can say whether an airbag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near-frontal impacts.
What Will You See After an Airbag Inflates? After the airbag inflates, it quickly deflates, so quickly that some people may not even realize the airbag inflated.
In many crashes severe enough to inflate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for your airbag system.
{ CAUTION: For up to 10 minutes after the ignition key is turned off and the battery is disconnected, an airbag can still inflate during improper service. You can be injured if you are close to an airbag when it inflates. Avoid yellow connectors. They are probably part of the airbag system.
Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts.
If you have had a crash, do you need new belts or LATCH system parts? After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be if worn during a more severe crash, then you need new parts. If the LATCH system was being used during a more severe crash, you may need new LATCH system parts.
✍ NOTES 1-60.
Keys .............................................................. .2-2 Remote Keyless Entry System ........................ .2-3 Remote Keyless Entry System Operation .......... .2-4 Doors and Locks ............................................ .2-7 Door Locks .
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
Have extra keys made. Your service parts department can make extra keys for you. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in.
Remote Keyless Entry System Operation With this feature, you can lock and unlock the doors from about 32 feet (10 m) away using the remote keyless entry transmitter supplied with your vehicle. Q (Lock): Press this button on the remote keyless entry transmitter to lock the doors.
Active Arming: The system will arm when the lock button on the remote keyless entry transmitter is pressed. The system will disarm when the unlock button is pressed. Passive Arming: The system will arm itself one minute after the ignition is turned off and the driver’s door has been opened and closed.
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Power Door Locks Press the bottom half of the switch on either front door to lock all of the doors. Push the top half of the switch to unlock all of the doors. The unlocked door indicators on the manual door lock pins will be hidden when the doors are locked.
Programmable Automatic Door Locks With this feature, all the doors will lock as the transaxle is shifted out of PARK (P) if the ignition key is in RUN and all doors are closed. The doors will automatically lock if the vehicle is going faster than 3 mph (5 km/h).
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside. To cancel the rear door security lock, do the following: 1.
Vehicles with Power Door Locks Use your keyless entry transmitter or power door locks to unlock the liftgate. To open it, lift the handle located in the center of the liftgate. Vehicles with Manual Door Locks The liftgate will lock when the gear shifter is moved out of PARK (P).
Power Windows If your vehicle has this feature the switches are located on each side of the shift lever on the console. To open a window press the switch down and lift up to close it. The power windows can operate only when the ignition key is in RUN or ACC.
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Passlock ® Your vehicle is equipped with the Passlock ® theft-deterrent system.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one speed, fast or slow, for the first 500 miles (805 km).
Notice: If your key seems stuck in LOCK and you cannot turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard. Turn the key only with your hand. Using a tool to force it could break the key or the ignition switch.
Starting Your Engine 1. With your foot of f the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner.
Engine Coolant Heater If your vehicle has this feature, in very cold weather 0°F ( − 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Automatic Transaxle Operation Five-Speed Automatic and VTi Variable If your vehicle is equipped with either the five-speed automatic transaxle or the VTi variable automatic transaxle, the shift lever is located on the console between the seats. There are several different positions for the automatic transaxle.
If you cannot shift out of PARK (P), ease pressure on the shift lever — push the shift lever all the way into PARK (P) and also release the shift lever button as you maintain brake application. Then move the shift lever into the gear you wish. Press the shift lever button before moving the shift lever.
AUTOMATIC OVERDRIVE (D): This position is for normal driving with the automatic transaxle. If you need more power for passing, and you are: • Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. • Going about 35 mph (55 km/h), push your accelerator all the way down.
3. Insert the end of your ignition key into the slot and press down firmly. 4. Apply the brake and move the shift lever to NEUTRAL (N). 5. While maintaining brake application, start the vehicle and move the shift lever into the desired gear position.
SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD (3), FOURTH (4) and FIFTH (5): Shift into THIRD (3), FOURTH (4) and FIFTH (5), the same way you do for SECOND (2).
While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator. Ignore the light when you downshift.
Shifting Into Park (P) (Automatic Transaxle) { CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Leaving Your Vehicle With the Engine Running { CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Shifting Out of Park (P) (Automatic Transaxle) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transaxle Operation on page 2-18 .
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you.
Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit.
2. Press and hold the on/of f button until a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/of f button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the comp/temp display will return.
Automatic Dimming Mirror Operation Press the COMP button to turn the automatic dimming feature on and off. An indicator light on the bottom of the mirror face will be on when the automatic dimming feature is on. Compass Operation Press the COMP button once briefly to turn the compass on or off.
2. Press and hold the COMP button for five seconds until a zone number appears in the display. 3. Press the COMP button on the bottom of the mirror until the new zone number appears in the display. After you stop pressing the button, the display will show a compass direction within a few seconds.
Outside Power Mirrors If the vehicle has this feature, the controls are located on the driver’s side of the vehicle next to the shift lever. Move the selector switch to the left or right to choose the mirror to be adjusted; then press the four-way control pad to adjust the direction of the mirror.
OnStar ® System Your vehicle may have this feature. OnStar ® uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services.
Directions and Connections Plan • All Safe and Sound Plan services • Route Support • RideAssist • Information and Convenience Services Luxury and Leisure Plan • All Directions and Connection.
Load Floor Storage Box Some models have a load floor storage box, which is located in the rear of the vehicle. This storage space is designed to hold small items.
Sunroof The vehicle may have an express-open sunroof. The sunroof switch is located above the rearview mirror. To operate the sunroof, the key must be in the RUN or ACC position. To express-open the sunroof glass panel and sunshade, press the switch rearward and release it.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 Horn ............................................................ .3-6 Tilt Wheel ..............................................
Audio System(s) ............................................ .3-42 Setting the Time for Radios without Radio Data Systems (RDS) ....................... .3-43 Setting the Time for Radios with Radio Data Systems (RDS) ....................... .3-43 AM-FM Radio .
✍ NOTES 3-3.
Instrument Panel Overview 3-4.
The main components of the instrument panel are the following: A. Air Outlets. See Climate Control System on page 3-21 . B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7 . C. Cruise Control (If Equipped). See Cruise Control (2.
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located near the center of the instrument panel.
Tilt Wheel Your vehicle has a tilt wheel which allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you exit and enter the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column.
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.
The exterior lamp control has the following three positions: 9 (Off) (Base Level Only): Turn the control to this position to turn off exterior lamps. AUTO (Uplevel Only): If equipped, turn the control to this position to put the headlamps in automatic mode.
OOOO : Put the lever in this position for rapid wiping cycles. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, gently loosen or thaw them. If the blades do become damaged, install new blades or blade inserts.
Cruise Control (2.2L L4 Engine) Your vehicle may be equipped with cruise control. The buttons for the cruise control are located on the steering wheel.
Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: • Press set/coast button until you reach the lower speed you want, then release it. • To slow down in very small amounts, briefly press the set/coast button.
Cruise Control (3.5L V6 Engine) Your vehicle may be equipped with cruise control. The buttons for the cruise control are located on the steering wheel.
Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: • Press set/coast button until you reach the lower speed you want, then release it. • To slow down in very small amounts, briefly press the set/coast button.
Exterior Lamps Headlamps See Turn Signal/Multifunction Lever on page 3-7 for more information on the headlamps. Daytime Running Lamps Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day.
Automatic Headlamp System If your vehicle has this feature and when it is dark enough outside, the headlamps will come on automatically. Your vehicle has a light sensor located on top of the instrument panel. Make sure it is not covered, or the headlamps will be on when you don’t need them.
Interior Lamps Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The thumbwheel for this feature is located on the instrument panel to the left of the steering column. Turn the thumbwheel to the right to brighten the lights or to the left to dim them.
Map Lamps The lamps are located on the headliner above the rearview mirror. To turn the lamps on, press the lens. Press the lens again to turn them off. Battery Run-Down Protection Your vehicle is equipped with a battery saver feature designed to protect your vehicle’s battery.
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Operation To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets.
# (Air Conditioning): Press this button to turn the air-conditioning system on or off. When this button is pressed, an indicator light above the button will come on to let you know the air conditioning is activated. Air-conditioning can be selected in any mode as long as the fan switch is on.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN.
The filter should be replaced as part of routine scheduled maintenance. See Scheduled Maintenance on page 6-4 for replacement intervals. See your retailer for details on changing the filter. To find out what type of filter to use, see Normal Maintenance Replacement Parts on page 6-16 .
4. Remove the filter by sliding it out of the housing. 5. Install the new air filter. When installing a new air filter make sure the AIR FLOW arrow is pointing rearward. 6. Install the air filter access panel. 7. Install the air filter access panel push pins.
Instrument Panel Cluster The instrument cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles or kilometers. Your vehicle has a tamper-resistant odometer.
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will flash for several more.
{ CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inflate in a crash, or they could even inflate without a crash.
Up-Shift Light Your vehicle may have up-shift light. When this light comes on, you should shift to the next higher gear if weather, road, and traff ic conditions allow you to. This light is located in your instrument panel cluster under your temperature gage.
The BRAKE light will also come on to indicate a low brake fluid level. See Brakes on page 5-41 for more information. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor.
If the light remains on after resetting the system or comes on again while driving, your vehicle needs service. If the ABS light is on, but the regular brake system warning light is not on, you do not have anti-lock brakes, but you still have regular brakes.
Low Traction Light If your vehicle has the Traction Control System (TCS), this light will come on when the system is limiting wheel spin. You may feel or hear the system working, but this is normal. The roads may be slippery if this light comes on. Adjust your driving accordingly.
Engine Coolant Temperature Gage This gage measures the temperature of the vehicle’s engine. If the indicator needle moves into the shaded area, the engine is too hot.
Malfunction Indicator Lamp Service Engine Soon Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems.
If the Light Is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed • Avoiding hard accelerations • Avoiding steep uphill grades • If you are towin.
If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your retailer can check the vehicle.
Oil Pressure Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem.
Change Engine Oil Light If this light comes on, it means that service is required for your vehicle. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-15 for more information. After having the oil changed you will need to reset the light. See Engine Oil on page 5-15 for more information.
Daytime Running Lamps (DRL) Indicator Light This light is located on the instrument panel cluster. It goes on whenever the Daytime Running Lamps are on. See Daytime Running Lamps under Exterior Lamps on page 3-17 for further information. Gate Ajar Light If this light comes on, your liftgate is not completely closed.
Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank. When the indicator nears empty, the low fuel light will come on. You still have a little fuel left, but you should get more soon. See Low Fuel Warning Light on page 3-42 for more information.
Low Fuel Warning Light The light next to the fuel gage will come on briefly when you are starting the engine. This light also comes on when the fuel tank is low on fuel. When you add fuel the light should go off. If it doesn’t, have your vehicle serviced.
Setting the Time for Radios without Radio Data Systems (RDS) Press and hold the RCL button, at the same time press the TUNE/SEEK down or up arrows. Press the arrows until the correct time appears on the display. The time can be set with the ignition on or off.
Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. R TUNE Q : Press either arrow to select radio stations. R SEEK Q : Press and hold the up or the down arrow to go to the next or to the previous station and stay there.
Cancelling Automatic Set The radio retains the previously stored stations so they can be recalled when automatic set is canceled. Press and hold the AM FM until you hear a beep. A.SET will no longer appear on the display. Setting the Tone (Bass/Treble) BASS: Press this knob lightly so it extends.
Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. R TUNE Q : Press the up or down arrow to select radio stations. R SEEK Q : Press and hold the up or the down arrow to go to the next or to the previous station and stay there.
Cancelling Automatic Set The radio retains the previously stored stations so they can be recalled when automatic set is canceled. Press and hold AM FM until you hear a beep. A.SET will no longer appear on the display. Setting the Tone (Bass/Treble) MODE: Press this button until BAS or TRE appears on the display.
If an error appears on the display, see “CD Messages” later in this section. 1 PRV (Previous): Press this pushbutton to go to the start of the current track if more than eight seconds have played. If this pushbutton is held or pressed more than once, the player will continue moving backward through the CD.
CD Messages ERR (Error): If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road.
With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages fr.
Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. AUX (Auxiliary): Press this button to switch between XM1 and XM2 (if equipped). While in XM you can perform the following: • Press either CAT arrow to select different categories.
5. Press and hold one of the six numbered pushbuttons. Preset X Stored will appear on the display and you will hear a beep. Whenever that numbered pushbutton is pressed, the station that was set will return and the equalization that was selected will be stored for that pushbutton.
Adjusting the Speakers (Balance/Fade) QP (Balance/Fade): To adjust the balance between the right and the left speakers, press this knob until BAL appears on the display.
4 (Information): If the current station has a message, the information symbol will appear on the display. Press this button to see the message. The message may display the artist, song title, call in phone numbers, etc. If the entire message is not displayed, parts of the message will appear every three seconds.
If playing a CD-R the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. There may be an increase in skipping, diff iculty in finding tracks, and/or dif ficulty in loading and ejecting.
O (Tune): Turn this knob to quickly change tracks. 4 (Information): Press this button to view CD text information, if available. To change the default on the display to track name, album name, or artist name, instead of elapsed track time, press this button to view the available information.
M (Load): Press this button to load CDs into the CD player. This CD player will hold up to six CDs. To load one CD, do the following: 1. Turn the ignition on. 2. Press the load button for less than three seconds. 3. Press the pushbutton (1-6) for the CD slot to load.
5/RDM (Random): Press and release this pushbutton to hear the tracks on the current CD in random, rather than sequential, order. RDM will appear on the display. Press RDM again to turn off random play. Press and hold RDM for two seconds to hear the tracks on all of the CDs loaded in random, rather than sequential, order.
AUX (Auxiliary): Press this button to play a CD or to switch to XM1 or XM2 when listening to the radio. B (CD): Press this button to go to the next CD, if more than one CD is loaded. Z (Eject): To eject one CD, press this button for less than two seconds.
• There are a total of 20 directories (folders) allowed on a CD. The file structure can be 4 directories deep (a folder within a folder, within a folder, etc.). Anything more than 20 directories will be ignored. Each directory may have up to 99 files contained within it.
2 l (Next): Press this pushbutton to go to the next track. If this pushbutton is held or pressed more than once, the player will continue moving forward through the current directory. 4: Press this pushbutton to enter playlist mode. Use the tune knob to cycle through the available playlists.
Radio Personalization This radio has a personalization feature. You can change the following features: Clock Function: Change the time of the day displayed on the radio between 12 hour and 24 hour. Language: This radio supports three languages: ENG (English), FRE (French), and SPA (Spanish).
Headphones The RSE system includes two sets of wireless headphones. The headphones are used to listen to the DVD radio or an auxiliary device connected to the RCA jacks. The wireless headphones have an ON/OFF switch and a volume control. To use the headphones, turn the switch to ON.
Stereo RCA Jacks The RCA jacks are located behind the video screen on the overhead console. The RCA jacks allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE. Adapter connectors or cables may be required to connect the auxiliary device to the RCA jacks.
When a CD is inserted, the radio may be put into RSE mode by pressing the RSE button. The rear seat passengers will be able to listen to the CD through the wireless headphones.
DVD Radio The DVD radio is located in the center of the instrument panel. The DVD radio is controlled by the buttons on the remote control. See “Remote Control” later in this section for more information. The DVD radio is only compatible with DVDs authorized for use in the United States and Canada (Region Code 1).
Playing a Disc To play a disc, gently insert the disc, with the label side up, into the loading slot. The DVD player will continue loading the disc and the player will automatically start. If a DVD is already in the radio, press the play/pause button on the remote control to start playing the disc, when the DVD system is active.
Remote Control To use the remote control, aim it at the transmitter window below the video screen and press the desired button. Direct sunlight or very bright light may affect the ability of the RSE transmitter to receive signals from the remote control.
z (Set-up Menu): Press this button to adjust the color, tint, brightness, contrast, and display mode (normal, full, or zoom). The dynamic range compression feature can be used to reduce loud audio and increase low audio produced by some DVDs. e (Audio): Press this button to display a menu that will only appear when a DVD is playing.
q (Return): Press this button to exit the current active menu and return to the previous menu. This button will operate only when a DVD is playing and a menu is active. | (Camera Angle): Press this button to change camera angles on DVDs that have this feature when a DVD is playing.
DVD Display Error Messages The video screen may display one of the following: Disc Format Error: This message is displayed when a disc is inserted upside down, not readable, or if the disc format is not compatible. The disc will be automatically ejected from the radio.
Theft-Deterrent Feature The Radio with Single CD (MP3) and the Radio with Six-Disc CD (MP3) have a theft deterrent feature. The theft deterrent feature is designed to discourage theft of your vehicle’s radio. It works by using a secret code to disable all radio functions whenever battery power is interrupted.
8. Press the TUNE up or AUTO EQ right arrow to make the fourth digit agree with your code. 9. Press AM-FM after you have confirmed that the code matches the secret code you have written down. The display will prompt you to repeat Steps 5 through 8 to confirm your secret code.
Disabling the Theft-Deterrent Feature Enter your secret code as follows; pause no more than 15 seconds between steps: Preform Steps 1 through 9 from the “Activating the Theft-Deterrent Feature” earlier to enter your secret code. OFF will appear on the display indicating the theft deterrent feature is off.
Care of Your CDs and DVDs Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
✍ NOTES 3-76.
Your Driving, the Road, and Your Vehicle ......... .4-2 Driver Behavior ............................................. .4-2 Driving Environment ....................................... .4-2 Vehicle Design .............................................. .
Your Driving, the Road, and Your Vehicle Whenever we drive, we are taking on an important responsibility. This is true for any motor vehicle — passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle’s design all affect how well a vehicle performs.
This means that you should not expect a utility vehicle to handle the same way a vehicle with a lower center of gravity, like a car, would in similar situations. But driver behavior factors are far more often the cause of a utility vehicle rollover than are environmental or vehicle factors.
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year.
It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having a collision. At a BAC level of 0.10 percent, the chance of this driver having a collision is 12 times greater; at a level of 0.
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road.
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traff ic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
This light will come on when your traction control system is limiting wheel spin. See Low Traction Light on page 3-33 . You may feel or hear the system working, but this is normal. The traction control system automatically comes on whenever you start your vehicle.
If the system is limiting wheel spin when you press the button, the light on the button will go off, but the system will not turn off until there is no longer a current need to limit wheel spin. You can turn the system back on at any time by pressing the button again.
Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Of f-Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy.
• Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems.
Operating Your All-Wheel-Drive Vehicle Of f Paved Roads This off-road guide is for vehicles that have all-wheel drive. If your vehicle does not have all-wheel drive, you should not drive off-road unless you are on a level, solid surface.
{ CAUTION: • Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks. • Unsecured cargo on the load floor can be tossed about when driving over rough terrain.
Traveling to Remote Areas It makes sense to plan your trip, especially when going to a remote area. Know the terrain and plan your route. You are much less likely to get bad surprises. Get accurate maps of trails and terrain. Try to learn of any blocked or closed roads.
Scanning the Terrain Off-road driving can take you over many dif ferent kinds of terrain. You need to be familiar with the terrain and its many different features. Here are some things to consider. Surface Conditions: Of f-roading can take you over hard-packed dirt, gravel, rocks, grass, sand, mud, snow or ice.
Driving on Of f-Road Hills Off-road driving often takes you up, down or across a hill. Driving safely on hills requires good judgment and understanding of what your vehicle can and cannot do. There are some hills that simply cannot be driven, no matter how well built the vehicle.
Driving Uphill Once you decide you can safely drive up the hill, you need to take some special steps. • Use a low gear and get a firm grip on the steering wheel. • Get a smooth start up the hill and try to maintain your speed. Do not use more power than you need, because you do not want your wheels to start spinning or sliding.
Q: What should I do if my vehicle stalls, or is about to stall, and I cannot make it up the hill? A: If this happens, there are some things you should do, and there are some things you must not do? First, here is what you should do: • Push the brake pedal to stop the vehicle and keep it from rolling backwards.
Q: Suppose, after stalling, I try to back down the hill and decide I just cannot do it. What should I do? A: Set the parking brake, put your transaxle in PARK (P) (or FIRST (1) if you have a manual transaxle) and turn off the engine. Leave the vehicle and go get some help.
Q: Are there some things I should not do when driving down a hill? A: Yes! These are important because if you ignore them you could lose control and have a serious accident. • When driving downhill, avoid turns that take you across the incline of the hill.
Also, driving across an incline puts more weight on the downhill wheels. This could cause a downhill slide or a rollover. • Surface conditions can be a problem when you drive across a hill. Loose gravel, muddy spots, or even wet grass can cause your tires to slip sideways, downhill.
Stalling on an Incline If your vehicle stalls when you are crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
{ CAUTION: Driving on frozen lakes, ponds or rivers can be dangerous. Underwater springs, currents under the ice, or sudden thaws can weaken the ice. Your vehicle could fall through the ice and you and your passengers could drown. Drive your vehicle on safe surfaces only.
After Of f-Road Driving Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a fire hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you cannot see as well, you may need to slow down and keep more space between you and other vehicles.
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you cannot, try to slow down before you hit them. { CAUTION: Wet brakes can cause accidents.
Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle.
City Driving One of the biggest problems with city streets is the amount of traff ic on them. You will want to watch out for what the other drivers are doing and pay attention to traff ic signals. Here are ways to increase your safety in city driving: • Know the best way to get to where you are going.
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traff ic and keep to the right.
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever.
If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all fluid levels and also the brakes, tires, cooling system, and transaxle.
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle.
What is the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32°F; 0°C) and freezing rain begins to fall.
If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: • Turn on your hazard flashers.
{ CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking your exhaust pipe.
If You Are Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you do not want to spin your wheels too fast. The method known as “rocking” can help you get out when you are stuck, but you must use caution.
Vehicles Equipped with VTi Variable Transmission If you press too hard on the accelerator pedal, you may not be able to shift into DRIVE (D) or REVERSE (R). If this happens, release the accelerator pedal, then shift to the gear you want. Recovery Hook Contact your retailer if you would like to have a recovery hook installed on your vehicle.
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing” following.
Dinghy Towing (Manual or Five-Speed Automatic Transaxle*) To tow your vehicle from the front with all four wheels on the ground, do the following: 1. Position and attach the vehicle to tow it behind the recreational vehicle. 2. Turn the ignition key to ACC.
Once you have reached your destination, do the following: 1. Set the parking brake. 2. Shift the transaxle to FIRST (1) for manual transaxle. 3. Turn the ignition key to LOCK and remove the key from the ignition. 4. Replace the large IGNITION fuse. Notice: Too much or too little fluid can damage the transaxle.
4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Release the parking brake. Towing Your Vehicle From the Rear Notice: Towing your vehicle from the rear could damage it. Also, repairs would not be covered by the warranty.
Tire and Loading Information Label A. Vehicle Capacity Weight The Tire and Loading Information label is attached to the center pillar, near the driver’s door latch. Vehicles without a center pillar will have the Tire and Loading Information label attached to the driver’s door edge.
4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs.
Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 2 = 1,000 lbs. (453 kg) B Subtract Occupant Weight 150 lbs. (68 kg) × 5 = 750 lbs. (340 kg) C Available Occupant and Cargo Weight = 250 lbs. (113 kg) Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs.
Certification/Tire Label The Certification/Tire label is located on the rear edge of the driver’s door. The label shows the proper size and speed rating of your original tires, as well as the inflation pressures needed to obtain the gross weight capacity of your vehicle.
Using heavier suspension components to get added durability might not change your vehicle’s weight ratings. Ask your retailer to help you load your vehicle correctly if you are using these components. Notice: Overloading your vehicle may cause damage.
Towing a Trailer { CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on your vehicle.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You will find these numbers on the Tire-Loading Information label found on the rear edge of the driver’s side rear door or see Loading Your Vehicle on page 4-49 .
And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself. Before you start, check all trailer hitch parts and attachments, safety chains, electrical connector, lamps, tires and mirror adjustment.
When towing a trailer, the arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers behind you are seeing your signal when they are not. It’s important to check occasionally to be sure the trailer bulbs are still working.
3. When the chocks are in place, release the regular brakes until the chocks absorb the load. 4. Reapply the regular brakes. Then apply your parking brake and shift into PARK (P) for an automatic transaxle or REVERSE (R) for a manual transaxle. 5. Release the regular brakes.
Trailer Wiring Additional wire length has been provided for connecting trailer wiring to your vehicle. A loop of five wires is stored below the jack, which is located on the driver’s side of the cargo area. The wires are fused in both the underhood and instrument fuse block.
Service ........................................................... .5-3 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of Your Vehicle ............................................. .5-5 Fuel ................
Wheel Alignment and Tire Balance ................. .5-74 Wheel Replacement ..................................... .5-75 Tire Chains ................................................. .5-76 If a Tire Goes Flat ....................................... .5-77 Changing a Flat Tire .
Service Your Saturn retailer knows your vehicle best and wants you to be happy with it. We hope you will go to your retailer for all your service needs. You will get genuine Saturn parts and Saturn-trained and supported service people. We hope you will want to keep your Saturn vehicle all Saturn.
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-9 .
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your retailer before adding equipment to the outside of your vehicle.
California Fuel If your vehicle is certified to meet California Emission Standards, it is designed to operate on fuels that meet California specifications.
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors recommends that you use these gasolines, particularly if they comply with the specifications described earlier.
Filling Your Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
To remove the fuel cap, turn it slowly to the left (counterclockwise). It will require about 1/2 of a turn to remove the cap. The fuel cap has a spring in it; if you let go of the cap too soon, it will spring back to the right (clockwise). { CAUTION: If you get fuel on yourself and then something ignites it, you could be badly burned.
Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs.
Hood Release To open the hood, do the following: 1. Pull the handle located under the instrument panel on the driver’s side of the vehicle. 2. Then go to the front of the vehicle and lift up on the secondary hood release lever. 3. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot marked PROP ROD.
Engine Compartment Overview When you open the hood on the 2.2L (L61) four cylinder engine, you’ll see the following: 5-12.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-21 . B. Engine Oil Fill Cap. See Engine Oil on page 5-15 . C. Engine Oil Dipstick. See Engine Oil on page 5-15 . D. Brake/Clutch Cylinder Fluid. See Brakes on page 5-41 and Hydraulic Clutch on page 5-28 .
When you open the hood on the 3.5L V6 (L66) engine, you’ll see the following: 5-14.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-21 . B. Engine Oil Dipstick. See Engine Oil on page 5-15 . C. Engine Oil Fill Cap. See Engine Oil on page 5-15 . D. Battery. See Battery on page 5-44 . E. Engine Compartment Fuse Block.
When to Add Engine Oil If the oil is at or below the MIN mark for the 2.2L L4 engine or below the lower mark (B) for the 3.5L V6 engine, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness.
Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty.
As shown in the viscosity chart, SAE 5W-20 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
When to Change Engine Oil (GM Oil Life System) Your vehicle has a computer system that lets you know when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake filter to release loose dust and dirt.
2. Disconnect the hose. 3. Release clamps on side of air cleaner assembly. 4. Rotate cover upward to disengage cover hinges. 5-23.
5. Remove air cleaner cover assembly and air filter element. If the air filter element is dirty, you should replace it. If it is only dusty, it may be cleaned by blowing compressed air through it from the clean side. Make sure you are away from the engine compartment when cleaning the air filter with compressed air.
Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle fluid level is when the engine oil is changed. Change the fluid every 50,000 miles (83 000 km) if the.
Checking the Fluid Level (Automatic Transaxle with 2.2L L4 Engine) Prepare your vehicle as follows: • Park your vehicle on a level place. Keep the engine running.
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use. See Recommended Fluids and Lubricants on page 6-14 . If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick.
Hydraulic Clutch The hydraulic clutch linkage in your vehicle is self-adjusting. The hydraulic clutch system does not have its own reservoir. The system receives fluid from the brake master cylinder reservoir. It is filled with DOT-3 brake fluid. See Brakes on page 5-41 for more information.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL ® coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. { CAUTION: Adding only plain water to your cooling system can be dangerous.
Checking Coolant The surge tank is located on the driver’s side of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location.
Adding Coolant If you need more coolant, add the proper DEX-COOL ® coolant mixture at the surge tank , but only when the engine is cool. See Engine Overheating on page 5-31 for instructions on “How to Add Coolant to the Coolant Surge Tank.” { CAUTION: You can be burned if you spill coolant on hot engine parts.
If Steam Is Coming From Your Engine { CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
If No Steam Is Coming From Your Engine An overheat warning, along with a low coolant light, can indicate a serious problem. See Low Coolant Warning Light on page 3-34 . If you get an engine overheat warning with no low coolant light, but see or hear no steam, the problem may not be too serious.
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Electric Engine Fan B. Coolant Surge Tank with Pressure Cap { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
The coolant level should be at the COLD line (surge tank seam). If it is not, you may have a leak at the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
How to Add Coolant to the Coolant Surge Tank Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. If you have not found a problem yet, check to see if coolant is visible in the surge tank.
{ CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise (left) about one-quarter of a turn. If you hear a hiss, wait for that to stop.
4. With the coolant surge tank pressure cap of f, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coolant level inside the coolant surge tank may be lower.
Windshield Washer Fluid What to Use When you need windshield or rear window (wagon models) washer fluid be sure to read the instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing.
Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down.
What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Recommended Fluids and Lubricants on page 6-14 . Always clean the brake fluid reservoir cap and the area around the cap before removing it.
Brake Wear Your vehicle has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
Brake Pedal Travel See your retailer if the brake pedal does not return to normal height or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you make a moderate brake stop, your brakes adjust for wear.
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( − ) cable from the battery. This will help keep your battery from running down. { CAUTION: Batteries have acid that can burn you and gas that can explode.
Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
{ CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
6. Remove the terminal cover, if equipped, and connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one.
8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery. Use a remote negative ( − ) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative ( − ) cable doesn’t go to the dead battery.
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
All-Wheel Drive If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. However, they have two additional systems that need lubrication. Transfer Case (Power Transfer Unit for 2.2L Engine) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Transfer Case (3.5L Engine) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 6-4 . How to Check Lubricant A: Fill Plug B: Drain Plug To get an accurate reading, the vehicle should be on a level surface.
Bulb Replacement For the type of bulb to use, see Replacement Bulbs on page 5-60 . For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs { CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
4. Rotate the side marker bulb socket counterclockwise and remove it from the housing. 5. Remove the side marker housing. 6. Remove the fasteners from the headlamp assembly.
7. Insert a flat blade screwdriver through the opening in the top. Make sure the screwdriver fits through the opening in the headlamp bracket lower arm. 8. Push the locking tab toward the rear of the vehicle with the screwdriver to lift the headlamp bracket lower arm.
10. Disconnect the electrical connector from the bulb assembly. 11. Rotate the bulb assembly counterclockwise to remove it from the housing. 12. Connect the electrical connector to headlamp bulb assembly. 13. Insert headlamp bulb assembly into headlamp housing, and rotate clockwise until seated.
Fog Lamps 1. Reach through opening in lower front fascia to gain access to the fog lamp bulb electrical connector. 2. Disconnect bulb electrical connector. Lift locking tab and pull the electrical connector rearward to remove the connector. 3. Rotate the bulb socket counterclockwise to remove it.
Center High-Mounted Stoplamp (CHMSL) 1. Remove the center high mount stoplamp (CHMSL) fasteners. 2. Pull the CHMSL out of the liftgate. 3. Disconnect the rear washer hose from the rear washer nozzle. 4. Disconnect the electrical connector from the CHMSL assembly.
Taillamps, Turn Signal, Stoplamps and Back-up Lamps To replace one of these bulbs, do the following: 1. Remove the taillamp fasteners from the body of the vehicle. 2. Slide the taillamp housing rearward and away from the body of the vehicle. 3. Disconnect the taillamp housing electrical connector and remove the taillamp housing.
Replacement Bulbs Exterior Lamp Bulb Number Back-up Lamps 315609442003 CHMSL W5W12092811 Fog Lamps 880C12450143 Front Sidemarker Lamps 16809425542 Front Turn Signal/Parking Lamps 3457A1999370 Headlamp.
4. Pull up the release clip, located at the connecting point of the blade and the arm. Then, pull the blade assembly down toward the glass to remove it from the wiper arm. 5. Push the new wiper blade securely on the wiper arm until you hear the release clip “click” into place.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P-Metric and a LT-Metric tire sidewall.
(A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail.
Tire Size The following examples show the different parts of a tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
(A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letters LT as the first two characters in the tire size means a light truck tire engineered to standards set by the U.
Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Inflation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving.
Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Inflation - Tire Pressure The tire and loading information label, shows the correct inflation pressures for your tires when they are cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).
Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-71 and Wheel Replacement on page 5-75 for more information.
{ CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Buying New Tires To find out what kind and size of tires you need, look at the Certification/Tire label or the Tire and Loading Information label. For examples of these labels and their location on your vehicle, see Loading Your Vehicle on page 4-49 .
{ CAUTION: If you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired).
Used Replacement Wheels { CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new Saturn original equipment wheel.
Notice: If your vehicle has a tire size other than P235/65R16, P235/60R17 or 245/50R18 size tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
1. Lift the forward floor panel of the load floor cargo organizer. 2. Remove the forward floor panel of the load floor cargo organizer and place it in the vehicle while you are removing the spare tire.
3. Open the floor cargo organizer locks, located on the top left and right corners of the organizer, by pushing inward on them. 4. Remove the load floor cargo organizer.
5. Remove the wheel retainer bolt holding down the spare tire. 6. Remove the compact spare tire. See Compact Spare Tire on page 5-88 for more information about the compact spare tire. 7. Remove the wing-bolt on the jack, and remove the jack and wheel wrench.
Removing the Wheel You must take off the wheel cover or hubcap to reach the wheel bolts. For steel wheels with full plastic covers and aluminum wheels with large circular center caps, do the following: 1. Loosen all five hex-shaped plastic caps by turning the wrench counterclockwise.
4. Position the lift head at the jack location nearest the flat tire. Make sure all of the jack lift head is touching the jacking flange under the body. Do not place the jack under a body panel. The lower body panel has an arrow to aid in locating the jacking location.
{ CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
9. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. { CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
13. Tighten the wheel nuts firmly in a crisscross sequence, as shown. { CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts.
Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
6. Place the flat, or damaged tire, face down, on the load floor with the threaded wheel stow rod sticking up through the center hole of the wheel. Vehicles equipped with the 3.5L V6 (L66) engine and aluminum wheels, must remove the center cap from the wheel prior to placing it on the load floor.
Appearance Care Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into flames if a match is struck near them or if they get on a hot part of the vehicle. Some are dangerous if their fumes are inhaled in an enclosed space.
Here are some cleaning tips: • Always read the instructions on the cleaner label. • Clean up stains as soon as you can — before they set. • Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean area often.
Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You may have to do this more than once. • Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner.
Care of Safety Belts Keep belts clean and dry. { CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish.
Cleaning Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Vehicle Care/Appearance Materials See your Saturn retailer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil and asphalt.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Instrument Panel Fuse Block The instrument panel fuse block is located by the passenger’s left leg. Fuses Usage RADIO Radio, Data Link Connector BCM/CLSTR Body Control Module, Instrument Cluster INT.
Underhood Fuse Block The underhood fuse block is located in the forward part of the engine compartment near the battery. Fuses Usage IGNITION Ignition switch BATT FEED I/P Fuse Box COOL 1 Cooling Fan .
Fuses Usage ECM/CAM (3.5L V6 (L66)) Camshaft Sensor, Main Relay Voltage To PCM, Ignition Coils 1-6 ETC (2.2L Four Cylinder (L61)) Engine Control Module (ECM), Electronic Throttle Control FUEL PUMP Fue.
Capacities and Specifications Application Capacities English Metric Air Conditioning Refrigerant R134a 2.2L L4 (L61) 3.5L V6 (L66) 1.5 lbs 1.75 lbs 0.68 kg 0.79 kg Cooling System 2.2L L4 (L61) 3.5L V6 (L66) 7.4 quarts 9.7 quarts 7.0 L 9.2 L Engine Oil with Filter 2.
Engine Specifications Engine VIN Code Transmission Spark Plug Gap 2.2L L4 (L61) F Automatic Manual 0.045 inches (1.14 mm) 3.5L V6 (L66) U Automatic 0.
✍ NOTES 5-104.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using Your Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition.
The services in Scheduled Maintenance on page 6-4 should be performed when indicated. See Additional Required Services on page 6-6 and Maintenance Footnotes on page 6-9 for further information. { CAUTION: Performing maintenance work on a vehicle can be dangerous.
Scheduled Maintenance When the CHANGE OIL SOON light comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km).
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. See Engine Oil on page 5-15 . An Emission Control Service. •• Visually check for any leaks or damage. See footnote (j). •• Inspect engine air cleaner filter.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) V6 engine: Change automatic transaxle fluid (normal service). See footnote (m).
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) V6 engine: Change transfer assembly fluid (normal service). See footnote (m).
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life.
(h) Severe service is when the vehicle is mainly driven under one or more of these conditions: − In heavy city traff ic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. − When doing frequent trailer towing.
Notice: It is important to check your oil regularly and keep it at the proper level. Failure to keep your engine oil at the proper level can cause damage to your engine not covered by your warranty. Engine Coolant Level Check Check the engine coolant level and add DEX-COOL ® coolant mixture if necessary.
On manual transaxle vehicles, put the shift lever in NEUTRAL, push the clutch pedal down halfway and try to start the engine. The starter should work only when the clutch pedal is pushed down all the way to the floor. If the starter works when the clutch is not pushed all the way down, contact your Saturn retailer for service.
Parking Brake and Automatic Transaxle Park (P) Mechanism Check { CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your retailer. Usage Fluid/Lubricant Engine Oil (2.2L engine) Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Rear Drive Module and Power Transfer Unit (except with 3.5L V6 engine) VERSATRAK ® Fluid (GM Part No. U.S. 12378514, in Canada 88901045). Rear Drive Module (with 3.5L V6 engine) VERSATRAK ® Fluid (GM Part No. U.S. 12378514, in Canada 88901045).
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your retailer. Part Saturn Part Number ACDelco ® Part Number Engine Air Cleaner/Filter 22676970 — Engine Oil Filter 2.
Engine Drive Belt Routing 2.2L Four Cylinder (L61) Engine 3.5L V6 (L66) Engine 6-17.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 . Any additional information from Owner Checks and Services on page 6-10 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-19.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-20.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-4 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn. Together we are committed to providing our customers with unparalleled service, before, during and after the purchase of a Saturn vehicle, for total customer satisfaction.
In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd. 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 When contacting Saturn, please remember that your concern will likely be resolved at a retailer’s facility. That is why we suggest you follow Step One first if you have a concern.
Online Owner Center The Owner Center is a resource for your GM ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders.
GM Mobility Program for Persons with Disabilities This program, available to qualified applicants, can reimburse you up to $1,000 toward eligible aftermarket driver or passenger adaptive equipment you may require for your vehicle (hand controls, wheelchair/ scooter lifts, etc.
Roadside Assistance Program For vehicles purchased in the U.S. call 1-800-553-6000 (TTY: 1-800-833-6000). For vehicles purchased in Canada call 1-800-268-6800. As the proud owner of a new Saturn vehicle, you are automatically enrolled in the Saturn Roadside Assistance Program.
• Model, year, color, and license plate number • Mileage, Vehicle Identification Number and delivery date of the vehicle • Description of the problem While we hope you never have the occasion to use our service, it is added security while traveling for you and your family.
To read this information, special equipment is needed and access to the vehicle or the SDM is required. GM will not access information about a crash event or share it with others other than • with t.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited.
Owner Publications Information on how to obtain product bulletins and as described below is applicable only in the fifty U.S. states and the District of Columbia, and only for cars and light trucks with a GVWR less than 10,000 pounds (4 536 kg). Copies of individual bulletins are also at your participating Saturn retailer.
A About Driving Y our V ehicle .................................... i i Accessory Power Outlets ................................. 3-20 Activating the Theft-Deterrent Feature ................ 3-72 Adding a Snow Plow or Similar Equipment ......... 4-54 Adding Windshield W asher Fluid .
Audio System(s) (cont.) Setting the T ime for Radios with Radio Data Systems (RDS) ................................ 3-43 Setting the T ime for Radios without Radio Data Systems (RDS) ....................... 3-43 Theft-Deterrent Feature ...............
Care of Safety Belts ................................................ 5-92 Y our CD and DVD Player ............................. 3-75 Y our CDs and DVDs .................................... 3-75 Cargo Lamp .............................................
Control of a V ehicle .......................................... 4 - 7 Coolant Engine T emperature Gage ............................ 3-34 Engine T emperature Warning Light ................. 3-33 Heater , Engine ........................................
Driving (cont.) Freeway ..................................................... 4-36 Hill and Mountain Roads .............................. 4-38 In Rain and on Wet Roads ........................... 4-32 Winter ...........................................
Engine Air Cleaner/Filter Replacement ............... 5-21 Engine Cooling When Trailer T owing .................. 4-61 Engine Oil Additives ........................................ 5-19 Entry Lighting ................................................. 3-19 Environmental Concerns .
G Gage Engine Coolant T emperature ......................... 3-34 Fuel .......................................................... 3-41 Speedometer .............................................. 3-27 T achometer ........................................
If Y ou Are Caught in a Blizzard ......................... 4-42 If Y ou Do Decide to Pull a T railer ...................... 4-56 Ignition Positions ............................................. 2-14 Infants and Y oung Children, Restraints ............
Light (cont.) TCS W arning Light ...................................... 3-32 T raction Control System (TCS) W arning .......... 3-32 Up-Shift ..................................................... 3-30 Load Floor Storage Box ...........................
Mirrors (cont.) Automatic Dimming Rearview with OnStar ® , Compass and T emperature Display ............. 2-29 Manual Rearview Mirror ................................ 2-29 Outside Convex Mirror ................................. 2-34 Outside Manual Mirrors .
Playing the Single CD Player ........................... 3-54 Playing the Six-Disc CD Player ......................... 3-56 Power ............................................................. 1 - 3 Accessory Outlets ...................................
Replacement Bulbs ......................................... 5-60 Replacing Brake System Parts .......................... 5-44 Reporting Safety Defects Canadian Government ................................... 7 - 9 Saturn ...............................
Securing a Child Restraint Designed for the LA TCH System ................... 1-42 Rear Seat Position ...................................... 1-42 Right Front Seat Position .............................. 1-45 Security Light ............................
TCS W arning Light .......................................... 3-32 T emperature and Compass Display .................... 2-29 T emperature Display ........................................ 2-31 Theft-Deterrent, Radio ...................................
U Underhood Fuse Block ................................... 5-100 Understanding Radio Reception ........................ 3-74 Uniform T ire Quality Grading ............................ 5-73 Unlocking the Theft-Deterrent Feature After a Power Loss .....
When to Check and Change ............................ 5-25 When to Inspect the Engine Air Cleaner/Filter ..... 5-21 When Y ou Are Ready to Leave After Parking on a Hill ......................................... 4-61 Where to Put the Restraint ........
デバイスSaturn 2004 Vueの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Saturn 2004 Vueをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSaturn 2004 Vueの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Saturn 2004 Vueの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Saturn 2004 Vueで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Saturn 2004 Vueを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSaturn 2004 Vueの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Saturn 2004 Vueに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSaturn 2004 Vueデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
