Scag Power EquipmentメーカーGC-STC-CSの使用説明書/サービス説明書
ページ先へ移動 of 18
MODEL GC-STC-CS THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJURY . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1. With the hopper door closed, engage the deck drive. 2. Proceed to mow until the hopper is full. A replacement manual is available from your authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050.
2 3. When dumping the hopper into a disposal area: A . Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. B . Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper .
3 3.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
4 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . FIGURE 3-2 FIGURE 3-3 ELASTIC ST OP NUT FLA T W ASHER CARRIAGE BOL T RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
5 10 . Install the new belt covers and secure. See items number 1 and number 21 on page 10 of the Blower Mounting Components section in the Illustrated Parts List for proper installation. 11 . Install the hopper mounting brackets to the outside of the frame on the rear of the machine.
6 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 4-1. 3. Remove the pin and hair pin holding the blower assembly to the mounting bracket on the cutter deck and remove the blower assembly.
7 Notes.
8 GC-STC 48" & 52" BLO WER HOUSING ASSEMBL Y W A R N IN G IN S T A L L B E L T C O V E R B E F O R E O P E R A T IN G M A C H IN E R E A D O P E R A T O R ' S M A N U A L 2005 GC Bl.
9 GC-STC 48" & 52" BLO WER HOUSING ASSEMBL Y Ref. Pa r t No . Number Description 27 04019-04 Nut, Serr . Flange 3/8-16 28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr . 8 29 481377 Decal, Danger 30 461681 Blower Housing Assembly 31 04003-12 Bolt, Carr .
10 GC-STC 48" & 52" BLO WER MOUNTING COMPONENTS 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 16 17 18 19 20 390STC203B 21 22 6 RIGHT SIDE OF CUTTER DECK SHOWN UNDER SIDE OF CUTTER DECK SH.
11 GC-STC 48" & 52" BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482612 B el t Co v er , GC-STC 2 04029-04 Wi ngnut, Plastic 3/8" Small 3 482300 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter , Blower GC-STC , includes item #7 6 04040-14 Flatwasher , 1/4-.
12 A A B B C C 2005 CSHOPPEREXPLOD-ST C 1 16 45 15 14 45 43 56 55 6 17 41 50 5 4 3 49 31 51 11 40 58 59 25 12 8 9 34 49 50 24 34 29 42 27 48 38 53 10 33 61 60 37 19 36 20 49 33 21 57 38 32 35 46 37 49.
13 GC-STC-CS HOPPER COMPONENTS Ref. Pa r t No . Number Description 1 461627 Hopper , GC-STC-CS 2 482732 Door , GC-CS 3 461626 Sweeper Weldment, GC-CS 4 482777 Pad, Rubber 5 04090-02 P op Ri v et, 3/16 x .652 6 423834 Plate, Stiffener 7 423938 Suppor t F rame, Hopper 8 423849 Hinge Bracket, L.
14 GC-STC-CS DECALS 481039 482275 481327 483037 481377 483039.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03156 PRINTED 8-2004 PRINTED IN USA © 2004 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC www .scag.com.
デバイスScag Power Equipment GC-STC-CSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Scag Power Equipment GC-STC-CSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはScag Power Equipment GC-STC-CSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Scag Power Equipment GC-STC-CSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Scag Power Equipment GC-STC-CSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Scag Power Equipment GC-STC-CSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はScag Power Equipment GC-STC-CSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Scag Power Equipment GC-STC-CSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちScag Power Equipment GC-STC-CSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
