Scag Power EquipmentメーカーGC-STT-CSの使用説明書/サービス説明書
ページ先へ移動 of 28
MODEL GC-STT-CS THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJURY . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 3. When dumping the hopper into a disposal area: A . Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. B . Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper .
3 3.1 ASSEMBLY INSTRUCTIONS FOR 52" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
4 RIGHT SIDE OF 52" CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS HEX HEAD BOL T ELASTIC STOP NUTS.
5 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the hardware at this time.
6 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 18 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
7 4.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
8 RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L .
9 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 4-3, Page 8. Do not fully tighten the hardware at this time.
10 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 16 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
11 5.1 ASSEMBLY INSTRUCTIONS FOR 72" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
12 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
13 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 5-3, Page 12. Do not fully tighten the hardware at this time.
14 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 17 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
15 FIGURE 5-6 Liquid Cooled Only Note: Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model.
16 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley. 4. Remove the pin holding the blower assembly to the mounting bracket on the cutter deck and remove the blower assembly.
17 Notes.
18 GC-STT BLO WER HOUSING ASSEMBL Y W A R N IN G INSTALL BEL T COVER BEFORE OPERATING M ACHINE R E A D O P E R A T O R ' S M A N U A L 390STT0200A 1 2 3 3 45 47 45 4 5 6 7 8 9 9 10 10 11 11 12 12.
19 GC-STT BLO WER HOUSING ASSEMBL Y Ref. Pa r t No . Number Description 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr .
20 GC-STT BLO WER MOUNTING COMPONENTS 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 19 20 21 16 17 18 390STT0203 RIGHT SIDE OF 61" CUTTER DECK SHOWN Note: Parts for 52"cutter deck may vary slightly from illustration. Some parts not shown for viewing purposes.
21 GC-STT BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482406 Belt Cov er , GC-STT - 52" 482378 B e lt C ov e r , GC-STT - 61" & 72" 2 04029-04 Wingnut, Plastic 3/8 Small 3 482300 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461419 Adapter , Blow er GC-STT 6 04040-14 Flatwasher , 1/4-.
22 GC-STT -CS HOPPER COMPONENTS A A B B C C CSHOPPEREXPLODE2-STT 1 16 45 15 14 45 43 56 55 6 17 41 50 5 4 3 49 31 51 11 40 58 59 25 12 8 9 34 49 50 24 34 29 42 27 48 38 53 10 33 61 60 37 19 36 20 4 9 .
23 GC-STT -CS HOPPER COMPONENTS Ref. Pa r t No . Number Description 1 461627 Hopper , GC-STT -CS 2 482732 Door , GC-CS 3 461626 Sweeper Weldment, GC-CS 4 482777 Pad, Rubber 5 04090-02 P op Ri v et, 3/16 x .652 6 423834 Plate, Stiffener 7 423831 Suppor t F rame, Hopper 8 423849 Hinge Bracket, L.
24 GC-STT DECALS 481039 482275 482733 482293.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03140 PRINTED 8-2003 PRINTED IN USA © 2003 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC www .scag.com.
デバイスScag Power Equipment GC-STT-CSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Scag Power Equipment GC-STT-CSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはScag Power Equipment GC-STT-CSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Scag Power Equipment GC-STT-CSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Scag Power Equipment GC-STT-CSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Scag Power Equipment GC-STT-CSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はScag Power Equipment GC-STT-CSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Scag Power Equipment GC-STT-CSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちScag Power Equipment GC-STT-CSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
